Logilink AVM365 Handleiding

Logilink Bewakingscamera AVM365

Lees hieronder de 📖 handleiding in het Nederlandse voor Logilink AVM365 (4 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

1. Paste the installation sticker

supplied with this camera to

where to install the camera,

and position the four holes for

screws.

Drill the two screws at top to

the wall. ( and as shown

in the picture )

454Z

m565_365a_V1.0

2Prerequisite

Prerequisite (continued)

Before configuring network setup with iPhone / iPad, make

sure you have checked the followings:

(Recommended) Apply your own ADSL or cable

Internet service to simplify the network configurations.

Your camera is connected to your wireless router with

a RJ45 network cable, and it’s powered on.

You have installed our mobile program,

EagleEyes-Lite EagleEyes-Plus or , on your iPhone or

iPad.

iPhone / iPad

Network

Cable

(RJ45)

Wireless

Router

Modem

Camera

LAN Port WAN Port

Event Trigger

System Install the Camera

2. 161

Step4: Select “Apply” to confirm all your changes, and you see the message “Done” or “Fail” in “Status”.WAIT till

Done

Fail

Step6: Open your web browser on iPhone, and enter the IP address of your wireless router (“ ” in 192.168.2.161

our example) to access.

Step3: Select the IP address to enter the setting page, and switch the tab from “DHCP” to “Static”.

Then, note down the IP address and port number you see here. You’ll need them in Step 7.

Step5: In the new device page, give a meaningful name for this connection in “Title”, and select “Save”.

3Configure with iPhone / iPad

Step1: Connect your iPhone / iPad to the wireless router

which has the camera connected.

iPhone / iPad

Network

Cable

(RJ45)

Wireless

Router

Modem

Camera

LAN Port WAN Port

Step2: Open “EagleEyes-Lite” (or “EagleEyes-Plus”),

and click “+” to enter the new device page.

Then, select “Local Network Search” to search

your network camera.

The IP address shown is the address assigned to

your camera by your router.

You have checked the IP address used by your wireless

router as instructed below, and written them down.

You will need them later.

Connect your iPhone / iPad to the wireless router

with the camera connected, and go to “Settings”



“Wi-Fi”. Select “>” near the selected wireless network

to enter the details.

(Optional) Your wireless router supports UPnP, and

this function is enabled.

Note: Please leave some space between the

screws and wall. Do not get them to the end.

2. Hang the camera at the

screws you just fixed, and

make sure the camera

stays in place. Decide the

cable direction (up

/ down) before you fasten

the screws tight to the wall.

3. Drill the rest of screws ( and as shown in the

picture ) into the wall. After that, make sure all

screws are fastened.

4. Adjust the angle of the camera (up / down / left /

right) with the supplied wrenches for better viewing.

a.b.

Q1: I can’t connect to this camera with 3G network, but it works with my wireless network. Why?

A1: Your network conﬁguration is not yet completed. Please set port forwarding as instructed in “3. Conﬁgure with iPhone /

iPad” (Step7 ~ 8).

Q2: My live images are not ﬂuent. Why?

A2: Image ﬂuency could be aﬀected by the local network upload bandwidth, router eﬃciency, client network download

bandwidth, complexity of live view, and more.

(Recommended) To have the best image ﬂuency, select QVGA; to have the best image quality, select “SXGA”; to have

normal image ﬂuency and quality, select “VGA”.

Q&AEagleEyes Operation

4Check Your Connection

Tool Bar

Setting

Info

The ﬁrst two buttons from the left are used for the address book, and the other two are special buttons.

Select to learn more about how to use EagleEyes, where to ﬁnd video demo, and join our Facebook.

Conﬁgures EagleEyes-related parameters.

Conﬁguration Select to enter the camera conﬁguration page to change some camera parameters.

Start to enter :EagleEyes Address Book

Select the connection set to enter :Live View & Control









When you complete the network setup, check your

connection as instructed below.

Step1: Switch your network mode to 3G mode on

iPhone or iPad.

Step2: Start , and select the connection you EagleEyes

just added to see if you can access your

camera successfully.

Step3: Switch your network mode to wireless mode on

iPhone or iPad.

Step4: Start , and add a new connection with EagleEyes

the IP address (e.g. 192.168.2.161) and port

number (e.g. 88) you set in Step3 of “3. Conﬁgure

with iPhone / iPad”. Then, see if you can access

your camera with this new conection successfully.

5Change Default Account

To ensure your account safety, after ﬁnishing

network setup, please access the camera, and

select “ “  “Advance Setup”  “Account” to

change the default user name and password with

new one you prefer.

Q3: The live video keeps ﬂickering. Why?

A3: Please try adjusting the power line frequency to “60 Hz” or “50 Hz” from your iPhone by selecting “ ” to enter IPCAM

Conﬁguration page. Then, go to “Advance Setup”  “Camera” to change setting.

POE Connection (1.3 mega model only)

POE connection is available only when your router or

hub supports this function.

If your router or hub doesn’t support POE connection, you

need to additionally purchase a POE connector. Please

check with your installer or reseller for more details.

POE Router / Hub

Power

Network

Cable

Network

Cable

Factory Default Values

admin

IP Address

Port Number

192.168.1.10

User Name

Password

Cable Overview

Power cable

RJ45 network cable

RESET (Red)

GND (Black)

Alarm-out (Pink)

Alarm-in (Yellow)

GND (Brown)

* iPad ®

& iPhone® are the registered trademarks of Apple Inc.







Live View & Control ConﬁgurationAddress Book

Package Content

Camera Screws &

Wall Plugs

Wrenches Quick Setup

443Z

m365a_V0.9

Event Trigger

System



The naming of port forwarding or virtual server

may vary based on di erent router brands. To ﬀ

know where it is, please refer to the user manual of

your wireless router.

Then, enter the IP address and port number you set

for the camera in Step3, and enable this rule.

Step7: Go to the port forwarding (or virtual server) rule

conﬁguration page.

PORT

FORWARDING

ADVANCED

2. 161

3Continued from the

Merk:	Logilink
Categorie:	Bewakingscamera
Model:	AVM365
Kleur van het product:	Grijs
Breedte:	117.9 mm
Diepte:	287.4 mm
Hoogte:	212.63 mm
Soort:	IP-beveiligingscamera
Gebruikershandleiding:	Ja
Internationale veiligheidscode (IP):	IP67
Ondersteunde videoformaten:	H.264, M-JPEG, MPEG4
GPS:	Ja
Vormfactor:	Rond
Ondersteuning voor plaatsing:	Buiten
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Ja
Montagewijze:	Plafond/muur
Ondersteunde video-modi:	720p
Maximum resolutie:	- Pixels
Type stroombron:	Power over Ethernet (PoE)
Stroomuitvoer (volt):	+12V
Stroomuitvoer (ampère):	1.5 A
Minimale belichting:	0.1 Lux
Field of view (FOV) hoek:	62.7 °
Nachtvisie:	Ja
LED-type:	IR
Vaste focale lengte:	3.8 mm
Formaat analoog signaal:	NTSC, PAL
Omvang optische sensor:	1/4 "
Optische zoom:	- x
Camera sluitertijd:	1/10000 s
Witbalans:	Auto
Bekabelingstechnologie:	10/100Base-T(X)
Ondersteunde netwerkprotocollen:	DDNS / PPPoE / DHCP / NTP / SNTP / TCP/IP / ICMP / SMTP / FTP / HTTP / RTP / RTSP / UPnP / RTCP / IPv4 / Bonjour / DNS / UDP / IGMP / QoS
IP-adresfilter:	Nee
Signaal/ruis-verhouding:	48 dB
Power over Ethernet (PoE):	Ja
PTZ control:	Ja
Dag/nacht modus:	Ja
Minimale RAM:	256 MB
Aantal verlichtingen LEDS:	45
Alarm ingang/uitgang:	Ja
Bedrijfstemperatuur (T-T):	-20 - 40 °C