M-Audio BX8 D3 Handleiding

M-Audio Monitor BX8 D3

Bekijk gratis de handleiding van M-Audio BX8 D3 (28 pagina’s), behorend tot de categorie Monitor. Deze gids werd als nuttig beoordeeld door 65 mensen en kreeg gemiddeld 4.0 sterren uit 33 reviews. Heb je een vraag over M-Audio BX8 D3 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Download PDF

Pagina 1/28

User Guide

User Guide User Guide

English ( 2 – 6 )

Guía del usuario

Guía del usuario Guía del usuario

Español ( 7 – 11 )

Guide d’utilisation

Guide d’utilisationGuide d’utilisation

Français ( 12 – 16 )

Guida per l’uso

Guida per l’uso Guida per l’uso

Italiano ( 17 – 21 )

Benutzerhandbuch

Benutzerhandbuch Benutzerhandbuch

Deutsch ( 22 – 26 )

Appendix

Appendix Appendix

English ( 27 )

MIC/LI NEMIC/LI NE

M-TRACK

2X2M

C -SERIES

User Guide ( )English

Introduction

Box Contents

BX8 D3

Power Cable

Acoustic Foam Pad

User Guide

Safety & Warranty Manual

Support

For the latest information about this product (documentation, technical specifications, system

requirements, compatibility information, etc.) and product registration, visit m-audio.com.

For additional product support, visit m-audio.com/support.

Setup

Connection Diagram

Items not listed under Introduction > Box Contents are sold separately.

Audio

Interface

Power

Features

Rear Panel

1. XLR Input: This jack accepts XLR input

connections with either balanced or

unbalanced wiring. The input wiring of an

XLR connector should be as follows:

• XLR Pin 1: signal ground (shield)

• XLR Pin 2: signal positive (+)

• XLR Pin 3: signal negative (–)

2. TRS Input: This jack accepts 1/4" (6.35 mm)

connections with either balanced or

unbalanced wiring. For balanced wiring, a

three-conductor TRS plug is necessary. The

input wiring of a TRS connector should be as

follows:

• TRS Tip: signal positive (+)

• TRS Ring: signal negative (–)

• TRS Sleeve: signal ground (shield)

3. Acoustic Space Switch: Your BX8 D3

monitors should ideally be placed at least

one foot away from the nearest wall, ceiling,

or other large, flat surface. However, this may

be impractical due to space limitations within

your studio. For that reason, BX8 D3

monitors feature an acoustic space switch.

This switch compensates for placement near

walls.

Tip: Be sure to leave at least 3" of space between the rear of the speaker and a wall to allow the

rear-firing port to "breathe" properly. Placing the speaker any closer than 3" may adversely

affect low-frequency response.

4. Sub-Frequency Vent Port: This port aids in reproduction of very low frequencies by

discharging frequencies below 60 Hz and to act as a cooling mechanism to prevent

overheating. This port should not be blocked.

5. Volume Control: Use the volume control to set the output from the BX8 D3 to proper levels as

required.

6. Power Switch: This switch turns the monitor on and off.

Note: This product does not have a standby/low-power mode.

7. Power Receptacle: Accepts a detachable 3-conductor IEC power cord in order to power the

monitor.

8. Fuse Holder: Holds the external main fuse.

9. Voltage-Select Switch: Provides two selections, 115V AC and 230V AC, and should be set to

match the "house supply" (receptacle) mains voltage of the country or location in which the

speaker is used. The 115V setting is correct for the USA, while the 230V setting is correct for

most of the UK and Europe.

Product specificaties

Merk:	M-Audio
Categorie:	Monitor
Model:	BX8 D3
Kleur van het product:	Zwart
Ingebouwd display:	Nee
Gewicht:	10500 g
Breedte:	250 mm
Diepte:	302 mm
Hoogte:	384 mm
LED-indicatoren:	Ja
Connectiviteitstechnologie:	Bedraad
Ingebouwde luidsprekers:	Ja
Gemiddeld vermogen:	150 W
Aanbevolen gebruik:	Studio
Impedantie:	10 Ohm
Audio-uitgangskanalen:	- kanalen
Speaker plaatsing:	Vloer
Aantal drivers:	2
Woofer:	Ja
Frequentiebereik:	37 - 22000 Hz
Gevoeligheid:	12 dB
Signaal/ruis-verhouding:	114 dB
Luidspreker soort:	2-weg
Versterker:	Ingebouwd
Diameter woofer:	8 "
Diameter hogetonenluidspreker:	1.25 "
XLR in:	Ja
Tweeter:	Ja
AC-ingangsspanning:	220-240 V
AC-ingangsfrequentie:	50 - 60 Hz
Crossover frequentie:	2000 Hz
Versterker/ontvanger ingang interface type:	XLR
Versterker klasse:	A/B
Line-out Total Harmonic Distortion plus Noise (THD+N) (1kHz):	- procent
Line-in Total Harmonic Distortion plus Noise (THD+N) (1kHz):	- procent
Uitgelijnde evenwichtige ependantie:	10 Ohm
Uitgelijnde onevenwichtige ependantie:	20 Ohm