Hughes & Kettner Red Box Mk II Handleiding
Hughes & Kettner
Niet gecategoriseerd
Red Box Mk II
Bekijk gratis de handleiding van Hughes & Kettner Red Box Mk II (1 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 4 mensen en kreeg gemiddeld 4.4 sterren uit 2.5 reviews. Heb je een vraag over Hughes & Kettner Red Box Mk II of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/1
HUGHES
&
KETTNER
RED
BOX
The RED BOX enables you to connect your
consolewithout the problems of miking. The
uitar amplifier directly to a sta
abinetulator
circuitry
of the RE
e or studio mixing
BOX authentically
recreates the sound of a
miked-up
guitar cabinet loaded with four 12” loudspeakers.
Advantages:
-
No phase cqnceiiation through interaction with other open microphones.
-
None of the extraneous noises a microphone would pick up
(stage rumble. bleed-through from other instruments).
-
No need to lug and position an extra mike and mike stand on stage,
uncluttered stage appearance.
-
Reduced set-up time, consistent sound.
Instructions:
VERY IMPORTANT: Turn off power to the amp before making
any
connections to
the RED BOX. Failure to do so can result in non-warranty damage to the RED BOX.
Also VERY IMPORTANT: If
you connect a tube amp to the SPEAKER IN jack, you
must also connect a speaker (or at least a dummy load) to the RED BOX
SPEAKER THRU jack. Failure to do so may damage the amp. (Just like revving an
engine in neutral without a load at maximum RPM’s can damage an engine).
First, install a 9-volt battery Power from this battery is automatically turned on
by the insertion of a standard
1/4"
plug into either the LINE IN or SPEAKER IN,
and is turned back off simply by removing the plug.
Connections:
A tube output stage plays a major role in the creation of an amplifier’s tone.
With tube amps it is therefore recommended that the RED BOX be connected
to the amplifier’s loudspeaker output (and the RED BOX SPEAKER THRU be
connected to the speaker). With transistor amplifiers, however, for the sake of
the best dynamics and signal-to-noise ratio, the preamp signal (LINE OUT) is
preferred.
Transistor amp
IN
Tube amp
Technical specifications:
Operational voltage : 9 volts DC
Power consumption : 1 mA
LINE IN
:
maximum 2.3 volts, impedance 20 Kohms
LINE OUT: balanced, impedance 200 ohms
Gain
:
OdB
Adapter (optional)
: Ring =
+,
Tip =
-.9
to 20 volts DC
HUGHES
&
KETTNER
VERTRUEB
HUGHES
&
KETTNER INC.
W.-GERMANY
35 SUMMIT AVENUE
C T
PA
Product specificaties
| Merk: | Hughes & Kettner |
| Categorie: | Niet gecategoriseerd |
| Model: | Red Box Mk II |
Heb je hulp nodig?
Als je hulp nodig hebt met Hughes & Kettner Red Box Mk II stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Niet gecategoriseerd Hughes & Kettner
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
Handleiding Niet gecategoriseerd
- Squarp Instruments
- True & Tidy
- Laserluchs
- Bintec-elmeg
- Innoliving
- Auto XS
- Mamiya
- Ankilo
- Healthy Choice
- Perixx
- TFA Dostmann
- Dayclocks
- Oklahoma Sound
- Breville
- Realme
Nieuwste handleidingen voor Niet gecategoriseerd
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025
16 Juni 2025