Janome Quilt Maker 18 Handleiding

Janome Naaimachine Quilt Maker 18

Lees hieronder de 📖 handleiding in het Nederlandse voor Janome Quilt Maker 18 (25 pagina's) in de categorie Naaimachine. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/25
QF01510 8-foot Longarm Quilng Frame
(with oponal 2-foot extension)
Assembly Instrucons
January, 2021
Table of Contents
2...........Parts List
3...........Secon 1: Table Top Frame
4...........Secon 2: Leg Assemblies
5...........Secon 3: Legs to Table Top
6...........Secon 4: Corner Braces
7...........Secon 5: Track Supports
8...........Secon 6: Aligning Track
9...........Secon 7: Horizontal Braces, Right & Le
10.........Secon 8: Narrow Vercal Braces
11-12 ...Secon 9: Wide Vercal Braces, Right & Le
13.........Secon 10: Cross Brace
14.........Secon 11: Pole Supports, Ratchet-Stop End
15.........Secon 12: Pole Supports, No Ratchet-Stop End
16.........Secon 13: Ratchet Stops, Shown on Right End
17.........Secon 14: Pole Pre-assembly
18.........Secon 15: Pole Assemblies
19.........Secon 16: Pole Assemblies, 10-Foot
20.........Secon 17: Poles on Frame
21.........Secon 18: Leveling Frame
22.........Secon 19: Velcro and Leaders
23.........Secon 20: Bungee Side Clamps
24.........Secon 21: Loading the Quilt
25.........Secon 22: Changing the Pole Posion Seng
8-foot Longarm Frame Assembly InstruconsPage 2
PART # DESCRIPTION QTY
QF01500-243 LEG CAP, PLASTIC 2
QF09318-178 LEVELER FOOT 2
QF01500-241 LOWER LEG 1
QF01500-242 UPPER LEG 2
QF09318-07 SCREW-M8 X 16 SKB ZN 2
QF05300-157 WASHER-M8 NYLON 2
QF01500-170 CROSS BAR, 1
QF01500-200 BRACE, CORNER 4
QF01500-211 RAIL, 24” 2
QM13274 WASHER-M4 FLAT ZN 16
QM13237 SCREW-M4 X 12 BUTTON HEAD 24
QF01500-270 SCREW-M4 X 10 FLAT HEAD 4
QF01500-230 TRACK SUPPORT 24” 2
QF01500-300-30 POLE COUPLER 4
QF01500-300-10 POLE SECTION, SHORT (2’) 4
QF09318-714 SNAP BUTTON 4
QF01500-251 TRACK INSERT, 10’ 2
PART # DESCRIPTION QTY
QF01510-100 VERTICAL BRACE, NARROW 2
QF01510-110 VERTICAL BRACE, WIDE (RIGHT) 1
QF01510-120 VERTICAL BRACE, WIDE (LEFT) 1
QF01510-130 BRACE, CROSS 2
QF01510-150 HORIZONTAL BRACE ( ) 1RIGHT
QF01510-160 HORIZONTAL BRACE (LEFT) 1
QF01500-170* CROSS BAR 6
QF01500-180 RATCHET STOP 3
QF01500-190 POLE SUPPORT, PLASTIC 8
QF01500-200 BRACE, CORNER 8
QF01500-210* RAIL, 48” 4
QF01500-220* TRACK SUPPORT, 36” 4
QF01500-230* TRACK SUPPORT, 24” 2
QF01500-243 LEG CAP, PLASTIC 6
QF09318-178 LEVELER FOOT 6
QF01500-241 LOWER LEG 3
QF01500-242 UPPER LEG 6
QF09318-07 SCREW-M8 X 16 SKB ZN 6
QF05300-157 WASHER-M8 NYLON 6
QF01500-260 SCREW-M6 X 14 SHOULDER ZN 3
QF01500-270 SCREW-M4 X 10 FLAT HEAD 44
QF01500-300-20* POLE SECTION, LONG (4’) 8
QF09318-714 SNAP BUTTON 8
QF01500-800 RATCHET WHEEL 3
QF01500-300-30 POLE COUPLER 4
QM13237 SCREW-M4 X 12 BUTTON HEAD 116
QM13274 WASHER-M4 FLAT ZN 81
QF00035 BUNGEE SIDE CLAMP 2
QF00035-1 CORD LOCK 2
QF01500-250 TRACK INSERT, 8 FT 2
QF09318-113 5MM HEX KEY HANDLE 1
QF09318-111 3MM HEX KEY HANDLE 1
QF09318-116 2.5MM HEX DRIVER TOOL 1
QF01503 7.5’ LEADER SET 1
QF10619 VELCRO 3/4 HOOK WHITE ADHSV 1
Parts Lists
Parts List 8-foot Longarm Quilng Frame Parts List 2-foot Extension (oponal)
BOX 1: Includes everything without an asterisk
*BOX 2: Includes items with an asterisk
Page 3
8-foot Longarm Frame Assembly Instrucons
Tools Needed: 2.5mm hex tool ( ) and provided
measuring tape ( )not provided .
1. Lay the parts out as shown. Assemble the table
frame using two screws down through the rail
at each end into the threaded inserts in the
cross bars.
NOTE: Start all the screws at both ends
of the three cross bars before ghtening
them with the provided 2.5mm hex tool.
2. Repeat this process for the other two cross
bars.
3. Tighten the screws rmly with the 2.5mm
hex tool.
4. Repeat Steps 1 through 3 for a second table
top frame.
Â10" NOTE: If you are using the oponal
2-foot extension repeat Steps 1 through
3 for the one cross bar on the short table
top frame.
5. Flip the table top frames upside down and
align them together.
ÂIMPORTANT: Using a measuring tape
measure diagonally from one outside
corner to the other outside corner. The
measurement should be very close
to 53". Repeat the process diagonally
across the other two corners. The two
measurements should be the same to
ensure the top is squared. Secons will
be joined with table legs.
3
2
1
Secon 1: Table Top Frame
ITEM PART # DESCRIPTION QTY
1 QF-01500-270 SCREW-M4 X 10 FLAT HEAD 24
2 QF01500-210 48” RAIL, 4
3 QF01500-170 CROSS BAR 6
NOTE: If you are using the oponal
2-foot extension, place it in the
center between the two 4-secons
8-foot table frame shown together
without oponal 2-foot extension
10-foot table frame shown together with
oponal 2-foot extension in the center


Product specificaties

Merk: Janome
Categorie: Naaimachine
Model: Quilt Maker 18

Heb je hulp nodig?

Als je hulp nodig hebt met Janome Quilt Maker 18 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Naaimachine Janome

Handleiding Naaimachine

Nieuwste handleidingen voor Naaimachine