Marmitek MS13 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Marmitek MS13 (40 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/40
MS13E
WIRELESS
MOTION SENSOR
MS13E
WIRELESS
MOTION SENSOR
USER MANUAL 3
GEBRAUCHSANLEITUNG 9
GUIDE UTILISATEUR 15
MODO DE EMPLEO 21
MANUALE D’ISTRUZIONI 27
GEBRUIKSAANWIJZING 33
20155/20061107 • MS13E™
WIRELESS MOTION SENSOR
ALL RIGHTS RESERVED MARMITEK©2007
TM
2 © MARMITEK
MS13E – WIRELESS MOTION SENSOR
SAFETY WARNINGS
• Do not expose the components of your systems to extremely high temperatures or bright light sources.
• The product should only be repaired or serviced by a qualified repairman.
• In case of improper usage or if you have opened, altered and repaired the product yourself, all
guarantees expire. Marmitek does not accept responsibility in the case of improper usage of the
product or when the product is used for purposes other than specified. Marmitek does not accept
responsibility for additional damage other than covered by the legal product responsibility.
• Batteries: keep batteries out of the reach of children. Dispose of batteries as chemical waste. Never use
old and new batteries or different types of batteries together. Remove the batteries when you are not
using the system for a longer period of time. Check the polarity (+/-) of the batteries when inserting
them in the product. Wrong positioning can cause an explosion.
• This product is not a toy. Keep out of reach of children.
• Automatic switching devices provide comfort, but can also be dangerous. They can surprise people or
can ignite clothing hanging over an electric heat source. Please be careful and take appropriate
measures to avoid accidents.
HOW DOES MARMITEK X-10 WORK?
Marmitek X-10 components use the existing mains wiring to communicate (using Marmitek X-10 signals).
You can build a complete system using the three different kind of components of the Marmitek X-10
System:
1. Modules: These components will receive Marmitek X-10 signals and will switch or dim the
attached lamp or appliance.
2. Controllers: These components will transmit Marmitek X-10 signals and thus will control the Modules.
3. Transmitters: Wireless components like remotes. The signals of these components will be received by
a controller with transceiver functionality (IRRF 7243, TM13 or console of a Marmitek
Security System). The Transceiver will translate the signals into Marmitek X-10 signals on
the power line.
ADRESSES
Up to a maximum of 256 different addresses can be preset. These are subdivided into a so-called
HouseCode (A to P incl.) and a UnitCode (1 to 16 incl.). The HouseCode can also be set on the controllers,
so that the controllers and modules become part of the same system. The address can be set either using
code dials or by pressing buttons, depending on the type of module.
The Marmitek X-10 System uses standard commands, which control all units with the same HouseCode at
the same time (e.g. all lights on, all off, etc.).
SIGNAL RANGE
Range of Marmitek X-10 signals over the Power Line and how to increase the range.
The Marmitek X-10 System is based on power line communication. The range of the Marmitek X-10 signals
very much depends on the local circumstances. On average the range is a cable length of 80 meters.
If you have difficulties with the range of your Marmitek X-10 signals, please pay attention to the
following facts:
3MS13T M
ENGLISH


Product specificaties

Merk: Marmitek
Categorie: Niet gecategoriseerd
Model: MS13

Heb je hulp nodig?

Als je hulp nodig hebt met Marmitek MS13 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Marmitek

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd