Hotpoint H2 D81W E UK Handleiding

Bekijk gratis de handleiding van Hotpoint H2 D81W E UK (4 pagina’s), behorend tot de categorie Wasdroger. Deze gids werd als nuttig beoordeeld door 44 mensen en kreeg gemiddeld 4.6 sterren uit 9 reviews. Heb je een vraag over Hotpoint H2 D81W E UK of wil je andere gebruikers van dit product iets vragen? Stel een vraag

CONTROL PANEL

DAILY USE

Doing this will keep your machine working at its BEST:

- remember to empty your water tank after each drying cycle.

- remember to clean your condenser unit regularly (monthly).

- remember to clean your lter after each drying cycle.

Refer to the Care & Maintenance section.

1. Plug the dryer into the power supply socket.

2. Open the door and load garments; always refer to instructions on

clothing labels and the max loads indicated in the drying time table.

Empty pockets. Make sure garments do not get caught between the

door and/or the door lter.

3. Close the door.

4. Turn the “Drying Time" selection knob until the indicator is

pointing towards the most suitable drying time for the type of

fabric in that load.

Note: do not attempt to turn the knob anticlockwise.

5. If necessary, set the temperature using the "High Heat" button.

6. Press the "Start" button to begin drying.

7. A nal COOL TUMBLE phase (i.e. the fabrics are cooled) activates

during the last few minutes of the drying cycle; always allow this

phase to nish.

8. The cycle ends when the selection knob reaches the "0" zero

position and the drum stops.

9. Open the door, remove the laundry.

10. Disconnect the dryer from the power supply.

11. Clean the lter and replace it.

12. Empty the water tank and put it back in its slot.

OPENING THE DOOR DURING THE CYCLE

Laundry can be checked while the drying cycle runs and any

garments already dry can be removed, while drying continues for

the remaining items. After closing the door, press the "Start" button

to resume machine operation.

DESCRIPTION OF CONTROL PANEL

1. "Start" button

Press to begin drying.

2. "Drying Time" selection knob

This is used to set the drying time: turn the knob in a clockwise

direction until the indicator is set to the desired drying time. The

0 position switches o the dryer.

3. "Emptying Water Tank" indicator light

To indicate when the water tank needs emptying.

Lighting up when the container is full, the door is closed and the

"Start" button has been pressed.

After emptying, reposition it correctly and the light will take

around 30 seconds to switch o after restarting the drying cycle

with the "Start" button.

IMPORTANT: If the container becomes full during the cycle, the

dryer will automatically stop and clothes will not be dried. To

avoid this empty the tank after or before starting a cycle.

4. "High Heat" button

To be used to increase the heat on drying cycles.

CARE LABEL

Always check the care labels, especially when placing garments

in the tumble dryer for the  rst time. Below are the most

commonly used symbols:

May be tumble dried.

Do not tumble dry.

Tumble dry – high heat.

Tumble dry – low heat.

FIRST TIME USE

Remove all the tapes used to hold items on the machine.

Before you use it, clean the inside of the drum to remove any

dust that could have accumulated during transport. Slight odour

or vapour may be found if you open the door during its rst use,

this is normal and should only last a few minutes.

Make sure that the water tank is correctly inserted. Make sure

that the drain hose on the back of the dryer is properly

connected, either to the dryer’s water tank or to your domestic

drainage system.

The dryer must be installed in a room with a temperature

ranging between 5°C and 35°C to ensure proper operation.

THANK YOU FOR BUYING A HOTPOINT PRODUCT.

In order to receive a more complete assistance, please

register your product on www.hotpoint.eu/register

EN

Quick guide

Before using the appliance carefully read the Safety

Instructions.

42 1

3

Product specificaties