Hotpoint BHWMXL 145 UK Handleiding

Hotpoint Wasmachine BHWMXL 145 UK

Lees hieronder de đź“– handleiding in het Nederlandse voor Hotpoint BHWMXL 145 UK (20 pagina's) in de categorie Wasmachine. Deze handleiding was nuttig voor 20 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/20
GB
1
English, 1
Contents
Installation, 2-3-4-5-6-7
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Instructions for the fitter
Care and maintenance, 8
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 9
General safety
Disposal
Description of the washing machine
and starting a wash cycle, 10-11
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 12
Table of wash cycles
Personalisation, 13
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 14
Detergent dispenser drawer
Preparing the laundry
Garments requiring special care
Load balancing systemy
Troubleshooting, 15-16
Product Guarantee and Repair Informa-
tion, 17
GB
BHWMXL 145
Instructions for use
WASHING MACHINE
2
GB
the angle of inclination, measured according to
the worktop, must not exceed 2°.
Levelling your appliance correctly will provide
it with stability and avoid any vibrations, noise
and shifting during operation. If it is placed on
a fitted or loose carpet, adjust the feet in such
a way as to allow enough room for ventilation
beneath the washing machine.
Electric and water connections
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to
a cold water tap using
a 3/4 gas threaded
connection (see figu-
re).
Before performing the
connection, allow the
water to run freely un-
til it is perfectly clear.
2. Connect the other
end of the water inlet
hose to the washing
machine, screwing it
onto the appliance’s
cold water inlet, situa-
ted on the top right-
hand side on the rear
of the appliance (see
figure).
3. Make sure there are no kinks or bends in the
hose.
! The water pressure at the tap must be within
the values indicated in the Technical details
table (on the page 5).
! If the water inlet hose is not long enough,
contact a specialist store or an authorised
serviceman.
! Ensure that the supply taps are allowing wa-
ter through. Old taps may seize in the closed
position and thus prevent water reaching the
machine.
Installation
! Keep this instruction manual in a safe place for
future reference. Should the appliance be sold, tran-
sferred or moved, make sure the instruction manual
accompanies the washing machine to inform the
new owner as to its operation and features.
! Read these instructions carefully: they contain
vital information on installation, use and safety.
Unpacking and levelling
Unpacking
! This is a separate
part of the polystyre-
ne base and should
be removed with the
base.
! IMPORTANT check
when unpacking
your machine.
1. Unpack the washing machine.
2. Check whether the washing machine has
been damaged during transport. If this is the
case, do not install it and contact your retailer.
3. Remove the 4 pro-
tective screws and
the rubber bush with
the respective spacer,
situated on the rear of
the appliance (see also
the installation leaflet).
4. Seal the gaps using the plastic plugs provided.
5. Keep all the parts: you will need them again
if the washing machine needs to be moved to
another location.
! Packaging materials are not children’s toys.
Levelling
Your machine may make a considerable amount
of noise if the two front feet have not been adjusted
correctly.
1. Install the washing
machine on a flat sturdy
floor, without resting it
up against walls, furni-
ture cabinets or other.
2. If the floor is not per-
fectly level, compensa-
te for any unevenness
by tightening or loo-
sening the adjustable
front feet ; (see figure)
GB
3
Connecting the drain hose
Connect the drain
hose, without ben-
ding it, to a draining
duct or a wall drain
situated between 65
and 100 cm from the
floor;
The drain hose may
be connected to an
under-sink trap. Before
connecting the drain
hose from the machine
ensure that any blanks
or removable ends
have been taken off
the spigot.
If it is placed over
the edge of a basin
or sink be sure the
free end of the hose
should not be under-
water.
! We advise against the use of hose extensions;
in case of absolute need, the extension must
have the same diameter as the original hose and
must not exceed 150 cm in length.
Ensure that if the drain hose is pushed into a
standpipe, that the end does not go down more
than 15cms (6 inches). If the hose is pushed
down too far, this may cause the machine to self
-syphon ie. continuously empty as it is filling.
Electric connection
Before plugging the appliance into the mains
socket, make sure that:
• the socket is earthed and in compliance with
the applicable law;
• the socket is able to sustain the appliance’s
maximum power load indicated in the Tech-
nical details table (see page 5);
• the supply voltage is included within the
values indicated on the Technical Data Plate
fixed on the machine.
• the socket is compatible with the washing
machine’s plug. If this is not the case, repla-
ce the socket or the plug.
Your appliance is now supplied with a 13 amp
fused plug it can be plugged into a 13 amp
socket for immediate use. Before using the ap-
pliance please read the instructions below.
WARNING - THIS APPLIANCE MUST BE
EARTHED.
THE FOLLOWING OPERATIONS SHOULD BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Replacing the fuse:
When replacing a faulty fuse, a 13 amp ASTA
approved fuse to BS 1362 should always be
used, and the fuse cover re-fitted. If the fuse
cover is lost, the plug must not be used until a
replacement is obtained.
Replacement fuse covers:
If a replacement fuse cover is fitted, it must be
of the correct colour as indicated by the colou-
red marking or the colour that is embossed in
words on the base of the plug. Replacements
can be obtained directly from your nearest
Service Depot.
Removing the plug:
If your appliance has a non-rewireable moul-
ded plug and you should wish to re-route the
mains cable through partitions, units etc.,
please ensure that either:
the plug is replaced by a fused 13 ampere rewi-
reable plug bearing the BSI mark of approval.
or:
the mains cable is wired directly into a 13
amp cable outlet, controlled by a switch, (in
compliance with BS 5733) which is accessible
without moving the appliance.
Disposing of the plug:
Ensure that before disposing of the plug itself,
you make the pins unusable so that it cannot
be accidentally inserted into a socket.
Instructions for connecting cable to an alternati-
ve plug:
Important: the wires in the mains lead are co-
loured in accordance with the following code:
Green & Yellow Earth
Blue Neutral
Brown Live
65 - 100 cm
Where it connects to
the waste water pipe
cut end off spigot or
remove the blanking cap


Product specificaties

Merk: Hotpoint
Categorie: Wasmachine
Model: BHWMXL 145 UK

Heb je hulp nodig?

Als je hulp nodig hebt met Hotpoint BHWMXL 145 UK stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Wasmachine Hotpoint

Handleiding Wasmachine

Nieuwste handleidingen voor Wasmachine