Jindara Barossa Handleiding

Jindara Heater Barossa

Lees hieronder de 📖 handleiding in het Nederlandse voor Jindara Barossa (8 pagina's) in de categorie Heater. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8

1. Subject to clauses 2 & 3 of this warranty, A.F. Gason Pty Ltd ACN 004 667 556 (Gason) warrants the following components of its heaters against defects in workmanship and/or materials for the

following periods from the date of purchase:

(a) the firebox for ten years;

(b) the paint finish for a period of twelve months if the purchaser has followed the instructions provided by Gason in this Operation and Installation Instructions manual; and

(c) all other components for twelve months except the glass, fire brick lining or baffle plate if, in the opinion of Gason, these items have been damaged by impact.

2. This extended warranty does not apply:

(a) if the heater is purchased from a person who has not been authorised by Gason to sell its products;

(b) if, in the opinion of Gason, the heater or any component has been subjected to abuse, misuse, alteration, modification or has not been installed, operated or maintained in accordance with the

instructions provided by Gason; or

3. If you believe that the heater you purchased contains a manufacturing defect and you wish to make a claim under this warranty, please contact an authorised Gason service centre to arrange for an

assessment.

4. If, after assessing the heater, Gason determines that the heater contains a manufacturing fault, Gason may at its discretion:

(a) replace the heater;

(b) repair or replace specific components of the heater; or

5. Parts replaced under this warranty are warranted for the balance of their original warranty period.

6. If, at the discretion of Gason, the heater or any part needs to be replaced, serviced or repaired at an authorised Gason service centre, then the person claiming under this warranty must pay all costs

associated with:

(a) returning the heater; and

(b) the delivery or collection of any new or repaired heater.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably

foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Any benefits you receive under these warranties are in addition to other rights and remedies that you may have as a consumer under a law in relation to the heater to which these warranties relate.

These warranties are given by:

A.F. Gason Pty Ltd

Blake Street

Ararat VIC 3322

Please contact us if you have any queries on:

Phone: 03 5352 2151;

or email us via the “Contact Us” section of our website: www.gason.com.au.

A.F. Gason Pty Ltd reserves the right to modify or alter specifications, materials, etc. in the interest of product improvement.

WARRANTY

Barossa SRS3 Insert

GPN 231079

Barossa SRS3 Insert

Operation & Installation Instructions

REV.A

Please keep these instructions for future reference.

WOODHEATING

Barossa SRS3 Insert

THIS PAGE INTENTIONALLY LEFT BLANK

Barossa SRS3 Insert

WARNING

Read and follow these instructions carefully before installing and using this appliance.

SAVE THESE INSTRUCTIONS

Paint curing and care

WARNING

• A flue fire with resulting damage may occur if this appliance is not installed, operated and

maintained as per this booklet.

• Never place combustible material such as wood, paper or furniture near the appliance.

• This appliance is designed to burn dry wood. Do not burn rubbish, driftwood, flammable

liquids or any substance containing salts or corrosives.

• This appliance must not be installed and operated in an area where kerosene, petrol, paint

thinner or other flammable liquid is used or stored.

• The flue system must be inspected and cleaned annually or sooner if required. Failure to

do so could result in an excessive build up of creosote which may result in a flue fire

which may damage the flue or cause damage to your home.

• The surface of the appliance becomes hot during operation. Do not touch the surface of

this appliance. Keep children away from the appliance during operation. Do not allow

anyone to operate this appliance who is not familiar with the instructions in this booklet.

WARNING

Your heater is coated with the best available heat resistant paint. Even though the paint has

been baked after application, it may require further temperature curing. It may, if you overfire

the heater on its first fire, discolour. For your first two or three firings, never exceed medium

air setting and always have the fan on when above low burn. Do not wipe the heater while the

paint is curing. After the paint has cured the only maintenance required to maintain the

heaters finish is to wipe it with a soft cloth. Do not use any commercial cleaners or solvents

on the paint finish.

We are proud of the presentation of our products. If at any time you need to freshen up the

paint finish, your local dealer has touch up paint available for purchase.

If you have any enquires, please contact the dealer from whom you purchased your heater:

PLEASE COMPLETE:

Dealer Name

Dealer Address

Phone

Please attach your original purchase dockets to this booklet for future reference.

Safety Warnings

Barossa SRS3 Insert

Installation

WARNING

This heater is to be installed into a masonry fireplace or a Jindara ZCV Clearance cabinet.

THE INSTALLATION OF THIS APPLIANCE MUST BE CARRIED OUT AS PER THIS MANUAL AND

THE FLUE MANUFACTURERS SPECIFICATIONS.

WE RECOMMEND THAT YOU USE A QUALIFIED INSTALLER TO CARRY OUT THE

INSTALLATION.

If you have any other enquiries, please contact the dealer from whom you purchased your

heater.

THIS APPLIANCE WEIGHS IN EXCESS OF 120 KILOGRAMS. EXTREME CARE SHOULD BE TAKEN

WHEN HANDLING THE APPLIANCE.

Installation

All dimensions used in this document are in millimetres and are minimum unless otherwise

stated. Under no circumstances can these dimensions be reduced.

A.F. Gason Pty Ltd accepts no liability whatsoever for any interpretation of AS/NZS

2918:2001

Installation Permit

Depending on your local authority requirements, a permit may be required for the

installation of your heater. It is your responsibility to arrange the same.

Installation into existing or masonry fireplace

The Jindara Barossa SRS3 Insert can be installed into a masonry fireplace with a flue

system that is in accordance with the relevant sections of AS/NZS 2198:2001. No

combustible or heat sensitive material may be placed closer than 1340mm from the top of

the hearth/base of appliance and 50mm either side of the appliance’s fascia.

Minimum hearth depth of 510mm from the front of the fascia panel must be achieved. If it

is desired to reduce the hearth depth to the minimum allowable 300mm in front of

appliance fascia, the appliance must be raised to a new height - refer elevated installation

instructions on page 7.

For detailed mantle clearance dimensions, refer to Figure 4.

Brick removal

WARNING

IF BRICKS REQUIRE REMOVAL WHEN PREPARING THE FIREPLACE, ENSURE THAT YOU DO NOT

EXPOSE COMBUSTIBLE MATERIALS BEHIND THE BRICKWORK OR WEAKEN THE INTEGRAL

STRUCTURE OF THE CHIMNEY.

Section showing Installation

Figure 1. Masonry Installation

Barossa SRS3 Insert

• Smoke entering the room from the firebox when the door is open may be caused by

• Insufficient length of flue (Flue to be 4500mm minimum from underneath base of heater to underside of cowl)

– Increase height of flue.

• Flue Downdraught

– Consult dealer or increase height of flue.

• Creosote Build up in flue

– Remove cowl and clean flue as per cleaning instructions. Check moisture content of wood.

• Excessive ash build up

Some woods will give large amounts of ash despite how you run the heater. Others will give you very little. Use the wood which is most

convenient for you as long as it is dry. After a period of time you will get to know when to empty your unit. Bark will give you excessive

ash. Try not to burn it.

If you are burning wood that gives you charcoal, you may find that after running the heater say for 8 hours at maximum burn rate, the

charcoal builds up excessively. Overnight burn will reduce this charcoal back to a fine ash. If you are not ready to shutdown for

overnight burn when you next fuel the stove, load the stove with only one piece of wood and lay it across the firebox on top of the

charcoal. Open the air control wide open and you will find the charcoal will burn down with the one piece of wood. Repeat the process

until the ash level is significantly reduced.

Troubleshooting (Continued)

Product specificaties

Merk:	Jindara
Categorie:	Heater
Model:	Barossa

Heb je hulp nodig?

Als je hulp nodig hebt met Jindara Barossa stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Heater Jindara

Jindara Kimberley Mk2 Handleiding

9 Juli 2023

Jindara Hamersley MK2 Freestanding Handleiding

4 Juli 2023

Jindara Tilga Handleiding

1 Juli 2023

Jindara Hamersley Mk2 Handleiding

28 Juni 2023

Jindara Riverina Handleiding

20 Juni 2023

Jindara Mallee Handleiding

13 Juni 2023

Jindara Spectre Handleiding

12 Juni 2023

Jindara Grange Handleiding

8 Juni 2023

Jindara Gawler Handleiding

31 Mei 2023

Jindara Sturt Handleiding

31 Mei 2023

Handleiding Heater

Nieuwste handleidingen voor Heater

Mestic MKK-250 Handleiding

26 April 2024

Mestic MKK-400 Handleiding

26 April 2024

Delonghi DCH7093ERBCA Handleiding

25 April 2024

Delonghi MDHS12 Handleiding

25 April 2024

Delonghi HFX30C15.WCA Handleiding

25 April 2024

Delonghi MDHU12 Handleiding

25 April 2024

Delonghi HFX12D03 Handleiding

25 April 2024

Delonghi Dragon 4 TRD40615 Handleiding

25 April 2024

Thermotec AeroFlow Midi 1950w Handleiding

18 April 2024

Everdure NPE2400W Handleiding

17 April 2024