L.R.Baggs M80 Handleiding
Bekijk gratis de handleiding van L.R.Baggs M80 (6 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 8 mensen en kreeg gemiddeld 4.9 sterren uit 4.5 reviews. Heb je een vraag over L.R.Baggs M80 of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/6
U s e r ’s G u i d e
PAC K AGE CO NT EN TS
One M80 pickup with battery installed
One pre-wired strapjack assembly
One spare battery
One 3/32” Allen wrench
Two spare 3/4” pole pieces
One spare 3/8” pole piece
Two self-stick wire clips
One manual
One warranty card
O V E R V I E W A N D C A U T I O N S
The M80 will t guitars with soundholes larger than 3.55”. Make sure that the M80 will t the guitar properly
before installing the strapjack.
Any woodworking (for instance, drilling the strapjack hole) must be performed by a professional dealer, in-
staller. We do not provide advice or support for home or hobbyist woodworking. Installers: Please read the
instructions carefully before proceeding. We will not be responsible for any damage to the guitar or personal
injury resulting from installation.
S TR A PJAC K I N STA LL AT I O N
Drill a clean 1/2” hole in the tail-block for the strapjack. Remove dust & debris from inside the guitar. Remove
the strap ring, retaining nut and one washer from the end of the jack. Bring the jack through the pre-drilled
hole in the tail-block. Using the internal nut, set the proper
depth that will allow the entire smaller threaded section to
protrude from the instrument (see gure 1).
With the jack in place, lay the remaining washer over the
threads and attach the external retaining nut until it’s tight.
Finish by attaching the strap ring. Asserting too much
pressure may crack the nish.
P ICK UP I NS TAL LAT ION
Connect the strapjack to the pickup with the 1/8” plug. Loosen the clamp screws on either end of the M80 until
the clamps are open enough to accommodate the soundboard thickness. Slide the pickup into the guitar’s
soundhole up towards the neck and tighten the screws. Secure the wire with the clips provided. Carefully
tighten the screws until the M80 is snug. If you are concerned about the possibility of the M80 damaging your
guitar’s nish, consider applying thin cork pads (not included) between the clamps and guitar. The clamps
have been left unpadded to improve coupling between the pickup and guitar body. Because the M80 picks
up body vibrations, padding could have some a ect on the pickup’s responsiveness.
Fig. 1
tail-block
Product specificaties
| Merk: | L.R.Baggs |
| Categorie: | Niet gecategoriseerd |
| Model: | M80 |
Heb je hulp nodig?
Als je hulp nodig hebt met L.R.Baggs M80 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd L.R.Baggs
25 Juli 2023
25 Juli 2023
25 Juli 2023
25 Juli 2023
25 Juli 2023
25 Juli 2023
25 Juli 2023
17 Juli 2023
17 Juli 2023
17 Juli 2023
Handleiding Niet gecategoriseerd
- Sloan
- Vermona Modular
- Feelworld
- Quigg
- Laplink
- Martin
- K&M
- Giordani
- Vinotemp
- Crosley
- Minkels
- Eventide
- Guzzanti
- Flir
- Suprema
Nieuwste handleidingen voor Niet gecategoriseerd
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
18 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025
17 Juni 2025