Liftmaster LMRRUL Handleiding

Liftmaster Niet gecategoriseerd LMRRUL

Lees hieronder de 📖 handleiding in het Nederlandse voor Liftmaster LMRRUL (16 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16

Introduction

The LiftMaster® Retro-Reﬂ ective Photoelectric

Sensor provides non-contact monitored entrapment

protection. For use with LiftMaster® UL Listed

gate operators. The sensor is a UL Recognized

Component and meets UL 325 requirements.

Monitored external entrapment protection devices

MUST be installed at each Entrapment Zone. Refer to

gate operator manual for compatibility with LMRRUL

sensor.

Speciﬁ cations

Max Range: 50 ft. (15.2 m)

Sensor Dimensions with Hood:

2.29" W x 3.72" H x 2.76" D

Reﬂ ector Dimensions with Hood:

2.61" W x 4.72" H x 2" D

Cable Length: 10 ft. (3 m)

Operating Temperature: -40˚C to 65˚C

(-40˚F a 149˚F)

Outdoor Rating: Nema 4X

Input voltage:

Sensor: Black/red wires 6.8 VDC, 20mA

Heater: Green/white wires 10-40VDC or 8-28 VAC, 2

watts max., 170mA @ 12 VDC/VAC,

85mA@ 24 VDC/VAC

Heater: Thermostatically controlled, NOT

recommended for solar applications

MONITORED RETRO-REFLECTIVE

PHOTOELECTRIC SENSOR

Model LMRRUL

To prevent possible SERIOUS INJURY or DEATH from a closing gate or door:

• Read and follow ALL instructions.

• Be sure to DISCONNECT ALL POWER to the operator BEFORE installing the photoelectric sensor.

• The gate or door MUST be in the fully opened or closed position BEFORE installing the LiftMaster®

Monitored Entrapment Protection device.

• Correctly connect and align the photoelectric sensor.

• Install the photoelectric sensor so that the center of the sensor window is NO HIGHER than

4-1/2" (11.4cm) above the ﬂ oor for door operators and 26" (66 cm) above grade for gate operators.

• Monitored external entrapment protection devices MUST be installed per the operator installation

manual at each Entrapment Zone.

• The sensor and reﬂ ector MUST be mounted vertically.

• Use the provided reﬂ ector ONLY.

• Test the gate operator and ALL photoelectric sensors monthly. Replace ANY damaged devices.

• SAVE THESE INSTRUCTIONS.

WARNING: This product can expose you to chemicals including lead, which are known

to the State of California to cause cancer or birth defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov.

Installation

IMPORTANT: The sensor and the reﬂ ector MUST be mounted vertically. Disconnect ALL power to the

operator.

1. Attach the mounting bracket to the post with 1/4"-20 screws. Drill a hole in the post through the center

hole in the bracket. Optional: If installing to a square post or ﬂ at surface, you may attach the sensor

bracket directly to the post without using the mounting bracket. Make sure the location of the sensor

follows the speciﬁ ed measurements. If installing multiple sensors in close proximity, mount the sensors on

opposite sides to avoid crosstalk.

2. Slide the bottom sensor bracket onto the studs of the mounting bracket and secure with 1/4"-20 lock nuts.

Make sure the bracket legs are facing down.

3. Loosely attach the top sensor bracket with 10-32x1" thread-locking screws. Make sure the slots are

facing up.

4. Place the sensor in the bracket and tighten the screws just enough to allow the sensor to rotate inside the

bracket.

5. Slide the hood over the sensor until it snaps into place. Secure hood with the M3 screw. The hood MUST

be installed on the sensor.

6. Route wires through the center hole of the mounting bracket and into the post. Optional: Use conduit with

NEMA 4X compatible 1/2"-14 NPT ﬁ tting (not provided).

7. Place the reﬂ ector in the reﬂ ector hood.

8. Secure the reﬂ ector and hood to the bracket with 8-32x1" screws. Secure the bottom of the reﬂ ector to the

hood with 8-32x1" screws.

9. Mount the reﬂ ector a minimum of 3 ft. (.9 m) and maximum of 50 ft. (15.2 m) away from the sensor.

Carton Inventory

• Photoelectric sensor with hood

and bracket

• Reﬂ ector with hood and

bracket

• Wire cover

• Screws 8-32x1" (4)

• Lock nuts 8-32 (4)

• Screws 8-32x3/8" (2)

• Thread-locking screws

10-32x1" (2)

• Screws 1/4"-20x1-1/4" (6)

• Lock nuts 1/4"-20 (2)

• M3 screw (1)

• Set screw 10-32x3/8" (1)

Tools Needed

• Philips screwdriver

• 1/8" Allen wrench

• 7/16" socket

• 11/32" socket

• 5/32" Allen key

• 3/32" Allen key

≤ 5" (12.7 cm)

from gate or wall Optional for

square post

Door operators:

4-1/2" (11.4 cm)

Gate operators:

4" (10.2 cm)-26" (66 cm)

Door operators: 4-1/2" (11.4 cm)

Gate operators: 4" (10.2 cm)-26" (66 cm)

≤ 5" (12.7 cm)

from gate or wall

Illustrations are for reference only; your application may look different.

Expansion Board

Black (-)

to COM

Red (+) to EYE

or EYE/EDGE

Control Board

Black (-)

Red (+)

See below

Sensor Wiring

Heater Wiring

See below

For use with battery backup

Green

White

Green

White

Green

White

Green

White

Black (not provided)

OPTION 1

OPTION 2

OPTION 3

Control board

ACCESSORY

POWER ON

Max. draw 500 mA

Expansion board

aux relay

From Sensors

External 12V to 24V DC or AC power

supply (not provided) with adequate

current to power all sensors

AUX RELAY will switch

off during power failure

Set switch for open

or close direction

CLOSE EYES/INTERRUPT

for close direction

OPEN EYES/EDGE for open

direction

Green

White

Control board

ACCESSORY POWER ON

Max. draw 500 mA

From Sensors

Wiring

Sensor wiring (red and black wires): Wire the photoelectric sensors (red [+] and black [-] wires) to the

appropriate inputs on the operator or expansion board as shown.

Heater wiring (green and white wires):

• OPTION 1 - Connect to the ACCESSORY POWER ON terminal on the control board (NOT polarity speciﬁ c).

• OPTION 2 - Connect to an external 12V to 24V DC or AC power supply (not provided) with adequate current

to power all sensors.

• OPTION 3 - For use with battery backup. Connect to ACCESSORY POWER ON and AUX RELAY terminals.

Set AUX RELAY switches as shown. In this conﬁ guration, the heater will switch off during a power failure to

extend the battery life.

DO NOT overload the accessory power output on the control board or the external power supply.

NOTE: Heater feature is not recommended for ANY solar installations.

Product specificaties

Merk:	Liftmaster
Categorie:	Niet gecategoriseerd
Model:	LMRRUL

Heb je hulp nodig?

Als je hulp nodig hebt met Liftmaster LMRRUL stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Liftmaster

Liftmaster CAPXSHOOD Handleiding

8 December 2023

Liftmaster 041DJ003MC Handleiding

17 Augustus 2023

Liftmaster myQ-SGC2WCH Handleiding

9 Juli 2023

Liftmaster CAPXS Handleiding

9 Juli 2023

Liftmaster 041D8006-1 Handleiding

9 Juli 2023

Liftmaster IHSL24UL Handleiding

9 Juli 2023

Liftmaster LJ8900W Handleiding

9 Juli 2023

Liftmaster MGJ5011U Handleiding

8 Juli 2023

Liftmaster 041A7767 Handleiding

8 Juli 2023

Liftmaster 41K4629 Handleiding

8 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive IAN 327221 Handleiding

1 Mei 2024

Samsung UN32J4001AF Handleiding

1 Mei 2024

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024