Kicker BX360.4 Handleiding

Kicker Receiver BX360.4

Lees hieronder de 📖 handleiding in het Nederlandse voor Kicker BX360.4 (16 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 56 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/16

BX AMPLIFIER

BX360.4

BX500.4

English Version

Deutsche Version

2BX AMPLIFIERS

BX.4-SERIES AMPLIFIERS Owner’s Manual

PERFORMANCE

Authorized KICKER Dealer:

Purchase Date:

Model Number:

Serial Number:

Model: BX360.4 BX500.4

RMS Power, all channels driven

@ 14.4V, 4 stereo, ≤ 1% THD+NΩ

@ 14.4V, 2 stereo, ≤ 1% THD+NΩ

@ 14.4V, 4 mono, ≤ 1% THD+NΩ

60W x 4

90W x 4

180W x 2

80W x 4

125W x 4

250W x 2

Length 335mm 370mm

Speciﬁcations common to all models:

Height 54mm

Width 220mm

Frequency Response ± 1dB 5Hz–60000Hz

Signal-to-noise Ratio >95dB, A-weighted, re: rated power

Input Sensitivity Low Level:

200mV–4V

High Level:

500mV–10V

Selectable Electronic Crossover OFF (bypass) - variable HP, LP | 50–200Hz, 12dB/octave

Bass Boost Variable | 0–12dB @ 40Hz

MODEL: BX360.4 / BX500.4

BX AMPLIFIERS

INSTALLATION

Mounting: Choose a structurally sound location to mount your KICKER ampliﬁer. Avoid any damage of the

vehicle’s components like wires, cables, board computer, seat belts, gastank where the screws be driven.

Ensure that this chosen location provide sufﬁcient air circulation for the ampliﬁer. Do not mount the device into

small or sealed spaces without air circulation near by heat dispersing parts or electrical parts of the vehicle. Do

not mount the ampliﬁer on top of a subwooferbox or any other vibrating parts, thereby parts in the inside of the

ampliﬁer may get loosen. Drill four holes using a 3mm bit and use the supplied screws to mount the ampliﬁer.

Wiring: Disconnect the ground connection of vehicle’s battery to avoid an electrical short. Then, connect the

ground wire to the ampliﬁer. Connect the GROUND terminal with a suitable contact ground point on the vehicle’s

chassis. The ground wire must be as short as possible and must be connected to a blank metallic point at the

vehicle’s chassis. Ensure that this ground point has a stable and safe electric connection to the negative “–”pole

of the battery. Check this ground wire from the battery to the ground point if possible and enforce it, if required.

Adding an additional ground wire of a larger gauge between the battery’s negative post and the vehicle chassis is

recommended.

12V

battery

external fuse

BX360.4 50 A

BX500.4 60 A

remote turn-on

from source unit

bare-metal

chassis ground

≤

30cm

≤

60cm

Install a fuse within 30cm of the battery and in-line with the power cable connected to your ampliﬁer. If you ever

need to remove the ampliﬁer from the vehicle after it has been installed, the ground wire should be the last wire

disconnected from the ampliﬁer-just the opposite as when you installed it.

AMP 2

AMP 1

The BX ampliﬁer has two input sections.

The RCA inputs can process the low

level signals from your car stereo’s

source unit. The HI LEVEL INPUT is

suitable to connect loudspeaker wires

of your headunit, if your headunit is not

equipped with preampliﬁer RCA outputs.

Keep the audio signal cable away from

factory wiring harnesses and other power

wiring if possible. If you need to cross

this wiring, cross it at a 90 degree angle

if possible.

WARNING: Never use the RCA inputs and the HI LEVEL INPUTS at the same time.

Connect the loudspeaker wires of your vehicle according to the drawing above with the included HI LEVEL

INPUT jack. The ground wire (black) must be connected with the ground of vehicle’s chassis.

Then, plug-in the HI LEVEL INPUT jack into the HI LEVEL INPUT socket.

Product specificaties

Merk:	Kicker
Categorie:	Receiver
Model:	BX360.4
Kleur van het product:	Zwart
Breedte:	335 mm
Diepte:	220 mm
Hoogte:	54 mm
Connectiviteitstechnologie:	Bedraad
Gemiddeld vermogen:	360 W
Audio-uitgangskanalen:	4.0 kanalen
Frequentiebereik:	5 - 60000 Hz
Signaal/ruis-verhouding:	95 dB
Totale harmonische vervorming (THD):	1 procent
Input sensitiviteit:	500 mV
Crossover frequentie:	200 Hz
Piekvermogen per kanaal:	90 W
Versterker klasse:	A/B
RMS vermogen uitvoer per kanaal (4 Ohm):	60 W
Line inputs (RCA):	1
RMS vermogen uitvoer per kanaal (2 Ohm):	90 W
Bass boost:	0 - 12 dB
Ingebouwde crossover:	Ja