Matrix TL10 Handleiding
Pagina's 2 Niet gecategoriseerd
Bekijk de handleiding van Matrix TL10 gratis online of download de PDF. Deze handleiding is 1 keer bekeken. Vraag over dit model? Stel een vraag
T- Single Lever MonoblocL10CH
5 Year warranty:
In the unlikely event that you should experience any defect in the materials or workmanship of your new mixer within FIVE years of
purchase, the purchaser’s sole remedy shall be the replacement (at the manufacturer’s discretion) of all or any part of the product that is
defective. All working parts and valves are guaranteed for a period of FIVE years from purchase. Decorative surface finishes and O-rings
are guaranteed for ONE year from the date of purchase provided that our advice concerning care has been observed. This is provided
that the mixer has been used for normal domestic purposes in the UK & Ireland and that the care, installation and maintenance
instructions have been observed. The warranty extends to the original purchaser only. The Manufacturer shall not be liable for either
servicing of the product or incidental loss due to the product. You should retain a copy of your dated invoice as proof of purchase to
validate any claims under this guarantee.
Care Instructions for your Kitchen Sink Mixer:
To maintain the appearance of this tap, ensure that it is regularly cleaned only using a clean, soft damp cloth. A solution of warm water
and a mild liquid detergent may be used where necessary, and then the fitting rinsed thoroughly and wiped dry. Any other cleaning
action will invalidate your warranty. If the tap has a diffuser it should be unscrewed and cleaned of dirt and scale periodically to maintain
performance.
Abrasive cleaners, scouring cleaners and acidic cleaners under any circumstances. Avoid contact with all solvents must not be used
(including chlorinated solvents, ketones or acetones as these may result in surface deterioration or etching). Also avoid contact with any
harsh household chemicals such as oven cleaners, drain cleaners, rust removers, paint strippers and toilet bowl cleaners, bar keepers
friend or Brasso.
Important Technical Data:
Minimum operating pressure 0.4 bar Maximum hot water temperature 60°C*
Maximum operating pressure 5.5 bar* Recommended hot water temperature 46°C
*If these temperatures or pressures are exceeded, even for short periods, damage can result.
This tap is either WRAS approved or manufactured in accordance with recognised European standards. Please ensure that your Kitchen
mixer is fitted in accordance with Local Water Byelaws.
These installation guidelines have been prepared for your direction and you must exercise due care at all times. We do not accept
responsibility for problems that may occur through improper installation. Whilst assembling the tap take care not to accidentally loosen
any screwed assemblies.
Where the tap has a removable aerator on the spout exit it can be removed and cleaned periodically to maintain optimum flow
performance.
Installation Preparation:
All parts should be removed from their packaging and inspected for completeness and transport damage prior to installation.
Before installing the new mixer it is essential that you thoroughly flush through the supply pipes in order to remove any remaining
solder, swarf or impurities from your system. Failure to carry out this simple procedure could cause problems or damage to the workings
of the mixertap.
We strongly recommend installing isolation valves to both the hot and cold feed pipes in an accessible position. This will help to ease any
future maintenance if required.
Shut off your water heating system and ensure that your mains stopcock is closed. Open the lowest hot and cold taps in the house and
allow the water to run until the cold-water storage tank and pipes are fully empty. Please note, the hot water storage cylinder (if
applicable) will remain full.
This mixertap requires a 35mm tap hole, if replacing an existing tap, remove the tap & clean the end of the feed pipes using wire wool
the tap hole area should be free from dirt and sealant.
Loosely position the tap and tail pipes to check if any alteration to the existing pipework is required, if this is the case do this now.
Installation:
1.Note that the handle moves 45° left (hot) and 45° right
(cold) of the centre (mixed water) position. Decide on the
required alignment of the tap handle to the sink bowls and
the relevant resting position of the spout (see fig 1 for a
suggested alignment). Note also that the spout is designed
to rotate 360°
Fig 1
2.S
crew the studded rod (C) into the base of the tap (A).
3.Screw the tail pipes (G) into the base of the tap (A), note the
hot water should be connected to the left of the tap when
viewed from the front.
4.Pass the upper seal (B) over the studded rod (C) and tail
pipes (G) and locate it centrally on the base of the mixertap
(A).
5.Place the mixertap (A) onto the sink or worktop and pass the
tail pipes (G) and studded rod (C) through the taphole. With
the tap in place check that the tail pipes (G) meet the hot
and cold water feeds. If further adjustment to the plumbing
is required do this now.
6.Pass the rubber horseshoe (D) and then metal horseshoe (E)
over the studded rod (C) and around tail pipes (G).
7.Fasten fixing nut (F) securely onto the studded rod (C) fixing
the tap into its correct location.
8.Connect the tail pipes (G) to the 15mm water supplies using
the compression fittings (H & I).
K
ey: Description: Qty
A Tap body 1
B Upper seal 1
C Studded rod 1
D Rubber horseshoe 1
E Metal horseshoe 1
F Fixing nut 1
G 1/2” tail pipes 2
H Compression olives 2
I Compression nuts 2
After installation:
Once you have visually checked the new fittings and connections, ensure that all taps are closed except the new mixer tap, which should
be left open. Turn on the water supply at the mains stop cock. As the system starts to refill, . Once you are fully check carefully for leaks
satisfied that there are no leaks, turn on the water heating.
Clean the tap to remove any marks created during installation as instructed then replace the bag that has been provided to protect the
tap
until it is ready for use.
FOR SPARES & TECHNICAL SUPPORT CALL: 01949 862012
Product specificaties
| Merk: | Matrix |
| Categorie: | Niet gecategoriseerd |
| Model: | TL10 |
Heb je hulp nodig?
Als je hulp nodig hebt met Matrix TL10 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden