Integral LED ILSTRGBWB030E Handleiding
Pagina's 4 Lamp
Bekijk de handleiding van Integral LED ILSTRGBWB030E gratis online of download de PDF. 53 mensen vonden deze handleiding nuttig. Vraag over dit model? Stel een vraag
Flexible 24V INTEGRAL LED RGBW Strip IP65
Installation Guide
Pour des instructions en français, merci de
vous rendre à l’adresse www.integral-led.
com an de les télécharger directement
depuis la page du produit (‘Product’ sur
le site) dans la section Téléchargement
(‘Download’)
IMPORTANT NOTICE
• This product should be installed according to the instructions in this guide and by a qualied electrical installer.
• All electrical work must be completed in accordance with the latest IET wiring regulations (formally IEE) for the UK or in accordance with all applicable
regulations and laws in the country in which it is being installed. This product falls under a low voltage Class circuit category.III
• Switch OFF power at the mains before installing the LED strip.
• S trip must only be installed indoors or in outdoor areas are sheltered. Unit is protected against water jets and dust. Not suitable for water immersion.
• Avoid looking directly at the strip when turned on, for a long period of time.
• Observe the operating temperature of the LED strip: -25C to +60C.
To avoid any damage to the LED strip or driver
• Always disconnect or switch o the power supply before cutting or connecting an LED strip. Wait at least one minute before connecting to a recently
powered driver.
• Always handle the LED strip with care.
• Observe the correct polarity for 24V connections (g 1).
• Safely route and secure all wires so they cannot be pinched or damaged.
• Do NOT power the strip whilst in its packaging reel.
• Do NOT twist the LED strip or heavily press down on the area above LEDs.
INTRODUCTION
• This installation guide is for exible, IP65 constant voltage self-adhesive LED strips produced by Integral LED.
• Depending on your installation, you can purchase additional accessories such as mounting clips.
A) CHOOSING A 24V LED DRIVER
• This LED strip operates with a 24V DC constant-voltage power supply known as a driver. Drivers are sold separately and are available in varying wattage outputs.
• The specication of the driver required will depend on the total power requirement of the connected strip(s). The power output of the driver (wattage
rating) must be at least 20% higher than the total required wattage of the strip(s) being powered.
For example, if you are installing 5 LED strips of 1M each and the power requirement of each 1M strip is 3W/metre – the total power requirement is 15W.
The power rating of the driver should be a least 20% above 15W i.e. A minimum of 18W
• Ensure the LED driver specication and IP rating is correct for your application.
B) PRE-INSTALLATION GUIDE
LED strips make a great addition to any domestic or commercial environment. They can change the mood and look of a space instantly and are very energy
ecient. The possibilities are endless so the requirement for each lighting project will be dierent.
It is worth taking some time to plan your project for the desired eect before removing the backing tape on the LED strip. The specication, length, mounting position
and distance from an object determines the appearance of a lit LED strip. You will also need to consider the placement and concealment, of the 24V LED driver, control
unit and wires and the power switch to turn the LED strip ON and OFF.
We recommend that you test the strip by temporarily holding the LED strip in place by using a suitable tape, such as masking tape. Safely connect the power
supply - you can then carefully move the strip to try dierent angles and positions to gain the desired illumination eect and position. Check for light spots,
reections and shadows.
Please consider the surface you are applying the LED strip to; the surface should be stable, clean and smooth. On removal of a xed LED strip - damage to
paint, wallpaper or other substrates may occur. Take care in measuring the length required before cutting the strip, take into account the space required for the
connection wires. You may also consider using a spirit level, plumb line or other guide if required.
In the bag
1 X 5M ±5cm IP65 INTEGRAL LED RGBW STRIP on reel pre-tted with an
appropriate connector to connect to a suitable control unit and power
supply.
IP65
WARNING
DO NOT CONNECT THE LED STRIP DIRECTLY TO A MAINS SUPPLY.
THE LED STRIP MUST ONLY BE CONNECTED TO A SUITABLE 24V LED DRIVER.
Product specificaties
| Merk: | Integral LED |
| Categorie: | Lamp |
| Model: | ILSTRGBWB030E |
| Kleur van het product: | Beige |
| Gewicht: | 280 g |
| Breedte: | 12 mm |
| Energie-efficiëntieklasse: | G |
| Gewicht verpakking: | 285 g |
| Breedte verpakking: | 180 mm |
| Diepte verpakking: | 11 mm |
| Soort: | Universeel strooklicht |
| Materiaal behuizing: | Polycarbonaat (PC) |
| Aantal lampen: | 360 gloeilamp(en) |
| Type lamp: | LED |
| Vermogen lamp: | 12 W |
| Internationale veiligheidscode (IP): | IP65 |
| Ondersteuning voor plaatsing: | Binnen |
| Montagewijze: | Plakband |
| Type stroombron: | DC |
| Certificering: | CE RoHS |
| Duurzaamheidscertificaten: | Laagspanningsrichtlijn (LVD) |
| Plug and play: | Ja |
| Aantal per verpakking: | 1 stuk(s) |
| Lengte: | 5000 mm |
| Levensduur lamp: | 15400 uur |
| Kleur licht: | Blue, Green, Red, White |
| Op afstand bedienbaar: | Ja |
| Totaal vermogen: | 60 W |
| Beschermingsklasse: | III |
| Dimbaar: | Ja |
| Color Rendering Index (CRI): | 80 |
| Stralingshoek: | 115 ° |
| Geschikt voor soort licht: | Ambiance |
| Operating voltage: | 24 V |
| Van kleur veranderend: | Ja |
| Soepelheid: | Ja |
| Geïntegreerde LED: | Ja |
| Bedrijfstemperatuur (T-T): | -25 - 60 °C |
| Energie-efficiëntieschaal: | A tot G |
| Kleurtemperatuur (min): | 4000 K |
| Garantieperiode: | 3 jaar |
| Energieverbruik per 1000 uur: | 12 kWu |
Heb je hulp nodig?
Als je hulp nodig hebt met Integral LED ILSTRGBWB030E stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Lamp Integral LED
Integral LED ILSTRGBA033E Handleiding Integral LED ILSTWHIA054E Handleiding Integral LED ILSTRGBWB028E Handleiding Integral LED ILSTWHIA101E Handleiding Integral LED ILSTWHIA100E Handleiding Integral LED ILSTRGBWB043E Handleiding Integral LED ILSTRGBWA027E Handleiding Integral LED ILSTRGBWA029E Handleiding
Alle Integral LED Lamp handleidingen
Populair in Lamp
Handleiding Lamp
Nieuwste handleidingen voor Lamp
Chauvet COLORdash Par-H18XM Handleiding Dals Napa NAPF12-CC-UNV Handleiding Cateye GVolt300Lm HL-EL083GRC Handleiding V-Tac VT-10179 Handleiding Yato YT-08588 Handleiding Cateye NANO F II TL-LD831-F Handleiding V-Tac VT-10180 Handleiding V-Tac VT-9-157 Handleiding V-Tac VT-81004 Handleiding Brennenstuhl SL 2500 AT Handleiding