JennAir KDAS104HSS Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor JennAir KDAS104HSS (10 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/10
W11160370B
INSTALLATION INSTRUCTIONS
FOR CUSTOM 18" AND 24" WOOD DOOR PANEL
IMPORTANT: Before installing your dishwashe , please use this instruction sheet as a supplement to the Installation Instructions.r
Custom Panel Models Only
Gather these additional tools and parts before starting attachment
of the custom panel. Read and follow the instructions provided in
this instruction sheet.
Additional Tools Needed:
Power Drill
Phillips-head screwdriver or magnetic bit
Needle nose pliers
Parts Supplied with Custom Panel Models:
â– Template (located inside Use and Care Guide
bag assembly)
NOTE: The screws supplied are used for only a 0.59" (1.5 cm)
thick wooden panel. If the wooden panel is less than 0.59"
(1.5 cm) thick, customer must purchase screws locally.
Custom Panel Dimensions
Max 28.3" (72 cm).
1 . " (4 cm)74 4 4.
M in.0.59" (1.5 cm)
Door
Thickness
18 Custom Panel Dimensions"
Max 28.3" (72 cm).
23. " (5 . cm)4 9 4
Min .0.59" (1.5 cm)
Door
Thickness
24 Custom Panel Dimensions"
S
S
S
SST
T
T
TT3
3
3
33.
.
.
..5
5
5
55X
X
X
XX2
2
2
225
5
5
55
2
2
2
22
3
3
3
33
4
4
4
44
7
7
7
77
8
8
8
8
8
5
5
5
55
1
1
1
110
0
0
00
X
X
X
XX1
1
1
110
0
0
00
9
9
9
99
X
X
X
XX4
4
4
44
X
X
X
XX2
2
2
22
X
X
X
XX2
2
2
22
S
S
S
SST
T
T
TT3
3
3
33.
.
.
..5
5
5
55X
X
X
XX4
4
4
445
5
5
55
1
1
1
111
1
1
11
S
S
S
S
ST
T
T
T
T3
3
3
3
3.
.
.
.
.9
9
9
9
9X
X
X
X
X1
1
1
1
13
3
3
3
3
X
X
X
XX2
2
2
22
S
S
S
S
ST
T
T
T
T3
3
3
3
3.
.
.
.
.5
5
5
5
5X
X
X
X
X9
9
9
9
9
X
X
X
XX
X
X
X
XX2
2
2
22
2
2
2
22
6
6
6
66
S
S
S
SST
T
T
TT4
4
4
44X
X
X
XX1
1
1
114
4
4
44
2
3. Install brackets and studs
Remove the template. Install brackets and studs using the
screws provided.
4. Install customer-supplied handle
IMPORTANT: Make sure to countersink screw heads on back
side of panel so that the screw heads are ush with the panel.
NOTES:
â– The handle for the custom panel is not included.
â– All mounting hardware supplied is for a 0.59" (1.5 cm) thick
wood panel. If a thinner wood panel or materials other than
wood are used, it is the customer’s responsibility to obtain the
proper length screws and adjust the pilot holes accordingly.
IMPORTANT: Use a moisture-resistant sealer on both sides and
all edges of the panel to avoid damage from moisture.
1. Attach template to wood panel
Attach the provided template to the back side of the custom
panel with tape. Make sure that the center of the template is
aligned with the center of the wooden panel and top of the
template is aligned to the top face of the wooden panel.
2. Pre-drill holes for studs and brackets
7. Check the spring tension
Open and close the door to check the spring tension of the door.
8. Adjust spring tension (if needed)
If needed, adjust the spring tension by using a Phillips-head
screwdriver. Turn screws clockwise to increase tension or
counterclockwise to decrease door tension.
5. Slide panel onto door
Align the studs on the custom panel to the keyhole slots on the
door assembly. Ensure that the studs and brackets are engaged
in the keyhole slots. Slide panel down until the top surface of
the panel is ush with the top of the door.
Secure the door panel by inserting the four anchor screws
provided into the inner door frame holes. See screw hole
locations in the above illustration.
©201 8All rights reserved. 01/18
W11160370B
Door spring adjustment
screws
6. Secure the door panel


Product specificaties

Merk: JennAir
Categorie: Niet gecategoriseerd
Model: KDAS104HSS

Heb je hulp nodig?

Als je hulp nodig hebt met JennAir KDAS104HSS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd JennAir

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd