JL Audio Stealthbox SB-F-FLX/10W3v3 Handleiding

JL Audio Niet gecategoriseerd Stealthbox SB-F-FLX/10W3v3

Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio Stealthbox SB-F-FLX/10W3v3 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3

I N S T A L L A T I O N G U I D E

for the

SB-F-FLX/10W3v3

SKU#94451

2009 & Up Ford Flex

Thank you for choosing a JL Audio Stealthbox® for your automotive sound system. With proper installation, your new vehicle-

specific enclosed subwoofer system will deliver years of listening pleasure.

We strongly recommend that you have your new Stealthbox® installed by your authorized JL Audio dealer. The installation

professionals employed by your dealer have the necessary tools and experience to disassemble and reassemble your vehicle

properly. Also, keep in mind that your warranty coverage extends to 2 years if your system is installed or approved by your

authorized JL Audio dealer. If you prefer to perform your own installation, please read this installation guide completely

before beginning the process.

If you choose to perform the installation yourself, it is absolutely vital that

the Stealthbox ® be properly mounted to the vehicle according to these

instructions. Failure to mount the enclosure properly presents two problems:

1) The sub-bass performance will suffer due to the movement of the enclosure

caused by the force exerted by the woofer(s).

2) A loose enclosure presents a serious safety hazard in the event of a collision

or sudden deceleration.

S T E P 1

Empty out the back of the vehicle.

Continued on Next Page

S T E P 2

Remove the passengers side rear door sill.

S T E P 3

Remove the false floor and, the tailgate, and door sill.

SB-F-FLX-10W3v3 INSTR_SKU# 011293

INSTALLATION

D I F F I C U L T Y :

OUT

ESTIMATED TIME:

2-3 HOURS

Continued on Next Page

SB-F-FLX-10W3v3 INSTR_SKU# 011293

S T E P 7

Using a die grinder (or a Dremel® type tool), grind off all of

the plastic welds as shown.

***CAUTION***

Always follow proper safety techniques when using

power tools as described by the tool manufacturer.

S T E P 6

The factory subwoofer grille (as shown) needs to be

removed. This process will be done from the back side of

the panel.

S T E P 5

Remove the OEM subwoofer/amplifier as shown. Run the

wire for the Stealthbox® to this general location (indicated by

arrow), as the Stealthbox® will be mounted here. Leave extra

wire so that you can secure it as desired once the installation

is finished.

S T E P 4

Remove the interior plastic trim panel. You can leave the

sections of the panel that the seat belts go through as

shown.

Page 2 • JL Audio, Inc 2016

S T E P 9

Looking at the panel from the front, trim all of the edges of

the opening leaving a 3/8” flange inside the recess at the top,

and a 1” flange inside the recess at the sides and bottom.

S T E P 1 1

Remove the woofer and stuffing from the Stealthbox, slide

the Stealthbox® into position, mark the two mounting holes

as shown, and remove the enclosure.

S T E P 1 0

Re-install the interior panel along with all of the previously

removed panels. Make sure that you can access the previ-

ously run wire for the Stealthbox®.

S T E P 8

This is the back of the grille completely removed showing all

of the welds that needed to be removed.

3/8”

1”

SB-F-FLX-10W3v3 INSTR_SKU# 011293

S T E P 1 5

C O N G R A T U L A T I O N S !

You have completed the installation for this model!

Enjoy your new Stealthbox®!

Please refer to the Power Recommendation section for an

amplifier recommendation and basic set-up help.

S T E P 1 4

Connect the wire from the amplifier to the Stealthbox®, and

slide the enclosure into place over the two Allen Head Set

Screws installed in . Mount the enclosure using the STEP 13

included Fender Washers, Split lock Washers and, Hex Nuts

as shown. If necessary, use a Allen Wrench to keep the Allen

Head Set Screws from rotating while tightening. Remember

to re-install the stuffing that was removed earlier, and rein-

stall the woofer. Test the system for proper operation. Put all

the stuff back in the vehicle that you took out in STEP 1.

S T E P 1 3

Slide the two Speed Nuts into location with the “Nut” side

towards the outside of the vehicle into position over the two

holes that were just drilled as shown. Install the two 3/8-16

x 2 1/4” Allen Head Set Screw with the Allen Head opening

towards the center of the vehicle.

S T E P 1 2

Using a Unibit® or, a 9/16” drill bit, drill out the two holes

as marked in the previous step. DO NOT DRILL DEEPER

THAN 1/2” or you run the risk of scarring (or penetrating)

the outer sheet metal of the car.

Page 3 • JL Audio, Inc 2016

All specifications are subject to change without notice. “JL Audio®” and the JL Audio logo, “Stealthbox” and the Stealthbox logo are registered

trademarks of JL Audio, Inc. “Ahead of the Curve” and its respective logo is a trademark of JL Audio, Inc.

For more detailed information please visit us online at www.jlaudio.com.

(954) 443-1100

w w w . j l a u d i o . c o m

1 0 3 6 9 N O R T H C O M M E R C E P A R K W A Y • M I R A M A R , F L O R I D A • 3 3 0 2 5 • U S A

I N C L U D E D H A R D W A R E

2) 3/8-16 x 2 1/4” Allen Head Set Screw 2) 3/8-16 Speed Clip

2) 3/8 x 2” Fender Washer 2) 3/8” Split Lock Washer

2) 3/8-16 Hex Nut

S P E C I F I C A T I O N S

Enclosure Type: Acoustic Suspension (sealed)

Driver Type: 10W3v3-2

Nominal Impedance: 2 Ohms

Continuous Power Handling: 500 Watts

P O W E R R E C O M M E N D A T I O N

JL Audio recommends using a high quality amplifier such as the JL Audio XD300/1v2. The diagram below shows

the recommended crossover settings for the XD300/1v2 when being used to power your Stealthbox ®.

The JL Audio XD300/1v2 is a very versatile audio component. Please consult the owner’s manual for even more

detailed information about installing and tuning this amplifier.

M I D / H I G H F R E Q U E N C Y D R I V E R F I T M E N T

A variety of JL Audio coaxial and component systems will fit in the factory speaker locations of you vehicle.

Front Speaker Size / Location: 5”x 7” / 6”x 8”- Front Doors

Fits JL Audio Models: TR570-CXi, C2-570x, C3-570, C5-570, C5-570x & ZR570-CSi

Rear Speaker Size / Location: 5”x 7” / 6”x 8”- Rear Door

Fits JL Audio Models: TR570-CXi, C2-570x, C3-570, C5-570x

Product specificaties

Merk:	JL Audio
Categorie:	Niet gecategoriseerd
Model:	Stealthbox SB-F-FLX/10W3v3

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio Stealthbox SB-F-FLX/10W3v3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd JL Audio

JL Audio MediaMaster MM105-HR Handleiding

11 Maart 2024

JL Audio JLINK RX Handleiding

8 Januari 2024

JL Audio Stealthbox SBA-J-JK-FHB Handleiding

31 Augustus 2023

JL Audio Stealthbox SB-GM-BURBCNSL/10W3v3 Handleiding

31 Augustus 2023

JL Audio Stealthbox SB-F-SUPRDTY/10W1v3 Handleiding

31 Augustus 2023

JL Audio Stealthbox SB-D-QDRAM/10W3v3 Handleiding

31 Augustus 2023

JL Audio Stealthbox SB-GM-C6CONV/8W3v3 Handleiding

31 Augustus 2023

JL Audio Stealthbox SB-J-JL4DDRV/10TW1-4 Handleiding

31 Augustus 2023

JL Audio Stealthbox SB-F-F1502/10W3v3/TN Handleiding

31 Augustus 2023

JL Audio Stealthbox SB-N-350/10W3v3 Handleiding

31 Augustus 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive IAN 327221 Handleiding

1 Mei 2024

Samsung UN32J4001AF Handleiding

1 Mei 2024

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024