Kenwood DNX5120 Handleiding
Kenwood
GPS apparaat
DNX5120
Lees hieronder de 📖 handleiding in het Nederlandse voor Kenwood DNX5120 (33 pagina's) in de categorie GPS apparaat. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/33
© B54-4624-00/00 (KW/K2W)
DNX5120
DNX512EX
GPS NAVIGATION SYSTEM
INSTALLATION MANUAL
SYSTÈME DE NAVIGATION GPS
MANUEL D’INSTALLATION
SISTEMA DE NAVEGACIÓN GPS
MANUAL DE INSTALACIÓN
2 | DNX5120/DNX512EX
Accessories
1
..........1
2
..........1
3
..........2
4
..........1
5
..........1
6
..........6
7
..........6
8
..........1
9
..........1
0
..........1
!
..........1
English | 3
Installation Procedure
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire
connections for each unit.
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
8. Press the reset button.
2WARNING
• If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
Acquiring GPS Signals
The first time you turn on the DNX5120/DNX512EX,
you must wait while the system acquires satellite
signals for the first time. This process could take up to
several minutes. Make sure your vehicle is outdoors
in an open area away from tall buildings and trees for
fastest acquisition. After the system acquires satellites
for the first time, it will acquire satellites quickly each
time thereafter.
¤
• Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting and wiring
work to professionals.
• Make sure to ground the unit to a negative 12V DC power
supply.
• Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
• Do not use your own screws. Use only the screws provided.
If you use the wrong screws, you could damage the unit.
• If the power is not turned ON (“PROTECT” is displayed),
the speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
• If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
• If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
• If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
• Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
• Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
• When only two speakers are being connected to the
system, connect the connectors either to both the front
output terminals or to both the rear output terminals (do
not mix front and rear). For example, if you connect the +
connector of the left speaker to a front output terminal, do
not connect the connector to a rear output terminal.-
• After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
• Mount the unit so that the mounting angle is 30° or less.
• This unit has the cooling fan (page 5) to decrease the
internal temperature. Do not mount the unit in a place
where the cooling fan of the unit are blocked. Blocking
these openings will inhibit the cooling of the internal
temperature and result in malfunction.
• Do not press hard on the panel surface when installing the
unit to the vehicle. Otherwise scars, damage, or failure may
result.
Product specificaties
| Merk: | Kenwood |
| Categorie: | GPS apparaat |
| Model: | DNX5120 |
Heb je hulp nodig?
Als je hulp nodig hebt met Kenwood DNX5120 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding GPS apparaat Kenwood
10 Mei 2023
9 Mei 2023
5 Mei 2023
1 Mei 2023
26 April 2023
16 April 2023
31 Maart 2023
29 Maart 2023
17 Maart 2023
2 Maart 2023
Handleiding GPS apparaat
- GPS apparaat Samsung
- GPS apparaat LG
- GPS apparaat Garmin
- GPS apparaat Pioneer
- GPS apparaat Acer
- GPS apparaat Alpine
- GPS apparaat Audiovox
- GPS apparaat Bushnell
- GPS apparaat Dual
- GPS apparaat Falk
- GPS apparaat First Alert
- GPS apparaat Hitachi
- GPS apparaat Humminbird
- GPS apparaat Kogan
- GPS apparaat Lowrance
- GPS apparaat Magellan
- GPS apparaat Mio
- GPS apparaat Navman
- GPS apparaat Nedis
- GPS apparaat Nedsoft
- GPS apparaat Polar
- GPS apparaat QStarz
- GPS apparaat Renkforce
- GPS apparaat Teasi
- GPS apparaat Teltonika
- GPS apparaat TomTom
- GPS apparaat Uniden
- GPS apparaat Ventus
- GPS apparaat Orbit
- GPS apparaat Celestron
- GPS apparaat Lezyne
- GPS apparaat Hamlet
- GPS apparaat Tile
- GPS apparaat Canyon
- GPS apparaat IFM
- GPS apparaat Coyote
- GPS apparaat Spotter
- GPS apparaat Chipolo
- GPS apparaat Tractive
- GPS apparaat Navilock
- GPS apparaat Tragant
- GPS apparaat Trackilive
- GPS apparaat Avidyne
- GPS apparaat Moki
- GPS apparaat Lantronix
- GPS apparaat LifeWatcher
- GPS apparaat PAJ GPS
Nieuwste handleidingen voor GPS apparaat
11 April 2024
11 April 2024
11 April 2024
11 April 2024
10 April 2024
10 April 2024
10 April 2024
26 Maart 2024
26 Maart 2024
13 Maart 2024