Kicker SubStage SSON12 Handleiding

Kicker Subwoofer SubStage SSON12

Lees hieronder de 📖 handleiding in het Nederlandse voor Kicker SubStage SSON12 (10 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/10
1
SSON12
Designed for 2012 and newer Chevrolet® Sonic vehicles
©2012 Stillwater Designs
SSON12-A2-20121010
2
Subwoofer Assembly
Subwoofer
Power Harness
25A Fuse
Wire Ties x6
Foam Strip
Wire Taps x2
Adapter Harness
Subwoofer Body
Harness
3
Power Wire Routing
1. Disconnect the negative battery cable from the battery.
2. Using a razor knife make a cross shaped incision in the large rubber grommet from inside the vehicle and
feed the power wire from the engine compartment to the cabin. Using a fi sh tape wire is recommended.
Fig. 1
NOTE: If you are installing the optional amplifi er system, install the power wire for it at this time.
3. Pull the wire(s) through the grommet until the sheathing touches the grommet.
4. Remove the fuse box cover under the hood. Remove the fuse from the fuse holder on the subwoofer
power wire and connect the power wire to the accessory lug. Torque to 9 +/- 1.5 Nm. Make sure that the
wires exit on the side closest to the battery. Fig. 2
5. Install the connecter on the end of the power harness inside the cabin. The black connecter should have
a block out plug installed in one side to prevent the power wire from being inserted into the wrong position in
the connecter.
NOTE: If you are installing the optional amplifi er system, it does not matter what order the three wires are
installed on the three-pin connecter, but the terminals can only be inserted one way. If the terminal will not
go into the connecter, simply turn it 180 degrees and try again. Push the terminals in until they click and lock
into place.
Body Harness Routing
6. Remove the driver’s side kick/threshold panel by loosening the
retainer at the top and then pulling loose. Fig. 3
7. Remove the lower portion of the rear seat by pulling straight up
on the front edge.
8. Snap loose the rear drivers side threshold panel located along
the bottom of the door opening.
9. Snap loose the lower portion of the B pillar post cover.
Cut grommet here.
Fig. 1
Fig. 2
Wires should exit in
direction of arrow
Retainer – Rotate
counter-clockwise
Fig. 3
Remember to place your warranty card in the glove box for future use.

Product specificaties

Merk: Kicker
Categorie: Subwoofer
Model: SubStage SSON12

Heb je hulp nodig?

Als je hulp nodig hebt met Kicker SubStage SSON12 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Subwoofer Kicker

Kicker

Kicker 48CVTDF122 Handleiding

3 Juli 2023
Kicker

Kicker 48DCWR102 Handleiding

29 Juni 2023
Kicker

Kicker 48CWR82 Handleiding

28 Juni 2023
Kicker

Kicker 48DCWR122 Handleiding

26 Juni 2023
Kicker

Kicker C104 Handleiding

16 Juni 2023
Kicker

Kicker Hideaway HS10 Handleiding

15 Mei 2023
Kicker

Kicker 48TCWRT672 Handleiding

13 Mei 2023
Kicker

Kicker 48CWRT84 Handleiding

7 Mei 2023
Kicker

Kicker Q-Class 10L7 Handleiding

4 Mei 2023
Kicker

Kicker Comp Gold 12 Handleiding

4 Mei 2023

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer

RCF

RCF S 19 Handleiding

10 April 2024
RCF

RCF S 29 Handleiding

10 April 2024
KEF

KEF KC92 Handleiding

6 April 2024
Klipsch

Klipsch Reference Premiere RP-1200SW Handleiding

3 April 2024
Klipsch

Klipsch Reference Premiere RP-1000SW Handleiding

3 April 2024
Velodyne

Velodyne Deep Waves 10 Handleiding

27 Maart 2024
Klipsch

Klipsch PRO-1000SW Handleiding

27 Maart 2024
Totem

Totem KIN Sub Handleiding

27 Maart 2024
Velodyne

Velodyne Deep Waves 12 Handleiding

27 Maart 2024
Kanto

Kanto SUB8V Handleiding

27 Maart 2024