Inovonics EN1266 Handleiding

Bekijk gratis de handleiding van Inovonics EN1266 (3 pagina’s), behorend tot de categorie Bewegingsdetector. Deze gids werd als nuttig beoordeeld door 13 mensen en kreeg gemiddeld 4.6 sterren uit 2 reviews. Heb je een vraag over Inovonics EN1266 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

3.28.22 357-00047-04 Rev A © Inovonics, 2022 - www.inovonics.com

EN1266 360° Ceiling Mount Motion Detector

Installation and Operation Manual

1 Overview

The EN1266 360° ceiling mount motion detector is a four-element passive

infrared intrusion detector for use in electronic security systems in ceiling

mount applications. The EN1266 reduces false alarms to a minimal level

due to its elimination of background noises and nuisance stimuli, employs

automatic pulse count to make it adaptable to various environments, and

uses sophisticated signal processing to make it virtually free of false

alarms. The lens provides wide coverage patterns, even at low mounting

heights, and is especially immune to sunlight, as well as halogen and

fluorescent lights.

1.1 Inovonics Contact Information

If you have any problems with this procedure, contact Inovonics technical

support:

•E-mail: support@inovonics.com.

•Phone: (800) 782-2709; (303) 939-9336.

2 Installation and Startup

2.1 Installation Notes

•These products are designed to be installed and maintained by

professional security technicians.

•Products are tested for indoor use.

•All products should be manually tested weekly.

2.2 Install the Batteries

The EN1266 uses two batteries for extra battery life.

Note: When installing batteries, it is recommended that batteries are

replaced in new pairs from the same manufacturer.

To install batteries:

1. Remove the housing cover from the base.

Figure 1 Remove the housing cover.

2. Install the batteries included with the unit.

Figure 2 Install the batteries

2.3 Select Pulse Count

The pulse count options provides control for difficult operating

environments. Automatic pulse count is recommended for reliable

operation in environments subject to temperature fluctuation that can

cause false alarms. The single pulse count mode is more sensitive to minor

temperature variations, and should be used in sites where variant heat

sources will not cause alarms. Automatic pulse count is the factory default

because it allows more reliable operation in environments subject to

temperature fluctuation. To select pulse count:

1. Press the tamper button five times within three seconds.

Figure 3 Press the tamper button

2. Wait for the green LED to blink five times, then:

•Press the tamper button one time within three seconds to select single

pulse count.

•Press the tamper button two times within three seconds to select

automatic pulse count.

3. Confirm your selection.

•The green LED will blink once to indicate single pulse count has been

selected; twice to confirm automatic pulse count has been selected.

2.4 Select Fixed/Variable Sleep Time

The sleep time setting provides control for normal or high-traffic operating

environments. When set to fixed, if the EN1266 senses motion, it will

transmit an alarm, then enter sleep mode for 180 seconds; if motion is

sensed when the sleep time has expired, the EN1266 will transmit another

alarm. Fixed sleep time is recommended for normal operating

environments, and is the default setting as shipped from the factory. When

set to variable, if the EN1266 senses motion, it will transmit an alarm, then

enter sleep mode for 180 seconds; if motion is sensed before the sleep

time has expired, the EN1266 will restart the 180 second interval. Variable

sleep time is recommended for high-traffic operating environments. To

select sleep time:

1. Press the tamper button four times within three seconds.

2. Wait for the green LED to blink four times, then:

•Press the tamper button one time within three seconds to select fixed

sleep time.

For product and installation videos visit us at

www.inovonics.com/videos or use the QR

code below.

Product specificaties