Makita DP4011 Handleiding

Makita Schroef-boormachines DP4011

Lees hieronder de 📖 handleiding in het Nederlandse voor Makita DP4011 (8 pagina's) in de categorie Schroef-boormachines. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8

ENGLISH (Original instructions)

INSTRUCTION MANUAL

DOUBLE INSULATION

IMPORTANT: Read Before Using.

2-speed drill

DP4010

DP4011

008321

ENGLISH (Original instructions)

SPECIFICATIONS

Model DP4010/DP4011

Speed High Low

Steel 8 mm 13 mm

Capacities Wood 25 mm 40 mm

No load speed (min

-1) 0 - 2,900 0 - 1,200

Overall length 347 mm

Net weight 2.3 kg

Safety class /II

• Due to our continuing program of research and development, the specifications herein are subject to change without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

END201-5

Symbols

The following show the symbols used for the equipment.

Be sure that you understand their meaning before use.

･ Read instruction manual.

･ DOUBLE INSULATION

･ Only for EU countries

Do not dispose of electric equipment

together with household waste material!

In observance of European Directive

2002/96/EC on waste electric and electronic

equipment and its implementation in

accordance with national law, electric

equipment that have reached the end of their

life must be collected separately and

returned to an environmentally compatible

recycling facility.

ENE032-1

Intended use

The tool is intended for drilling in wood, metal and plastic.

ENF002-1

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated in accordance with European Standard

and can, therefore, also be used from sockets without

earth wire.

ENG104-1

For European countries only

Noise

The typical A-weighted noise level determined according

to EN60745:

Sound pressure level (L

pA) : 80 dB (A)

Uncertainty (K) : 3 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection

ENG202-3

Vibration

The vibration total value (tri-axial vector sum) determined

according to EN60745:

Work mode: drilling into metal

Vibration emission (ah,D) : 2.5 m/s2 or less

Uncertainty (K) : 1.5 m/s2

ENG901-1

• The declared vibration emission value has been

measured in accordance with the standard test

method and may be used for comparing one tool

with another.

• The declared vibration emission value may also be

used in a preliminary assessment of exposure.

WARNING:

• The vibration emission during actual use of the

power tool can differ from the declared emission

value depending on the ways in which the tool is

used.

• Be sure to identify safety measures to protect the

operator that are based on an estimation of

exposure in the actual conditions of use (taking

account of all parts of the operating cycle such as

the times when the tool is switched off and when it

is running idle in addition to the trigger time).

ENH101-17

For European countries only

EC Declaration of Conformity

Makita declares that the following Machine(s):

Designation of Machine:

2-speed drill

Model No./ Type: DP4010,DP4011

Conforms to the following European Directives:

2006/42/EC

They are manufactured in accordance with the following

standard or standardized documents:

EN60745

The technical file in accordance with 2006/42/EC is

available from:

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

31.12.2013

000331

Yasushi Fukaya

Director

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

GEA005-3

General Power Tool Safety

Warnings

WARNING Read all safety warnings and all

instructions.

Failure to follow the warnings and instructions

may result in electric shock, fire and/or serious injury.

Save all warnings and

instructions for future reference.

The term "power tool" in the warnings refers to your

mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while

operating a power tool. Distractions can cause

you to lose control.

Electrical safety

4. Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and

refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet

conditions. Water entering a power tool will

increase the risk of electric shock.

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electric shock.

9. If operating a power tool in a damp location is

unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces

the risk of electric shock.

10. Use of power supply via a RCD with a rated

residual current of 30mA or less is always

recommended.

Personal safety

11. Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the influence of drugs, alcohol or

medication. A moment of inattention while

operating power tools may result in serious

personal injury.

12. Use personal protective equipment. Always

wear eye protection. Protective equipment such

as dust mask, non-skid safety shoes, hard hat, or

hearing protection used for appropriate conditions

will reduce personal injuries.

13. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting

to power source and/or battery pack, picking

up or carrying the tool. Carrying power tools with

your finger on the switch or energising power tools

that have the switch on invites accidents.

14. Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may

result in personal injury.

15. Do not overreach. Keep proper footing and

balance at all times. This enables better control

of the power tool in unexpected situations.

16.

Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves

away from moving parts.

Loose clothes, jewellery or

long hair can be caught in moving parts.

17. If devices are provided for the connection of

dust extraction and collection facilities,

ensure these are connected and properly used.

Use of dust collection can reduce dust-related

hazards.

Power tool use and care

18. Do not force the power tool. Use the correct

power tool for your application. The correct

power tool will do the job better and safer at the

rate for which it was designed.

19. Do not use the power tool if the switch does

not turn it on and off. Any power tool that cannot

be controlled with the switch is dangerous and

must be repaired.

Product specificaties

Merk:	Makita
Categorie:	Schroef-boormachines
Model:	DP4011
Gewicht:	2300 g
Soort:	Boor
Stroombron:	AC
Input vermogen:	720 W
Inactieve snelheid (1ste versnelling):	1200 RPM
Inactieve snelheid (2e versnelling):	2900 RPM
Stationair toerental (max):	2900 RPM
Boor diameter in staal (max):	13 mm
Aantal versnellingen:	2
Reverse:	Ja
Boorhouder:	Zonder sleutel