Hotpoint H3B L626 B UK Handleiding

Hotpoint Vaatwasser H3B L626 B UK

Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint H3B L626 B UK (8 pagina's) in de categorie Vaatwasser. Deze handleiding was nuttig voor 34 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8

1 2 43 5 6 7

1. On-O/Reset button with indicator light

2. Program selection button with indicator light

3. Half Load button with indicator light

4. Rinse Aid rell indicator light

5. Salt rell indicator light

6. Program indicator lights

7. Delay indicator light

8. Delay button with indicator light

9. Tablet (Tab) button with indicator light

10. Start/Pause button with indicator light / Drain out

DAILY REFERENCE

GUIDE

CONTROL PANEL

Before using the appliance carefully read Safety Instructions guide.

APPLIANCE

THANK YOU FOR BUYING A HOTPOINT PRODUCT.

In order to receive a more complete assistance, please

You can download the Safety Instructions and the User

Manual, by visiting our website docs.hotpoint.eu

and following the Instructions on the back of this

booklet.

1. Upper rack

2. Foldable aps

3. Upper rack height adjuster

4. Upper spray arm

5. Lower rack

6. Cutlery basket

7. Lower spray arm

8. Filter Assembly

9. Salt reservoir

10. Detergent and Rinse Aid dispensers

11. Rating plate

12. Control panel

0000 000 00000

Service:

PRODUCT DESCRIPTION

FIRST TIME USE

SALT, RINSE AID AND DETERGENT

ADVICE REGARDING THE FIRST TIME USE

After installation, remove the stoppers from the racks and the retaining

elastic elements from the upper rack.

FILLING THE SALT RESERVOIR

The use of salt prevents the formation of LIMESCALE on the dishes

and on the machine’s functional components.

• It is mandatory that THE SALT RESERVOIR NEVER BE EMPTY.

• It is important to set the water hardness.

The salt reservoir is located in the lower part of the dishwasher

(see PRODUCT DESCRIPTION) and must be lled when the SALT REFILL

indicator light in the control panel is lit .

1. Remove the lower rack and unscrew the

reservoir cap (anticlockwise).

2. Only the rst time you do this: ll the salt

reservoir with water.

3. Position the funnel (see gure) and ll the salt

reservoir right up to its edge (approximately

1 kg); it is not unusual for a little water to leak

out.

4. Remove the funnel and wipe any salt residue

away from the opening.

Make sure the cap is screwed on tightly, so that no detergent can get

into the container during the wash program (this could damage the wa-

ter softener beyond repair).

Whenever you need to add salt, it is mandatory to complete the pro-

cedure before the beginning of the washing cycle to avoid corrosion.

SETTING THE WATER HARDNESS

To allow the water softener to work in a perfect way, it is essential that

the water hardness setting is based on the actual water hardness in your

house. This information can be obtained from your local water supplier.

The factory sets the default value for the water hardness.

• Switch on the appliance by pressing the button.ON/OFF

• Switch o the appliance by pressing the button.ON/OFF

• Hold down button START/Pause for 5 seconds, until you hear a beep.

• Switch on the appliance by pressing the button.ON/OFF

• The program indicator light of the current set level ashes.

• Press button to select the desired hardness level (Psee WATER

HARDNESS TABLE).

Water Hardness Table

Level °dH

German degrees

°fH

French degrees

°Clark

English degrees

1 Soft 0 - 6 0 - 10 0 - 7

2 Medium 7 - 11 11 - 20 8 - 14

3 Average 12 - 16 21 - 29 15 - 20

4 Hard 17 - 34 30 - 60 21 - 42

5Very

hard 35 - 50 61 - 90 43 - 62

• Switch o the appliance by pressing the button.ON/OFF

Setting is complete!

As soon as this procedure is complete, run a program without loading.

Only use salt that has been specically designed for dishwashers.

After the salt has been poured into the machine, the SALT REFILL indi-

cator light switches o.

If the salt container is not lled, the water softener and the heating

element may be damaged as a result of limescale accumulation.

Using of Salt is recommended with any type of dishwasher detergent.

FILLING THE RINSE AID DISPENSER

Rinse aid makes dish DRYING easier. The rinse aid dispenser should be A

lled when the indicator light in the control RINSE AID REFILL

panel is lit.

1. Open the dispenser by pressing and pulling up the tab on the lid.B

2. Pour in the rinse aid (max.110 ml), making sure it does not overow

from the dispenser. If this happens, clean the spill immediately with

a dry cloth.

3. Press the lid down until you hear a click to close it.

NEVER pour the rinse aid directly into the appliance tub.

ADJUSTING THE DOSAGE OF RINSE AID

If you are not completely satised with the drying results, you can ad-

just the quantity of rinse aid used.

• Switch the dishwasher on using the button.ON/OFF

• Switch it o using the button.ON/OFF

• Press button START/Pause three times - a beep will be heard.

• Switch it on using the button.ON/OFF

• The program indicator light of the current set level ashes.

• Press button to select the level of rinse aid quantity to be supplied.P

• Switch it o using the buttonON/OFF

Setting is complete!

If the rinse aid level is set to 1 (ECO), no rinse aid will be supplied. The

LOW RINSE AID indicator light will not be lit if you run out of rinse aid.

A maximum of 5 levels can be set according to the dishwasher model.

The factory setting is specic to the model, please follow instruction

above to check this for your machine.

• If you see bluish streaks on the dishes, set a low number (2-3).

• If there are drops of water or limescale marks on the dishes, set

a mid-range number (4-5).

FILLING THE DETERGENT DISPENSER

To open the detergent dispenser use the opening device C.

Introduce the detergent into the dry dispenser D only. Place

the amount of detergent for pre-washing directly inside the tub.

1. When measuring out the detergent

refer to the mentioned earlier infor-

mation to add the proper quantity.

Inside the dispenser there are indiD-

cations to help the detergent dosing.

2. Remove detergent residues from

the edges of the dispenser and clo-

se the cover until it clicks.

3. Close the lid of the detergent

dispenser by pulling it up until

the closing device is secured in pla-

ce.

The detergent dispenser automatically opens up at the right time

according to the program.

If all-in-one detergents are used, we recommend using the TABLET

button, because it adjusts the program so that the best washing

and drying results are always achieved.

Usage of detergent not designed for dishwashers may cause mal-

function or damage to the appliance.

Program

Drying phase

Available

options *)

Duration

of wash

program

(h:min)**)

Water

consumption

(litres/cycle)

Energy

consumption

(kWh/cycle)

1. Eco 50° 3:35 9.5 0.95

2. Intensive 65° 2:40 18.0 1.60

3. Mixed 55° 2:15 16.0 1.40

4. Rapid 28’ 50° - 0:28 9.0 0.50

5. Soak - - 0:12 4.7 0.01

PROGRAMS TABLE

PROGRAMS DESCRIPTION

Instructions on wash cycle selection.

1 ECO

Eco programme is suitable to clean normally soiled tableware, that

for this use, it is the most ecient programme in terms of its combined

energy and water consumption, and that it is used to assess complian-

ce with the EU Ecodesign legislation.

2 INTENSIVE

Program recommended for heavily soiled crockery, especially suitable

for pans and saucepans (not to be used for delicate items).

3 MIXED

Mixed soil. For normally soiled dishes with dried food residues.

4 28’RAPID

Program to be used for half load of lightly-soiled dishes with no dried

food residues. Does not include drying phase.

5 SOAK

Use to refresh crockery planned to be washed later. No detergent to be

used with this program.

Notes:

Please note that cycle is dedicated for lightly soiled dishes.Rapid 28’

ECO program data is measured under laboratory conditions according to European Standard EN 60436:2020.

Note for Test Laboratories:

For information on comparative EN testing conditions, please send an email to the following address:

dw_test_support@whirlpool.com

Pre-treatment of the dishes is not needed before any of the programs.

*) Not all options can be used simultaneously.

**) Values given for programs other than the program Eco are indicative only. The actual time may vary depending on many factors such as temperature

and pressure of the incoming water, room temperature, amount of detergent, quantity and type of load, load balancing, additional selected options

and sensor calibration. The sensor calibration can increase program duration up to 20 min.

Product specificaties

Merk:	Hotpoint
Categorie:	Vaatwasser
Model:	H3B L626 B UK
Apparaatplaatsing:	Volledig ingebouwd
Soort bediening:	Knoppen
Gewicht:	35500 g
Breedte:	598 mm
Diepte:	555 mm
Hoogte:	820 mm
Netbelasting:	1900 W
Aantal couverts:	14 couverts
Automatische programma's:	Ja
Droogsysteem:	Statisch
Snoerlengte:	1.3 m
Uitgestelde start timer:	Ja
Startvertraging:	8 uur
Resterende tijd indicatie:	Nee
Kinderslot:	Nee
Duur cyclus:	215 min
Geluidsniveau:	46 dB
Energie-efficiëntieklasse:	E
Gewicht verpakking:	37500 g
Breedte verpakking:	625 mm
Diepte verpakking:	675 mm
Hoogte verpakking:	910 mm
Verlichting binnenin:	Nee
Waterconsumptie per cyclus:	9.5 l
Stroom:	13 A
Geluidsemissieklasse:	C
Tijdsduur tot uitschakelen:	12 min
Aantal wasprogramma's:	5
Energieverbruik per 100 cycli:	95 kWu
Verstelbare voeten:	Ja
Land van herkomst:	Polen
Douane productcode (TARIC):	84221100
Productafmeting:	Volledige grootte (60 cm)
Bestek compartiment type:	Mand
Kuip materiaal:	Roestvrijstaal
Vloerindicatielampje:	Nee
Zout indicator:	Ja
Glansmiddel indicator:	Ja
Bescherming tegen overstromen:	Ja
Aantal temperatuurinstellingen:	3
Extra droog:	Nee
Half-geladen:	Ja
Afwasprogramma's:	Eco 50°C, Intensive 65°C, Mixed, Soak
Bovenste mand verstelbare hoogte:	Ja
Automatische deuropening:	Nee
Maximale warmwatertoevoertemperatuur:	60 °C
Temperatuur (max):	70 °C
Aantal mandjes:	2 mand(en)
Stroomverbruik (ingeschakeld houden):	0.5 W
Stroomverbruik (indien uit):	0 W
Export Control Classification Number (ECCN):	84221100
AC-ingangsspanning:	220-240 V
AC-ingangsfrequentie:	50 Hz
Producthoogte:	Standaard (80-85 cm)
Hotpoint-technologieën (afwas):	Half Load