Hotpoint WMF 740 A Handleiding

Hotpoint Wasmachine WMF 740 A

Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint WMF 740 A (16 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 17 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/16



English, 1

Contents

Installation, 2-3-4-5

Unpacking and levelling

Connecting the electricity and water supplies

The first wash cycle

Technical data

Description of the washing machine

and starting a wash cycle, 6-7

Control panel

Indicator lights

Starting a wash cycle

Wash cycles, 8

Table of wash cycles

Personalisation, 9

Setting the temperature

Setting the spin speed

Functions

Detergents and laundry, 10

Detergent dispenser drawer

Preparing the laundry

Garments requiring special care

Load balancing system

Precautions and tips, 11

General safety

Disposal

Opening the porthole door manually

Care and maintenance, 12

Cutting off the water or electricity supply

Cleaning the washing machine

Cleaning the detergent dispenser drawer

Caring for the door and drum of your appliance

Cleaning the pump

Checking the water inlet hose

Troubleshooting, 13

Assistance, 14

WMF 740 P/G/A/K

Instructions for use

WASHING MACHINE

Installation

Levelling your appliance correctly will provide it with

stability and avoid any vibrations, noise and shifting

during operation. If it is placed on a fitted or loose

carpet, adjust the feet in such a way as to allow

enough room for ventilation beneath the washing

machine.

Electric and water connections

Connecting the water inlet hose

1. Insert seal A into the

end of the inlet hose and

screw the latter onto a

cold water tap with a 3/4

gas threaded mouth

(see figure).

Before making the

connection, allow the

water to run freely until

it is perfectly clear.

2. Connect the other end

of the water inlet hose to

the washing machine,

screwing it onto the

appliance's cold water

inlet, situated on the top

right-hand side on the

rear of the appliance (see

figure).

3. Make sure there are no kinks or bends in the

hose.

!The water pressure at the tap must be within the

values indicated in the Technical details table

(on the next page).

!If the water inlet hose is not long enough, contact

a specialist store or an authorised serviceman.

!Ensure that the supply taps are allowing water

through. Old taps may seize in the closed position

and thus prevent water reaching the machine.

!Keep this instruction manual in a safe place for

future reference. Should the appliance be sold,

transferred or moved, make sure the instruction

manual accompanies the washing machine to inform

the new owner as to its operation and features.

!Read these instructions carefully: they contain

vital information on installation, use and safety.

Unpacking and levelling

U n p a c k i n g

1. Unpack the washing machine.

2. Check whether the washing machine has been

damaged during transport. If this is the case, do

not install it and contact your retailer.

3. Remove the 2

protective screws and

the rubber bush with

the respective spacer,

situated on the rear of

the appliance (see also

the installation leaflet).

NB:The plastic spacers

may fall down inside the

machine once the bolt

has been removed, and will not interfere with the

operation of the machine.

4. Do not remove external bar.

5. Seal the gaps using the plastic plugs provided.

6. Keep all the parts: you will need them again if

the washing machine needs to be moved to

another location.

!Packaging materials are not children's toys.

L e v e l l i n g

Your machine may make a considerable amount of

noise if the two front feet have not been adjusted

correctly.

1. Install the washing machine on a flat sturdy

floor, without resting it up against walls, furniture

cabinets or other.

2. If the floor is not

perfectly level, com-

pensate for any

unevenness by

tightening or loosening

the adjustable front

feet (see figure); the

angle of inclination,

measured according to

the worktop, must not

exceed 2°.

_the supply voltage is included within the values

indicated on the Technical details table

(see page 5);

_the socket is compatible with the washing

machine's plug. If this is not the case, replace

the socket or the plug.

Your appliance is now supplied with a 13 amp fused

plug it can be plugged into a 13 amp socket for

immediate use. Before using the appliance please

read the instructions below.

WARNING - THIS APPLIANCE MUST BE EARTHED.

THE FOLLOWING OPERATIONS SHOULD BE CARRIED

OUT BY A QUALIFIED ELECTRICIAN.

Replacing the fuse:

When replacing a faulty fuse, a 13 amp ASTA

approved fuse to BS 1362 should always be used,

and the fuse cover re-fitted. If the fuse cover is

lost, the plug must not be used until a replacement

is obtained.

Replacement fuse covers:

If a replacement fuse cover is fitted, it must be of

the correct colour as indicated by the coloured

marking or the colour that is embossed in words on

the base of the plug. Replacements can be obtained

directly from your nearest Service Depot.

Removing the plug:

If your appliance has a non-rewireable moulded plug

and you should wish to re-route the mains cable

through partitions, units etc., please ensure that

either:

the plug is replaced by a fused 13 ampere re-

wearable plug bearing the BSI mark of approval.

or:

the mains cable is wired directly into a 13 amp cable

outlet, controlled by a switch, (in compliance with

BS 5733) which is accessible without moving the

appliance.

Disposing of the plug:

Ensure that before disposing of the plug itself, you

make the pins unusable so that it cannot be

accidentally inserted into a socket.

Instructions for connecting cable to an alternative

plug:

Important: the wires in the mains lead are coloured

in accordance with the following code:

Green & Yellow E a r t h

B l u e N e u t r a l

B r o w n L i v e

65 - 100 cm

Where it connects to

the waste water pipe

cut end off spigot or

remove the blanking cap

Connecting the drain hose

Connect the drain

hose, without bending

it, to a draining duct or

a wall drain situated

between 65 and 100 cm

from the floor;

The drain hose may be

connected to an under-

sink trap. Before

connecting the drain

hose from the machine

ensure that any blanks

or removable ends have

been taken off the

spigot.

If it is place over the

edge of a basin or sink

be sure the free end

of the hose should not

be underwater.

! We advise against the use of hose extensions; in

case of absolute need, the extension must have

the same diameter as the original hose and must

not exceed 150 cm in length.

Ensure that if the drain hose is pushed into a

standpipe, that the end does not go down more

than 15cms (6 inches). If the hose is pushed down

too far, this may cause the machine to self -

syphon ie. continuously empty as it is filling.

Electric connection

Before plugging the appliance into the mains

socket, make sure that:

_the socket is earthed and in compliance with

the applicable law;

_the socket is able to sustain the appliance's

maximum power load indicated in the Technical

details table (see page 5);

Product specificaties

Merk:	Hotpoint
Categorie:	Wasmachine
Model:	WMF 740 A
Apparaatplaatsing:	Vrijstaand
Kleur van het product:	Zilver
Deurscharnieren:	Rechts
Breedte:	595 mm
Diepte:	565 mm
Hoogte:	850 mm
Type lader:	Voorbelading
Uitgestelde start timer:	Ja
Energieverbruik wassen:	- kWu
Waterconsumptie per cyclus:	- l
Wasklasse:	A
Centrifuge-droger klasse:	B
Maximale centrifugesnelheid:	1400 RPM
Aantal wasprogramma's:	4
Nominale capaciteit:	7 kg
Wasprogramma's:	Hygiene/anti-allergy, Black