Manhattan 180535 Handleiding

Manhattan Niet gecategoriseerd 180535

Bekijk gratis de handleiding van Manhattan 180535 (16 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 21 mensen en kreeg gemiddeld 4.5 sterren uit 11 reviews. Heb je een vraag over Manhattan 180535 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/16

For additional benefits

10-Port AC

Charging Cabinet

Instructions

Model 180535

or visit: register.manhattanproducts.com/r/180535

Scan to

product warranty

For specifications, please visit manhattanproducts.com register.. Register your product at

manhattanproducts.com/r/180535 or scan the QR code on the cover.

Setup

1 Unlock unit door and open it.

2 To fit larger devices, remove bay divider(s).

• Unscrew bar and set it aside.

• To remove divider, pull up on the clip to release it from the bar it’s attached to.

• When enough dividers are removed, replace numbered bar and screws.

3 Connect devices to power outlets with appropriate cables. Secure cables with wire clips on dividers.

• Remove screws that hold the power box in place; slide the power box out.

• Connect power cables to power outlets, feeding cables through holes on power panel.

• Push the power box back in and replace the screws that hold it in place.

• Load devices in bays.

• Connect cables to devices.

Charging

4 Connect unit power cable to power outlet. Unit automatically begins to charge devices.

Installation Options

The following sections offer optional steps to complete installation.

To Reverse the Door — NOTE: Make sure all power is cut off from unit!

1 Unscrew grounding cable from door and cabinet. Remove door from cabinet by pulling L-shaped pins.2

Instructions

English

3 Flip door and guide pins into holes on other side of

cabinet frame. Release pins and ensure door is

secure.

4 Reattach grounding cable to door and cabinet.

Mounting to the Wall

1 At desired location on wall, use the spacing

shown in the graphic below to mark four level

drill positions for the cabinet holes.

Concrete wall: use a 15/64” (6 mm) bit to drill

holes 2.4 in. (60 mm) deep at marks.

Wood-stud walls: use a 15/64” (6 mm) bit to

make pilot holes 2.4 in. (60 mm) deep at marks.

2 Install included screws into holes so they

protrude 0.4 in. (10 mm) from the wall.

3 Position cabinet holes over wall screws and

hang cabinet on them. Installation is complete.

Stacking the Units — NOTE: Make sure all power is cut off from unit!

Stacking material not included; refer to website.

1 Unscrew the screws on the power box.

2 Slide the power box out.

3 Align the stacking holes on the top and bottom of

the cabinets.

4 Tighten screws (not included) into both cabinets

from the ceiling of the bottom cabinet.

5 Reinstall the power box with its screws.

16in. (406.4 mm)

16.57in. (420.86mm)

2 in.

(50mm)

NOTE: a 13 mm

(0.51 in.) gap exists.

Instructions

English

Product specificaties

Merk:	Manhattan
Categorie:	Niet gecategoriseerd
Model:	180535
Kleur van het product:	Zwart
Gewicht:	15000 g
Breedte:	437 mm
Diepte:	460 mm
Hoogte:	485 mm
Snoerlengte:	2 m
Gewicht verpakking:	16000 g
Breedte verpakking:	460 mm
Diepte verpakking:	437 mm
Hoogte verpakking:	485 mm
Soort:	Kast voor draagbaar apparaatbeheer
Gebruikershandleiding:	Ja
Materiaal behuizing:	Polycarbonate (PC), Steel
Stroom:	16 A
Plaatsing:	Muur
Meegeleverde kabels:	AC
Met slot:	Ja
Certificering:	CE\nRoHS
Temperatuur bij opslag:	-15 - 45 °C
Stroomspanning bescherming:	Over current, Over voltage, Short circuit
Stapelbaar:	Ja
Montagebeugels meegeleverd:	Ja
AC-ingangsspanning:	100 - 250 V
AC-ingangsfrequentie:	50 - 60 Hz
Bedrijfstemperatuur (T-T):	0 - 45 °C
Relatieve vochtigheid in bedrijf (V-V):	20 - 80 procent
Maximale schermgrootte:	15.6 "
Number of devices supported:	10
Ondersteunde draagbare apparaten:	Notebook
Slot type:	2 toetsen
Aantal sleutels meegeleverd:	2 stuk(s)
Sleufbreedte:	30 mm
Sleufdiepte:	380 mm
Sleufhoogte:	280 mm