KitchenAid KVWC958JSS Handleiding

Bekijk gratis de handleiding van KitchenAid KVWC958JSS (2 pagina’s), behorend tot de categorie Afzuigkap. Deze gids werd als nuttig beoordeeld door 63 mensen en kreeg gemiddeld 4.7 sterren uit 9 reviews. Heb je een vraag over KitchenAid KVWC958JSS of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Range Hood - 36" (91.4 cm) and 48" (121.9 cm)

PRODUCT MODEL NUMBERS

KXW9736Y KXW9748Y

Because Whirlpool Corporation policy includes a continuous commitment to improve

our products, we reserve the right to change materials and specifications without notice.

Dimensions are for planning purposes only. For complete details, see Installation

Instructions packed with product. Specifications subject to change without notice.

Ref. W10331009C

1/31/2012

CABINET OPENING DIMENSIONS

IMPORTANT:

Minimum distance “X”: 24" (61 cm) from electric cooking surfaces

Minimum distance “X”: 30" (76.2 cm) from gas cooking surfaces

The chimneys can be adjusted for different ceiling heights. See the

following chart.

Vented Installations

Min. ceiling heightMax. ceiling height

Electric cooking surface 7' 9" (2.36 m) 10' 2" (3.1 m)

Gas cooking surface 8' 3" (2.51 m) 10' 2" (3.1 m)

*NOTE: The range hood chimneys are adjustable and designed to meet

varying ceiling or soffit heights depending on the distance “X”

between the bottom of the range hood and the cooking surface. For

higher ceilings, an Extension Kit Part Number W10352733 is

available from your dealer or an authorized parts distributor. The

chimney extension replaces the upper chimney shipped with the range

hood.

PRODUCT DIMENSIONS

Vented Installations

36" (91.4 cm)

or 48" (121.9 cm)25" (63.5 cm)

7⁷⁄₈ " (20.0 cm)

11" (28.7 cm)⁵⁄₁₆

32" (82.2 cm) min.³⁄₈

50¹¹⁄₁₆" (128.7 cm) max.

22" (57.8 cm)³⁄₄

VENTING REQUIREMENTS

Page 1 of 2

Electrical Requirements:

●

A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is

required.

●

If the house has aluminum wiring, follow the procedure below:

1. Connect a section of solid copper wire to the pigtail

leads.

2. Connect the aluminum wiring to the added section

of copper wire using special connectors and/or

tools designed and UL listed for joining copper to

aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with local

codes and industry accepted wiring practices.

18" (45.7 cm) min.

clearance upper

cabinet to countertop

X*

36" (91.4 cm)

countertop height

See Note*

36" (91.4 cm) or 48" (121.9 cm)

or cabinet opening width

(if installed between cabinets)

● Vent system must terminate to the outdoors.

● Do not terminate the vent system in an attic or other enclosed area.

● Do not use 4" (10.2 cm) laundry-type wall caps.

● Use metal vent only. Rigid metal vent is recommended. Plastic or metal foil

vent is not recommended.

● The length of vent system and number of elbows should be kept to a

minimum to provide efficient performance.

For the most efficient and quiet operation:

● Use no more than three 90° elbows.

● Make sure there is a minimum of 24" (61.0 cm) of straight vent between the

elbows if more than 1 elbow is used.

● Do not install 2 elbows together.

● Use clamps to seal all joints in the vent system.

● The vent system must have a damper. If the roof or wall cap has a damper,

do not use the damper supplied with the range hood.

● Use caulking to seal exterior wall or roof opening around the cap.

● The size of the vent should be uniform.

Venting Methods

Typical Internal Blower Motor System Venting Installations

A 10" (25.4 cm) round vent system is needed for installation (not included).

The range hood exhaust opening is 10" (25.4 cm) round.

NOTE: Flexible vent is not recommended. Flexible vent creates back pressure

and air turbulence that greatly reduce performance.

Product specificaties