JL Audio RD400/4 Handleiding

JL Audio Receiver RD400/4

Lees hieronder de đź“– handleiding in het Nederlandse voor JL Audio RD400/4 (20 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 111 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/20
Thank you for purchasing a JL Audio amplifier for
your automotive sound system.
Your amplifier has been designed and manufactured to exacting
standards in order to ensure years of musical enjoyment in your vehicle.
For maximum performance, we highly recommend that you have
your new amplifier installed by an authorized JL Audio dealer. Your
authorized dealer has the training, expertise and installation equipment
to ensure optimum performance from this product. Should you
decide to install the amplifier yourself, please take the time
to read this manual thoroughly to familiarize yourself
with its installation requirements and setup procedures.
If you have any questions regarding the instructions in this
manual or any aspect of your amplifier’s operation, please contact your
authorized JL Audio dealer for assistance. If you need further assistance,
please call the JL Audio Technical Support Department
at (954) 443–1100 during business hours.
OWNER’S MANUAL
400W 4-Channel Amplier
2 | JL Audio - RD400/4 Owner’s Manual
PROTECT YOUR HEARING!
We value you as a long-term customer. For
that reason, we urge you to practice restraint in
the operation of this product so as not to damage
your hearing and that of others in your vehicle.
Studies have shown that continuous exposure to
high sound pressure levels can lead to permanent
(irreparable) hearing loss. This and all other
high-power amplifiers are capable of producing
such high sound pressure levels when connected
to a speaker system. Please limit your continuous
exposure to high volume levels.
While driving, operate your audio system in
a manner that still allows you to hear necessary
noises to operate your vehicle safely (horns,
sirens, etc.).
SERIAL NUMBER
In the event that your amplifier requires
service or is ever stolen, you will need to have
a record of the product’s serial number. Please
take the time to enter that number in the space
provided below. The serial number can be found
on the bottom panel of the amplifier and on the
amplifier packaging.
Serial Number:
INSTALLATION APPLICATIONS
This amplifier is designed for operation in
vehicles with 12 volt, negative-ground electrical
systems. Use of this product in vehicles with
positive ground and/or voltages other than 12V
may result in damage to the product and will void
the warranty.
This product is not certified or approved for
use in aircraft.
Do not attempt to “bridge” the outputs of this
amplifier with the outputs of a second amplifier,
including an identical one.
WHAT’S INCLUDED
(1) RD400/4 amplifier
(1) Control panel cover (removable)
(1) Round logo badge
(1) 2.5 mm hex wrench
(1) User manual
Left
or
Mono
Right
Only
+12 VDC Ground Remote
Input Mode
2 Ch. | 4 Ch.
Input Voltage
Low
| High
Rem. |
Os et |
Signal
CH. 1
CH. 2
CH. 3
CH. 4
(L
)
(R )
INPUT SECTI ON
Turn On Mode
PRE-OUT S
CH. 3
(L)
CH. 4
(R)
CH. 1
(L)
CHANNELS 1 & 2
CH. 2
(R)
Filter Mode
Filter Freq. (Hz) Filter Freq. (Hz)
O | HP | LP
Filter Mode
O | HP | LP
Input Type Input Sensitivity Input Sensitivity
Stereo
|
Mono
Input Type
Stereo
|
Mono
4 Channel Amplif ier
CHANNELS 3 & 4
Clippi ng
Clippi ng
Status
LED
(pg. 10-11)
Ch. 1 & 2
Clipping
Indicator
(pg. 7-8)
Ch. 3 & 4
Clipping
Indicator
(pg. 8)
Ch. 1 & 2
Filter Mode
Selector
(pg. 8)
Ch. 3 & 4 Filter
Frequency
Selector
(pg. 8)
Ch. 3 & 4
Filter Mode
Selector
(pg. 8)
Ch. 1 & 2
Input Type
(pg. 7)
Ch. 3 & 4
Input Type
(pg. 7)
Input
Mode
(pg. 7)
Input
Voltage
(pg. 7)
Turn-On
Mode
(pg. 6)
Ch. 1 & 2 Input
Sensitivity Control
(pg. 7-8)
Ch. 1 & 2 Filter
Frequency
Selector
(pg. 8)
Ch. 3 & 4 Input
Sensitivity Control
(pg. 7-8)
3
PLANNING YOUR INSTALLATION
It is important that you take the time to
read this manual and that you plan out your
installation carefully. The following are some
considerations that you must take into account
when planning your installation.
Cooling Efficiency Considerations:
The outer shell of your JL Audio amplifier
is designed to remove heat from the amplifier
circuitry. For optimum cooling performance,
this outer shell should be exposed to the
largest possible volume of air. Enclosing the
amplifier in a small, poorly ventilated chamber
can lead to excessive heat build-up and degraded
performance. If an installation calls for an
enclosure around the amplifier, we recommend
that this enclosure be ventilated with the aid
of a fan. In normal applications, fan-cooling is
not necessary.
Mounting the amplifier upside down is
strongly discouraged. If mounting the amplifier
under a seat, make sure there is at least 1 inch
(2.5 cm) of space above the amplifier’s outer shell
to permit proper cooling.
Safety Considerations:
Your amplifier needs to be installed in a dry,
well-ventilated environment and in a manner
which does not interfere with your vehicle’s safety
equipment (air bags, seat belt systems, ABS brake
systems, etc.). You should also take the time to
securely mount the amplifier so that it does not
come loose in the event of a collision or a sudden
jolt to the vehicle.
Stupid Mistakes to Avoid:
• Check before drilling any holes in your vehicle
to make sure that you will not be drilling
through a gas tank, brake line, wiring harness or
other vital vehicle system.
• Do not run system wiring outside or underneath
the vehicle. This is an extremely dangerous
practice which can result in severe damage to
your vehicle and person.
• Protect all system wires from sharp metal edges
and wear by carefully routing them, tying
them down and using grommets and loom
where appropriate.
• Do not mount the amplifier in the engine
compartment, under the vehicle, on the roof or
in any other area that will expose the amplifier
circuitry to the elements.
INPUT SECTION
(L)
(R )
Left
or
Mono
Right
Only
CH. 1&2 CH. 3&4
CH. 3
(L)CH. 4
(R)
CH. 1
(L)CH. 2
(R)
BridgedBridged
Speaker OutputsSpeaker Outputs
PREOUTS
+12 VDC Ground Remote
Remote Turn-On
Connector
(pg. 6)
Chassis Ground
Connector
(pg. 5)
Channels 1 & 2
Input Jacks
(pg. 7)
Left & Right
Output Jacks
(pg. 9)
+12 V Power
Connector
(pg. 5)
Channels 3 & 4
Speaker Outputs
(pg. 9)
Channels 1 & 2
Speaker Outputs
(pg. 9)
Channels 3 & 4
Input Jacks
(pg. 7)


Product specificaties

Merk: JL Audio
Categorie: Receiver
Model: RD400/4

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio RD400/4 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver JL Audio

Handleiding Receiver

Nieuwste handleidingen voor Receiver