Marshall CV-RCP-V2 Handleiding
Marshall
Niet gecategoriseerd
CV-RCP-V2
Bekijk gratis de handleiding van Marshall CV-RCP-V2 (1 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 16 mensen en kreeg gemiddeld 4.8 sterren uit 8.5 reviews. Heb je een vraag over Marshall CV-RCP-V2 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/1
CV
CV
CV
CVCV-RC
-RC
-RC
-RC-RCP-
P-
P-
P-P-V2
V2
V2
V2 V2
T
T
T
TTou
ou
ou
ououchs
chs
chs
chschscre
cre
cre
crecree
e
e
een R
n R
n R
n Rn RCP
CP
CP
CPCP Ca
Ca
Ca
Ca Came
me
me
memera
ra
ra
rara Co
Co
Co
Co Cont
nt
nt
ntntro
ro
ro
rorol
l
l
l l
Q
Q
Q
QQuick
uick
uick
uickuick St
St
St
St Start
art
art
art art G
G
G
GGuide
uide
uide
uideuide
Inial Startup & Connection Instrucons for Marshall CV-RCP-V2
Package contents
1 x CV-RCP-V2 Camera Control RCP Touchscreen unit
1 x Universal 12V Power Supply (2.1mm connector) unit
Required for hookup
3-pin XLR cable to desired lengths (male into RCP) and 3-pin XLR splits for
mulple camera setups
Connecon instrucons
1) Connect the 12V Power Supply to the DC power connector on
RCP and plug into a wall outlet to power up and inialize soware (rst
boot up might take up to 25 seconds).
2) Source and connect the male end of a 3-pin XLR cable to the
TOP of the RCP unit (see pic to le) and push into place.
3) Splice raw XLR wires on camera-
side and insert into RS485 phoenix
connector (on breakout cable) when using
camera models CV505/565/345/365 (see pic
to the right) directly into RS485 port on or
rear panel of CV502/343/350 camera models.
4) Hold down rst camera assignment (circle) on upper screen of
RCP unit (4-5 seconds), then Select Camera Model, Select Output
Format, assign RCP Label ID, and Camera ID# to 1 (one) and
match in OSD Menu of Camera under DISPLAY CONTROL > CAM
ID > 1. Assign Camera Model on RCP to correspond to Camera
being used and push “Apply” (see pic to right)…use 2, 3, 4, 5, 6,
and 7 on mulple cameras being setup.
5) Repeat up to 7 (seven) cameras on RCP and OSD Menu of
Camera to match control posion on RCP, use Y-cable spliers at
each camera.
6) Once setup, try to open OSD (under OSD tab) or make
adjustments to WB, Exp, or other to see if control is operaonal.
7) : If control doesn’t work inially, swap the wires on the NOTE
phoenix connector of camera (will not damage either
component) and try again.
8) For mul-camera setup use 3-pin XLR (Y-SPLITS) at each camera
or a mul-splier.
Help Tab
CV-RCP-V2 is setup with a tab feature to explain certain buons in Help
RCP. The “Help” tab will ash while in the help mode and dierent
buons can be pressed for further explanaon.
TECH NOTE: before removing power please go to Adv
tab first and select SHUTDOWN to exit Software.
Please NOTE: before removing power from RCP,
please go to Adv TAB and select SHUTDOWN first
before removing power to exit Software.
Product specificaties
| Merk: | Marshall |
| Categorie: | Niet gecategoriseerd |
| Model: | CV-RCP-V2 |
Heb je hulp nodig?
Als je hulp nodig hebt met Marshall CV-RCP-V2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Marshall
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
11 Juni 2025
10 Juni 2025
10 Juni 2025
Handleiding Niet gecategoriseerd
- WiZ
- Flex
- Point
- Challenge
- BeeSecure
- Pentair
- Vitamix
- J. Rockett Audio Designs
- Venta
- Neets
- Shure
- Walkstool
- Berker
- Invacare
- Revlon
Nieuwste handleidingen voor Niet gecategoriseerd
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
31 Juli 2025
30 Juli 2025
30 Juli 2025