Klipsch CP6 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Klipsch CP6 (19 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/19
CP SERIES
OWNER’S MANUAL
RECOMMENDED RECEIVER/AMPLIFIER POWER TO USE WITH KLIPSCH CP SPEAKERS
A speaker can be damaged just as easily with too little power as
with too much power. A general rule is when you raise the volume
level on a receiver/ampliïŹer past the “one half” (or “12 o’clock”
position with a marked volume knob), that receiver/ampliïŹer is now
starting to work beyond its capabilities, sending harmful distortion
that can damage any speaker, no matter how many watts that
speaker is rated to accept. This is true for any speaker and receiver/
ampliïŹer combination. The recommended wattage to use on your
new Klipsch CP speaker depends on which one you have you have:
CP-4: up to 50 watts continuous (for an extended period of time);
200 watt “peaks” (very short bursts/surges)
CP-6: up to 75 watts continuous (for an extended period of time);
300 watt “peaks” (very short bursts/surges)
HOOKING SPEAKERS UP TO AN AMPLIFIER/RECEIVER
When connecting speakers to an ampliïŹer/receiver, always
make sure speaker polarity is correct and the best sound is
obtained by connecting amp/receiver positive (+) to speaker
positive (+) and amp/receiver negative (-) to speaker negative
(-). The CP speaker terminals are designed to accept up to 16
gauge wire.
One pair of Klipsch CP Series speakers, 8 Ohms, can connect to
the left/right speaker terminals of any 8 Ohm rated ampliïŹer/
receiver as shown:
+
-+
-+
-
+
-
ONE PAIR TO
8 CAPABLEΩ
AMP/RECEIVER
Right Channel Left Channel
IF YOU WISH TO USE TWO PAIRS OF KLIPSCH CP
SERIES SPEAKERS ON ONE AMPLIFIER/RECEIVER
WE RECOMMEND ONE OF TWO METHODS:
Method 1 (Preferred): IF your amp/receiver has both A
and B speaker terminals, connect one pair to A and one
to B. Depending on your amp/receiver’s capability you
can then either play Speaker pairs A and B together or
separately or Speaker pair A OR Speaker pair B only.
Method 2: IF YOUR AMP/RECEIVER IS RATED TO 4
OHMS OR LESS make a parallel wire connection as shown
from the amp/receiver’s right and left speaker terminals.
Your amp/receiver may output more power to the
speakers this way (check amp/receiver speciïŹcations).
OTHER POSSIBLE SPEAKER CONNECTION OPTIONS:
Series Wiring of Two Pairs to one Amp/Receiver:
Instead
of a parallel connection using a series connection as
shown has the amp/receiver work at 16 Ohms but this cuts
the power going to each of the speakers usually in half.
If you are using a surround (7/9/11 channel) receiver
that receiver MIGHT allow connection of an additional
pair of speakers to unused surround channels for use in a
different listening area or may have a “Zone 2” capability
to connect those speakers (check your receiver manual)
Using an outboard speaker switcher:
Several types of
available selector boxes allow hookup of multiple pairs
of speakers to one ampliïŹer/receiver and allow switching
between them. Some models allow simultaneous play of two
pairs of speakers. (see your audio dealer for availability).
+
-
+
-+
-+
-+
-
+
-
PARALLEL WIRING TWO PAIRS TO
4 CAPABLE AMP/RECEIVERΩ
Right Channels Left Channels
HOOKING SPEAKERS UP TO AN AMPLIFIER/RECEIVER (CONTINUED)
R
+
L
+
__
R
+
L
+
__
SPK A SPK B
Amp/Receiver Rear Amp/Receiver Front
SPK A SPK B
+
-
+
-+
-+
-+
-
+
-
SERIES WIRING TWO PAIRS TO
16 CAPABLE AMP/RECEIVERΩ
Right Channels Left Channels
METHOD 2
METHOD 1
SERIES WIRING OF TWO PAIRS
TO ONE AMP/RECEIVER


Product specificaties

Merk: Klipsch
Categorie: Speaker
Model: CP6

Heb je hulp nodig?

Als je hulp nodig hebt met Klipsch CP6 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker Klipsch

Handleiding Speaker

Nieuwste handleidingen voor Speaker