Konstant Lab M2S Handleiding

Konstant Lab Niet gecategoriseerd M2S

Lees hieronder de đź“– handleiding in het Nederlandse voor Konstant Lab M2S (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
M2S
Mono to Stereo? or Stereo to Mono? …both way!
M2S is passive eurorack module. You can convert signal from two mono
channels to stereo jack (or backwards). M2S can be also used like passive stereo
output module. Two mono signals can be connected in to R and L jacks. Then you
can connect headphones or cable to active loudspeakers to stereo output. M2S can
also make “stereo” signal from one mono signal. If you connect only one mono signal
to L(MONO) jack, copy of this signal will be on both L and R signals on STEREO
output.
There are two independent sections in one M2S module. Both sections can
work in various working modes. Modes are switched by Switch* on bottom side.
Section 2 with protection resistors in L and R channel is suitable to mix both channels
in stereo signal to one MONO signal.
1=2 mode – in this mode is 1L (mono) channel shared also to section 2. 1L
(mono) input is copied to both stereo outputs. In case of connection of second mono
signal to 2L (MONO) jack, sharing of 1L signal will be cut. If you do not want to cut
this sharing you have to connect solder jumper J1** with solder iron and solder wire
(just solder two points together). When jumper J1** is connected and you insert
stereo signal in to 2 STEREO jack, L and R channels will be joined to one mono
signal and will be shared to both L(MONO) jacks.
1x2 mode – This mode provides two separated sections: mono to stereo or
stereo to mono sections. There is no connection between section 1 and 2. For mixing
L and R stereo channels use primary section 2.
M2S doesn’t require any power – it is passive module.
www.konstantlab.audio
info@konstantlab.audio
www.konstantlab.audio
info@konstantlab.audio
Switch*
Specs
Power: 0mA
Wide: 2HP
Depth: 15mm
Accessories:
2 screws
2 washers
Jumper J1**

Product specificaties

Merk: Konstant Lab
Categorie: Niet gecategoriseerd
Model: M2S

Heb je hulp nodig?

Als je hulp nodig hebt met Konstant Lab M2S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Konstant Lab

Konstant Lab

Konstant Lab Mult9 Handleiding

14 Augustus 2023
Konstant Lab

Konstant Lab M2S Handleiding

14 Augustus 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive

Playtive IAN 327221 Handleiding

1 Mei 2024
Samsung

Samsung UN32J4001AF Handleiding

1 Mei 2024
Bauknecht

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024
Fakir

Fakir Artemis TS 150 Handleiding

26 April 2024
Sony

Sony UTX-M03 Handleiding

26 April 2024
Sony

Sony URX-P03 Handleiding

26 April 2024
Sony

Sony WRU-806B Handleiding

26 April 2024
Sony

Sony UTX-B03 Handleiding

26 April 2024
Sony

Sony UTX-P03 Handleiding

26 April 2024
Sony

Sony ODS-L10 Handleiding

26 April 2024