Ice-O-Matic Elevation CIM1447HA Handleiding
Ice-O-Matic
Ijsmachine
Elevation CIM1447HA
Lees hieronder de đź“– handleiding in het Nederlandse voor Ice-O-Matic Elevation CIM1447HA (17 pagina's) in de categorie Ijsmachine. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.9 sterren beoordeeld
Pagina 1/17
Ice-O-Matic
11100 East 45th Avenue
Denver, Colorado 80239
1-800-423-3367
9081484-01 REV. M
02/2020
ELEVATION SERIES CUBE ICE MAKER
CIM 300 lb through 2000 lb Cubers
Installation Guide and Owner’s Manual
ELEVATION SERIES INTRODUCTION
1
Energy Efficiency
Ice-O-Matic has partnered with ENERGY STAR since 2004 to ensure our customers receive the most
efficient ice machines for your investment dollar. Ice-O-Matic is committed to the continuous
improvement in both energy efficiency and productivity thereby delivering the best value in energy
efficient ice machines money can buy.
For a detailed list of ENERGY STAR qualified Ice-O-Matic ice machines, go to:
http://www.iceomatic.com/Products/Sales-Literature/
Freight Claims
Inspect Promptly
This merchandise has been carefully inspected
and packed in accordance with the carrier’s
packing specifications. Responsibility for safe
delivery has been assumed by the carrier. If
loss or damage occurs, you as the consignee
must file a claim with the carrier and hold the
container for carrier’s inspection.
Visible Loss or Damage
Any external evidence of loss or damage must
be fully described and noted on your freight
bill or express receipt and signed by the
carrier’s agent. The claim should be filed on a
form available from the carrier.
Concealed Loss or Damage
If loss or damage does not appear until
merchandise has been unpacked, make a
written request for inspection by the carrier
within 5 days of the delivery date, then file a
claim on a form from the carrier.
FILE CLAIMS WITHOUT DELAY
DO NOT RETURN DAMAGED GOODS
TO ICE-O-MATIC
How to use this Manual
Ice-O-Matic provides this manual as an aid to the service technician in installation and maintenance of the
CIM Series cube ice machines. Do not attempt to perform installation, start-up or maintenance unless you
have read and fully understand this manual.
Ice-O-Matic ice-makers and dispensers are not approved for outdoor installation.
Air and water cooled ice machines are hermetically sealed and contain fluorinated greenhouse gas
R404A (GWP 3922) or R449A (GWP 1282).
Models containing R449A are designated with the suffix, -49. (Ex. CIM1135HA4-49)
For a Service Provider, please reference our “Find a Service Technician” tab at www.iceomatic.com
Keep this manual for future reference
The CIM Series Service Parts Manuals are available separately.
WARNING
Always disconnect electrical power and shut off water supply whenever maintenance or repairs are
performed on the ice machine and related equipment
CAUTION
Always wear protective eyewear whenever maintenance or repairs are performed on the ice machine
and related equipment
Ice-O-Matic Warranty
Every Ice-O-Matic ice maker is backed by a warranty that provides both parts and labor coverage. To view
the warranty details, register products, or check your warranty status visit the “Warranty and Water Filter
Registration” page on www.iceomatic.com
ELEVATION SERIES INSTALLATION GUIDELINES
2
For proper operation of the ice machine, the
following installation guidelines must be followed
by a qualified refrigeration technician. Failure to
do so may result in loss of production capacity,
premature part failures, and may void all
warranties.
Reference the installation parameters prior to
installing the machine. Ice-O-Matic assumes no
responsibility for improperly installed equipment.
Excessive time required for service or time for
units requiring removal for service of inaccessible
equipment will be the sole responsibility of the
equipment owner.
This appliance is not to be used by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction. Children shall be
supervised and are not to play with the appliance.
Ambient Operating Temperature
Minimum operating temperature:
50°F (10°C)
Maximum operating temperature:
100°F (38°C) (60 Hz.), 110°F (43°C) (50 Hz.).
Note: Ice-O-Matic ice-makers and dispensers are not
approved for outdoor installation
Incoming Water Supply
WARNING: Connect to unheated potable water
supply only
(see Electrical and Plumbing diagrams for line sizing)
Minimum incoming water temperature:
40°F (4.5°C)
Maximum incoming water temperature:
100°F (38°C)
Minimum incoming water pressure:
20 psi (1.4 bar, 0.138MPa)
Maximum incoming water pressure:
80 psi (5.5 bar, 0.552MPa)
Note: if water pressure exceeds 80 psi (5.5 bar), a water
pressure regulator must be installed
All water supply lines must be installed per local
codes. Use 3/8 inch O.D. minimum on air cooled
machines. On water cooled machines 3/8 inch O.D.
minimum tubing must be run to the condenser. The
water supply for the machine can “T” off from the
condenser line using 3/8 inch O.D. minimum
tubing. Make 2 coils of extra tubing so that the
machine can be pulled away from the wall if
service is needed.
Water Filtration/Treatment
A water filter system should be installed with the
ice machine. Refer to Ice-O-Matic water filter
specification sheet.
Reverse Osmosis (RO) water can be very acidic and
can attack the evaporator and other metal in the ice
machine. Because the RO process removes all
minerals and metals from the water it can promote the
faster growth of microbial mold and slime. If RO
water is used, Ice-O-Matic recommends the water pH
is verified to be a neutral 7.0 to minimize the
corrosive effects. Incorrect cleaners, sanitizers, and
RO water that does not have a neutral pH could void
the machine’s warranty.
Drains
All drain lines must be installed per local codes.
Flexible tubing is not recommended. Route bin
drain, purge drain and water condenser drain
individually to a floor drain. The use of condensate
pumps for draining water is not recommended.
Ice-O-Matic assumes no responsibility for
improperly installed equipment.
Note: The purge drain fitting is plastic: DO
NOT apply heat to purge drain area; DO NOT
over-tighten drain connection
All drain lines must be installed per local codes.
The purge drain should be a minimum of 3/4 inch
O.D. tubing. The condenser drain on water cooled
units should be 1/2 inch O.D. minimum. The drain
line fittings on Ice-O-Matic bins are 3/4 FPT. The
bin drain should be a minimum of 3/4 inch O.D.
Cold water drains should be insulated to prevent
condensation from forming.
Installation Guidelines
Product specificaties
| Merk: | Ice-O-Matic |
| Categorie: | Ijsmachine |
| Model: | Elevation CIM1447HA |
Heb je hulp nodig?
Als je hulp nodig hebt met Ice-O-Matic Elevation CIM1447HA stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Ijsmachine Ice-O-Matic
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
Handleiding Ijsmachine
- Ijsmachine Petra Electric
- Ijsmachine Haier
- Ijsmachine Sage
- Ijsmachine Magimix
- Ijsmachine Edgestar
- Ijsmachine Kogan
- Ijsmachine Perlick
- Ijsmachine WestBend
- Ijsmachine Aconatic
- Ijsmachine Maxxfrost
- Ijsmachine Proline
- Ijsmachine Bosch
- Ijsmachine NewAir
- Ijsmachine FriFri
- Ijsmachine Studio
Nieuwste handleidingen voor Ijsmachine
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025