JL Audio M-SWMCPv3-1.315 Handleiding

JL Audio Speaker M-SWMCPv3-1.315

Lees hieronder de 📖 handleiding in het Nederlandse voor JL Audio M-SWMCPv3-1.315 (2 pagina's) in de categorie Speaker. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Installation Instructions for
M-SWMCPv3-1.315 M-SWMCPv3-1.660 M-SWMCPv3-1.900
M-SWMCPv3-2.000 M-SWMCPv3-2.250
M-SWMCPv3-2.375 M-SWMCPv3-2.500
P I PE M O UN T I N G F I X T U R E S ( S W I V EL)
FOR ETXv3 ENCLOSED SPEAKER SYSTEMS
LIMITED WARRANTY  MARINE PRODUCTS USA
JL AUDIO warrants this product to be free of defects in materials and workmanship for a period of two (2) years from the
original date of purchase.
This warranty is not transferable and applies only to the original purchaser from an authorized JLAUDIO dealer. Should service
be necessary under this warranty for any reason due to manufacturing defect or malfunction, JL AUDIO will (at its discretion),
repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not
covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions,
unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages
and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not
covered under warranty.
Any applicable implied warranties are limited in duration to the period of the express warranty as provided herein beginning
with the date of the original purchase at retail, and no warranties, whether express or implied, shall apply to this product
thereafter. Some states do not allow limitations on implied warranties, therefore these exclusions may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
For Service Information in the U.S.A. please call
JL Audio Customer Service: (954) 443-1100
9:00 AM – 5:30 PM (Eastern Time Zone)
JL Audio, Inc
10369 North Commerce Pkwy.
Miramar, FL 33025, USA
International Warranties:
Products purchased outside the United States of America are covered only
by that country’s distributor and not by JL Audio, Inc.
w w w . j l a u d i o . c o m
JL Audi and the JL Audio logo are regist ered tr adem arks of JL Audio, Inc. “Ahead of the Cu rve” and its respe ctive logo is a t rademark of JL Audio, In c.
©2014 JLAudio, Inc. • For more detailed inf ormation please visit us onl ine at Due to our policy of continu ous product development, all specifications are subject to change without notice. www.jlaudio.com.
SKU# 011429
Printed in U.S.A. • 040815
For best adhesion, it is recommended to clean the inside
of the aluminum cap with acetone (not included), prior
to attaching it to the speaker enclosure. Apply a circular
bead of silicone adhesive (included) to the inside of the
aluminum logo cap, about 1/2-inch (13 mm) from the
outer edge.
17
Align the aluminum logo cap to the desired angle of
rotation, and press it onto the back of the enclosure.
Apply masking tape (not included) to hold the cap in
place until the silicone cures (at least 24 hours).
18
Remove adhesive backing and install the JL Audio logo
badge (Sport Grille Models Only).
13
If a dierent speaker angle is desired, remove the speaker
mounting screws and washers.
14
Rotate the enclosure to the desired angle, install the
5/16 - 18 x 1/2” set screw into the base of the xture, and
fully tighten.
16
Rotate the speaker to the desired angle. Reinstall the
speaker and speaker mounting screws and washers.
Hand-tighten the screws in a criss-cross pattern.
15
Have a helper support the enclosure during this step.
Use the supplied butt connectors to connect the red (+)
and black (-) speaker cable exiting the ETXv3 enclosure
to the speaker cable exiting the pipe. e green and white
wires will not be used in this application.
9
Adjust the angle of the xture until level, mark the
location for the speaker cable hole. Remove the xture
assembly, and drill a 1/2” hole on the mark.
5
Align the two upper halves of the xture around the pipe.
Hand-tighten four 1/4 - 20 x 1-1/4” machine screws with
1/4” lock washers into the xture. DO NOT TIGHTEN
FULLY AT THIS POINT.
11
Compress the base and two upper halves of the xture
together while pushing the fork out through the small
pin holes on the opposite side. Flip the fork, and
reinstall, along with the two #8 - 32 x 3/8” machine
screws and lock washers.
3
Remove the four 1/4 - 20 x 1-1/4” machine screws and
1/4” lock washers to separate the two upper halves of
the xture. Pass the speaker cable exiting the enclosure
through the opening on the underside of the xture.
7
Slide the excess speaker cable and the butt connectors
into the opening in the pipe as you raise the enclosure to
ush the xture to the pipe.
10
In applications that require the logo to be inverted,
remove the two #8 -32 x 3/8” machine screws and lock
washers.
2
For applications where the cable cannot be routed
through the pipe, the cable can be passed through one of
the openings on the side of the xture.
6
Remove one of the 1/4 - 20 x 1-1/4” machine screws
and 1/4” lock washers at a time. Apply Loctite® red
thread-locking compound (included), reinstall, and fully
tighten. Repeat the same process for the other three
screws. (Continued on reverse.)
12
Determine the speaker mounting location, and
temporarily secure the xture around the pipe by hand
tightening the four 1/4 - 20 x 1-1/4” machine screws and
1/4” lock washers.
4
Apply Loctite® red thread-locking compound
(included) to two 5/16” - 18 x 1-1/4” machine screws
(included), thread them into the base of the xture, and
push down on the xture to ensure no gap while fully
tightening.
8
Be sure the indicated stopping points are on opposite
sides of the xture as shown. e enclosure can rotate
up to 205.5 degrees in the clockwise direction, and 128.5
degrees in the counter-clockwise direction.
1
128.5 205.5
IMPORTANT: Swivel mounting xtures should only be
attached to horizontal pipes. ETXv3 enclosures should
only be mounted directly above (12 Oclock position) or
directly below (6 O’clock position) a horizontal pipe.
NOTE: The M-SWMCPv3-2.000 fixture and
M770-ETXv3-SG-WH Enclosed Speaker
System are used in this manual for illustrative
purposes only. The fixture installation steps
are the same for all ETXv3 Enclosed Speaker
Systems and all M-SWMCPv3 Swivel-Mount
Fixtures listed on front cover.
WARNING: Do not mount enclosures to a horizontal
pipe in any position other than directly above or directly
below.
WARNING: Never attach swivel mounting xtures to
vertical or angled pipes.
IMPORTANT WARNING
WARNING


Product specificaties

Merk: JL Audio
Categorie: Speaker
Model: M-SWMCPv3-1.315

Heb je hulp nodig?

Als je hulp nodig hebt met JL Audio M-SWMCPv3-1.315 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Speaker JL Audio

Handleiding Speaker

Nieuwste handleidingen voor Speaker