Indesit PN 641 /I (OW) Handleiding

Indesit Fornuis PN 641 /I (OW)

Lees hieronder de 📖 handleiding in het Nederlandse voor Indesit PN 641 /I (OW) (6 pagina's) in de categorie Fornuis. Deze handleiding was nuttig voor 18 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6

IMPORTANT SAFETY INSTRUCTIONS

These instructions shall also be available on website: docs.indesit.eu

YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY IMPORTANT

This manual and the appliance itself provide important safety messages, to be read and observed at all times.

This is the safety alert symbol, pertaining to safety, which alerts users to potential hazards to themselves and others.

All safety messages will follow the safety alert symbol and either the terms:

Indicates a hazardous situation which, if not avoided, will cause serious injury.

Indicates a hazardous situation which, if not avoided, could cause serious injury.

All Safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

- The appliance must be disconnected from the power supply before carrying out any installation work.

- Installation and maintenance must be carried out by a qualied technician, in compliance with the manufacturer’s instructions and local safety regulations. Do not repair

or replace any part of the appliance unless specically stated in the user manual.

If the information in this manual is not followed exactly, a re or explosion may result causing property damage or injury.

- Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this appliance.

What to do if you smell gas:

- Do not try to light any appliance.

- Do not touch any electrical switch.

- Do not use any phone in your building.

- Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

- If you cannot reach your gas supplier, call the re department.

- Installation and service must be performed by a qualied installer, service agency or the gas supplier.

- Use appliance in well ventilated rooms only.

The electrical and gas connections must comply with local regulations.

• When the hob is installed, provide a multi-pole circuit breaker with a contact separation of at least 3 mm, that

provides full disconnection.

• Regulations require that the appliance is grounded.

• The power cable must be long enough for connecting the appliance, once tted in its housing, to the power supply.

• Use only exible or rigid metal hose for gas connection.

• If necessary, the electrical power cable must be replaced exclusively with a power cable having identical

characteristics to the original supplied by manufacturer. This operation must be performed by a qualied electrician.

• The manufacturer cannot be held responsible for any injury to persons or animals or damage to property arising

from failure to comply with these requirements.

• Do not use multiple plug adapters or extension cords.

• Do not pull the power cable to disconnect it from the electrical supply.

• The electrical components must not be accessible to the user after installation.

• Do not touch the appliance with any wet part of the body and do not operate it when barefoot.

• This hob (class 3) is designed solely for private household use for cooking food. Do not use this appliance as

a space heater to heat or warm the room. Doing so may result in carbon monoxide poisoning and overheating

of the hob. The Manufacturer declines all responsibility for inappropriate use or incorrect setting of the controls.

• The appliance and its accessible parts become hot during use. Care should be taken to avoid touching heating

elements. Children less than 8 years of age shall be kept away unless continuously supervised. This appliance

can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning

use of the appliance in a safe way and understand the hazards involved. They shall not play with the appliance.

Cleaning and user maintenance shall not be made by children without supervision.

• The use of a gas appliance produces heat and humidity in the room. Make sure the room is well-ventilated, or

install an extractor hood with exhaust duct.

DANGER

RNINGWA

400011188026

BUILT-IN GAS HOB

• Domestic animals should be kept away from the appliance.

• In case of prolonged use, additional ventilation may be necessary (by opening a window or increasing the hood

extraction speed).

• After use, make sure the knobs are in off position and close the main gas supply cock or the gas cylinder valve.

• Overheated oils and fats catch re easily. Always remain vigilant when cooking foods rich in fat, oil or alcohol

(e.g. rum, cognac, wine).

• Keep the packaging materials out of the reach of children.

• Before cleaning or maintenance wait for hob to cool down.

• Unattended cooking on a hob with fat or oil can be dangerous and may result in re. NEVER try to extinguish a

re with water, but switch off the appliance and then cover ame e.g. with a lid or a re blanket.

• Danger of re: do not store items on the cooking surfaces.

SAVE THESE INSTRUCTIONS

INSTALLATION

After unpacking the hob, make sure that it has not been damaged during transport. In the event of problems, contact the dealer or your nearest After-sales Service.

These instructions are only valid for the countries whose symbols is given on the data plate (under the hob).

TECHNICAL INFORMATION FOR THE INSTALLER

• This product can be embedded in a worktop 20 to 50 mm thick.

• If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening in the work surface. This panel, that has to

close completely the cutout in order to avoid any contact with the bottom part of the hob, must be positioned at a maximum distance of 150 mm below

the upper surface of the work surface but, in no case less than 20 mm from the bottom of the hob. In the case that you intend to install an oven beneath

the hob, make sure that it is manufactured by Whirlpool and equipped with a cooling system. The manufacturer declines all liability if another brand

oven is installed beneath the hob.

• Before installation, make sure that:

the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the rating plate and injector table);

- the outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations;

- this appliance is not connected to a fume exhaust device. It shall be installed in accordance with current installation regulations. Particular attention shall be given

to the relevant requirements regarding ventilation.

- combustion products are discharged outdoors through specic hoods or wall and/or window mounted electrical fans.

GAS CONNECTION

This operation must be performed by a qualied technician.

• The gas supply system must comply with local regulations.

• You can nd specic local regulations for some countries in the paragraph “Reference to Local Regulations”.If no information

concerning your Country is given, please ask details to your Installer.

• The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper or steel pipe

with ttings complying with local regulations, or by means of a continuous-surface stainless steel hose complying with local

regulations. Interpose gasket (B) in the elbow connection.The maximum length of the hose is 2 m.

• FOR BELGIUM ONLY: It is necessary to replace the elbow connection (A) on the appliance, with the one supplied (if present).

IMPORTANT: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of the furniture.

It must pass through an area where there are no obstructions and where it is possible to inspect it on all its length.

• After connection to the gas supply, check for leaks with soapy water. Light up the burners and turn the knobs from max position to minimum position to check

ame stability.

ELECTRICAL CONNECTION.

This operation must be performed by a qualied technician.

• The electrical connections must comply with local regulations.

• The earthing of this appliance is compulsory by law.

• Do not use an extension cord.

IMPORTANT: the data relevant to the voltage and power absorption are indicated on the rating plate.

RNINGWA

Earth

(yellow/green)

EAVERTIZAR

ASSEMBLY

After having cleaned the perimeter surface, apply the supplied gasket to the hob as shown in the gure.

Position the hob in the worktop opening made respecting the dimensions indicated in the Instruction.

NOTE: the power supply cable must be long enough to permit its upward extraction.

To secure the hob, use the brackets (A) provided with it. Fit the brackets into the relevant bores shown by the arrow and fasten them by means of their screws in accordance

with the thickness of the worktop (see the following gures).

Top 20 mm

Top 30-50 mm

ADJUSTMENT TO DIFFERENT TYPES OF GAS

This operation must be performed by a qualied technician.

If the appliance is intended to operate with a different gas from the gas type stated on the rating plate and information label on the top of the hob, change the injectors.

Remove the information label and keep it with the instructions booklet.

Use pressure regulators suitable for the gas pressure indicated in the Instruction.

• The gas nozzles must be changed by After Sales Service or a qualied technician.

• Nozzles not supplied with the appliance must be ordered from After Sales Service.

• Adjust the minimum setting of the taps.

NOTE: when liquid petroleum gas is used (G30/G31), the minimum gas setting screw must be tightened as far as it will go.

IMPORTANT: should you experience difculty in turning the burners knobs, please contact the After Sales Service for the replacement of the burner tap

if found to be faulty.

REPLACING THE INJECTORS (see the injector table in the Instruction)

• ).Remove grids (A

• Extract burners (B).

• Using a socket spanner of the appropriate size unscrew the injector ( ), unscrew the injector to be replaced.C

• Replace it with the injector suitable for the new type of gas.

• ).Re-assemble the injector in (D

• ). If you have a multiple crown burner use side spanner to replace the injector (E

Before installing the hob, remember to afx the gas calibration plate supplied with the injectors in such a way that it covers

the existing information relating to gas calibration.

ADJUSTING MINIMUM GAS SETTING OF TAPS

To ensure that the minimum setting is correctly adjusted, remove the knob and proceed as follows:

• tighten screw to reduce the ame height (-);

• loosen screw to increase the ame height (+)

The adjustment must be performed with the tap in minimum gas setting position (small ame) .

• The primary air of the burners does not need to be adjusted.

• At this stage, light up the burners and turn the knobs from max position to check ame stability. to minimum position

Upon completion of adjustment, reseal using sealing wax or an equivalent material.

REFERENCE TO LOCAL REGULATIONS

Provision for ventilation

The room in which the appliance is installed must have an air supply to current B.S. 5440 - Part 2 standards.

All rooms require a permanent vent in addition to the openable window.

If there are other fuel burning appliances in the same room B.S. 5440 - Part 2 should be consulted to determine the air vent requirements.

If the appliance is installed in a cellar or basement, it is advisable to provide an air vent of 65 cm, irrespective of the room volume.

Gas Safety Regulations

The law requires that all gas appliances are installed by competent persons in accordance with the current gas safety regulations. Failure to install appliances correctly

may lead to prosecution.

It is in your own interest, and that of safety, to ensure that the law is complied with. The hob should be installed in accordance with the Gas Safety (Installation and

Use) Regulations Building Regulations, the issued by the Department of the Environment and the Building Standard (Scotland) (Consolidation) Regulations,