IFM SF3003 Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor IFM SF3003 (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 147 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6
Montageanleitung
Installation Instructions
Notice de Montage
Strömungssensor SF
Flow sensor SF
Sonde de débit SF
R
701150/04 05/2009
Bestimmungsgemäße Verwendung
Der Strömungssensor überwacht in Verbindung mit dem Schaltverstär-
ker VS0200 Strömungen in flüssigen und gasförmigen Medien. Die
Sensor-Verstärker-Kombination erfaßt, ob ein voreingestellter Strö-
mungswert erreicht ist (= Medium strömt) oder nicht (= Medium
strömt nicht) und meldet dies durch ein Schaltsignal.
Montage
Die Sensorspitze sollte vollständig ins Medium hineinragen.
Montieren Sie das Gerät bei waagerecht verlaufenden Rohren mög-
lichst seitlich (Abb 1). Bei Montage von unten sollte die Rohrleitung frei
von Ablagerungen sein. Bei Montage von oben sollte die Rohrleitung
vollständig mit dem zu überwachenden Medium gefüllt sein.
Montieren Sie das Gerät bei senkrecht verlaufenden Rohren in der
Steigleitung (Medium strömt aufwärts, Abb. 2).
A = 15mm fĂĽr M12 x 1 und G 1/4; A = 33mm fĂĽr G 1/2.
Um Fehlfunktionen zu vermei-
den, müssen Mindestabstände
zwischen Sensor und KrĂĽmmun-
gen, Ventilen u. ä. eingehalten
werden: Mindestens 5 mal Rohr-
durchmesser an der Anströmseite
(A), mindestens 3 mal Rohrdurch-
messer an der Abströmseite (B).
Elektrischer Anschluss
Anschluss an Schaltverstärker VS0200; Spannungsversorgung nach
EN50178, SELV, PELV. Das Gerät darf nur von einer Elektrofachkraft
installiert werden. Befolgen Sie die nationalen und internationalen Vor-
schriften zur Errichtung elektrotechnischer Anlagen.
2
A
1
A
2
D
A
B
min.
5 x D
min.
3 x D
3
Dichtung Dichtung
Functions and features
In conjunction with the VS 0200 control monitor the flow sensor monitors
flows in liquids and gases. The sensor / control monitor combination
senses whether there is a preset flow rate (= medium flowing) or not
(= medium not flowing) and provides a switched signal.
Installation
The sensor tip must be completely immersed in the medium.
In the case of horizontal pipes mount the unit from the side, if possi-
ble (fig. 1). When the unit is to be mounted at the bottom of the pipe,
it should be free from deposits. When the unit is to be mounted at the
top of the pipe, it should be completely filled with the medium to be
monitored.
In the case of vertical pipes mount the unit in a place where the medi-
um flows upwards (fig. 2).
A = 15mm for M12 x 1 and 1/4"; A = 33mm for 1/2".
To avoid malfunction a minimum
distance between the flow moni-
tor and bends, valves or such like
must be observed. Min. 5 x pipe
diameter upstream (A), min. 3 x
pipe diameter downstream (B).
Electrical connection
Connection to control monitor VS 0200; voltage supply to EN50178,
SELV, PELV. The unit must only be mounted by an electrician.
The national and international regulations for the installation of
electrical equipment must be observed.
3
A
1
A
2
3
packing washer packing washer


Product specificaties

Merk: IFM
Categorie: Niet gecategoriseerd
Model: SF3003

Heb je hulp nodig?

Als je hulp nodig hebt met IFM SF3003 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd IFM

IFM

IFM DP4302 Handleiding

12 April 2024
IFM

IFM EVCB02 Handleiding

11 Maart 2024
IFM

IFM EVCB03 Handleiding

11 Maart 2024
IFM

IFM EVF666 Handleiding

11 Maart 2024
IFM

IFM TM4599 Handleiding

8 Januari 2024
IFM

IFM ZB0074 Handleiding

8 Januari 2024
IFM

IFM EVF661 Handleiding

8 Januari 2024
IFM

IFM IIP201 Handleiding

7 Januari 2024
IFM

IFM DP4200 Handleiding

7 Januari 2024
IFM

IFM IIP200 Handleiding

7 Januari 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd