Hughes & Kettner Switchblade 100 TSC Combo Handleiding
Hughes & Kettner
Niet gecategoriseerd
Switchblade 100 TSC Combo
Lees hieronder de ๐ handleiding in het Nederlandse voor Hughes & Kettner Switchblade 100 TSC Combo (64 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 5 personen en werd door 3 gebruikers gemiddeld met 3.9 sterren beoordeeld
Pagina 1/64
english
deutsch
franรงais
espaรฑol
italiano
Switchblade TSC
Head 100, Combo 100, Combo 50
Manual 1.1
2
S w i t c h b l a d e T S C
Foreword
The installed Tube Safety Control (TSC) safeguards your tubes, amp, and sound.
Beyond that, for the first time it puts into your hands a tool that helps you
manage and check your old and new EL34 and even 6L6GC tubes at any time.
Players have long wished for a tube amp that is as low-maintenance as a solid-state
amps, and TSC has made that wish come true.
Best wishes from the Hughes & Kettnerยฎ team. We hope you enjoy playing your
SWITCHBLADE TSC as much as we enjoyed designing and refining it!
Things to Do Before Operating the Amp
Please read the safety instruction on page 64!
A word of warning before you fire up your SWITCHBLADE TSC: Itโs loud!
High volume levels can cause hearing damage. Ensure plenty of air can circulate
around your ampโs ventilation surfaces. Place the amp on a sturdy, secure base
and avoid exposing it to mechanical shocks and extreme temperatures that could
endanger the device or your and othersโ safety. The manufacturer disclaims any
liability or responsibility whatsoever for any damage or defect to this and other
devices resulting from misuse.
Powering Up
Ensure SWITCHBLADE TSCโs MAINS and STANDBY switches are off (with
the toggle switch pointing down) and that the voltage rating indicated next to the
MAINS INPUT (alongside the Voltage Setting arrow as depicted the illustration)
matches your local Mains current before you plug the amp in.
The illustration shows the 100/120 volt version as
an example. The voltage rating 100V is indicated
next to the arrow, meaning that the amp may be
powered with 100V Mains voltage only. If the
rating indicated next to the arrow does not match
the local Mains voltage, do not plug your SWITCHBLADE TSCโs Mains cord
into an outlet! More on this in chapter 9.
Head Only
First plug the speaker cord into the
appropriate output on the Head. Do
not use more than one of these outputs
simultaneously! That is, use either 1x4 ฮฉ,
2x16 ฮฉ, 1x8 ฮฉ, or 1x16 ฮฉ. Donโt mix and match cabinets either, say by plugging
a 4-ฮฉ cabinet into the 4-ฮฉ output and a 16-ฮฉ cabinet into the 16-ฮฉ output. For
more on this, see chapter 6.5.
Plug the other end of the cord into the speaker cabinetโs Input. This is vital
to every all-tube ampโs life! Power amps may be damaged when tube amps are
operated without a connected speaker load or at an insufficient impedance level!
Combo Only
Check to ensure the wire to the internal speaker is connected properly to the
power amp (see figure). Note that on the 50W Combo, the internal speaker is
connected to the 8-ฮฉ output. On the 100W Combo, it is connected to the 16-ฮฉ
output.
Head and Combo
To avoid very unpleasant surprises, make a habit of always twisting the MASTER
knob to the far left-hand position before turning on the amp.
Input
Connect your guitar to this Input. Please use suitable shielded cords only โ no
speaker cords allowed.
Mains
This switch opens the flow of main current supply, and the blue PILOT LAMP
lights up. Ensure the STANDBY switch is set to OFF and allow the tubes plenty
of time to warm up. Theyโll thank you for your patience with a longer service life.
Standby
The STANDBY switch breathes life into those glowing tubes. It controls the
anode voltage, not the heating. When taking a short break from playing, please
use STANDBY rather ON/OFF so the tubes remain at operating temperature.
If you canโt wait to get to it, go ahead and play your SWITCHBLADE TSC
now. The patient reader is well advised to continue reading before letting it rip.
Particularly chapters 1 (Handling) and 7 (Programming) are mandatory, even for
seasoned players.
Standard Setup and Cable Connections
๎๎๎๎๎๎
๎๎๎๎๎๎๎๎๎๎๎
๎๎๎๎๎๎๎๎๎๎
๎๎๎๎๎๎๎๎๎๎
๎๎๎๎๎๎๎๎๎๎๎
๎ฟ๎ฟ๎๎๎๎๎๎๎
๎๎๎๎๎๎
๎๎๎๎๎๎๎๎๎๎๎
๎๎๎๎๎๎๎๎๎๎
๎๎๎๎๎๎๎๎๎๎
๎๎๎๎๎๎๎๎๎๎๎
๎ฟ๎ฟ๎๎๎๎๎๎๎
Product specificaties
| Merk: | Hughes & Kettner |
| Categorie: | Niet gecategoriseerd |
| Model: | Switchblade 100 TSC Combo |
Heb je hulp nodig?
Als je hulp nodig hebt met Hughes & Kettner Switchblade 100 TSC Combo stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Hughes & Kettner
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
Handleiding Niet gecategoriseerd
- Niet gecategoriseerd Zylight
- Niet gecategoriseerd Nutrichef
- Niet gecategoriseerd Cool Head
- Niet gecategoriseerd Venicci
- Niet gecategoriseerd Cablexpert
- Niet gecategoriseerd Beverage-Air
- Niet gecategoriseerd Racktime
- Niet gecategoriseerd Soundcraft
- Niet gecategoriseerd Newline
- Niet gecategoriseerd Lervia
- Niet gecategoriseerd Phidgets
- Niet gecategoriseerd Soler & Palau
- Niet gecategoriseerd Worx
- Niet gecategoriseerd HQ
- Niet gecategoriseerd Steren
Nieuwste handleidingen voor Niet gecategoriseerd
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025
9 Juni 2025