JETI MAX BEC Handleiding

JETI Niet gecategoriseerd MAX BEC

Lees hieronder de 📖 handleiding in het Nederlandse voor JETI MAX BEC (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1

Linear regulator MAX BEC

Linear regulator MAX BEC is sophisticated tool regulating a voltage in models which have receiver and servos

servos motion.

Technical data:

Recommended input voltage: 5,5-8,4 V

Max. input voltage: 16 V

Output voltage: 5.0 V, 5.4 V, 5.7 V, 6.0 V

Pulsed current: 12 A

Continuous current: 5 A (see table below)

Idle current: 17 µA

Max. power loss: 7 W

Max. temperature: 130 C

Weight: 25 g

Dimensions: 50 x 25 x 10 mm

Required output voltage (5.0 V, 5.4 V, 5.7 V, 6.0 V) is selected by jumper plug.

MAX BEC can be supplied either by NiXX or LiXX cells, recommended is 2 LiXX cells or 5-6 NiXX cells. Input

voltage is indicated by four LEDs. If the input voltage is above 7.0 V, all three green LEDs are ON. While the cells

are gradually discharging, particular LEDs go OFF depending on input voltage (lower then 7 V, 6.7 V, 6.45 V). If the

input voltage is under 6.5 V, the red LED goes ON indicating that cells are discharged (if using 2S LiXX then it

means that voltage of particular cells is under 3.25 V).

Supply cells must be connected into input side with two 0.5 mm

cables. There is also parallel-connected 3link with

JR connector which is intended for cells charging, without a need for disconnection of power connectors. Maximum

charging current is 0,5 A (limited by connector).

Output voltage is extracted from output side with 2 links. It is recommended to connect both 2-links, it results in

higher reliability and lower current loading on connectors. The connectors may be plugged in any channel of the

receiver.

On the output side, there is switch extracted, which activates the regulator. The switch is connected as “safe”; it

means that mechanical damage of joints or wires has no impact on BEC function.

Datasheet - Continuous current load depending on input/output voltage:

Output voltage [V]

Input voltage

(number of cells) 5 5.4 5.7 6

2 LiXX / 6 NiXX 2.92 [A] 3.50 [A] 4.12 [A] 5.00 [A]

3 LiXX / 10 NiXX 1.15 [A] 1.23 [A] 1.30 [A] 1.37 [A]

12 NiXX 0.85 [A] 0.90 [A] 0.93 [A] 0.97 [A]

JETI model s.r.o., Lomena 1530, 742 58 Pribor, Czech Republic, www.jetimodel.com

Product specificaties

Merk:	JETI
Categorie:	Niet gecategoriseerd
Model:	MAX BEC
Ingebouwd display:	Nee
Gewicht:	28 g
Breedte:	50 mm
Diepte:	25 mm
Hoogte:	10 mm
Spanning:	6 V
Bedrijfstemperatuur (T-T):	-10 - 130 °C
Aantal AC uitgangen:	- AC-uitgang(en)
Nominale input voltage:	16 V