Hotpoint-Ariston LL 40 EU.C/HA Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint-Ariston LL 40 EU.C/HA (60 pagina's) in de categorie Vaatwassers. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/60
DISHWASHER
Contents
Installation, 2-3
Positioning and levelling
Connecting the water and electricity supplies
Technical data
Description of the appliance, 4
Overall view
Control panel
Loading the racks, 5
Lower rack
Cutlery basket
Upper rack
Start-up and use, 6
Starting the dishwasher
Loading the detergent
Washing options
Wash cycles, 7
Wash cycle table
Rinse aid and refined salt, 8
Loading the rinse aid
Loading the refined salt
Care and maintenance, 9
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the filters
Leaving the machine unused for extended periods
Precautions and advice, 10
General safety
Disposal
Saving energy and respecting the environment
Troubleshooting, 11
Assistance, 12
Before calling for Assistance
English, 1
EN
Instruction booklet
LL 40
Espanol, 13
ES
Polski, 25
PL
Hrvatski, 37
HR RU
Ðóññêèè, 49
2
EN Keep this instruction manual in a safe place for
future reference. If the appliance is sold, given away or
moved, please ensure the manual is kept with the
machine, so that the new owner may benefit from the
advice contained within it.
Please read this instruction manual carefully: it
contains important information regarding the safe
installation, use and maintenance of the appliance.
If the appliance must be moved at any time, keep it
in an upright position; if absolutely necessary, it may be
tilted onto its back.
Positioning and levelling
1. Remove the appliance from all packaging and check
that it has not been damaged during transportation.
If it has been damaged, contact the retailer and do not
proceed any further with the installation process.
2. Check the dishwasher by placing it so that its sides or
back panel are in contact with the adjacent cabinets or
even with the wall. This appliance can also be recessed
under a single worktop (
see the Assembly instruction
sheet*
).
3. Position the dishwasher on a level and sturdy floor. If
the floor is uneven, the front feet of the appliance may be
adjusted until it reaches a horizontal position (the angle of
inclination must not exceed 2 degrees). If the appliance is
levelled correctly, it will be more stable and much less
likely to move or cause vibrations and noise while it is
operating.
Connecting the water and electricity
supplies
Connection to the water and electricity supplies
should only be performed by a qualified technician.
The dishwasher should not stand on top of the water
hoses or the electricity supply cable.
The appliance must be connected to the water
supply network using new piping.
- Do not use old piping.
The water inlet (A) and outlet (B) hoses and the
electricity supply cable may be positioned towards the
right or the left in order to achieve the best possible
installation (
see figure
).
Connecting the water inlet hose
To a suitable cold water connection point: before
attaching the hose, run the water until it is perfectly
clear so that any impurities that may be present in the
water do not clog the appliance; after performing this
operation, screw the inlet hose tightly onto a tap with
a ¾ gas threaded connection.
To a suitable hot water connection point: your
dishwasher may be provided with hot water from the
mains supply (if you have a central heating system
with radiators) provided that it does not exceed a
temperature of 60°C.
Screw the hose to the tap as described for
connection to a cold water supply.
If the inlet hose is not long enough, contact a
specialist store or an authorised technician (
see
Assistance
).
The water pressure must be within the values
indicated in the Technical data table (
see below
).
The hose should not be bent or compressed.
Anti-flooding protection
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the
water supply in the event of anomalies or leaks from
inside the appliance.
- is provided with a
Water Stop
* safety device, in other
words it has a water inlet hose that consists of a
transparent hose on the outside and a red hose on the
inside: both the hoses can withstand extremely high
pressure. If the internal hose breaks, the external hose
becomes a bright red colour and carries the water
instead, thus avoiding any leakage.
It is very important to check the external hose
regularly: if it is a bright red colour, it must be replaced
by an authorised technician as soon as possible (
see
Assistance
).
WARNING: HAZARDOUS VOLTAGE!
Under no circumstance should the water inlet hose be
cut as it contains live electrical parts.
* Only available in selected models.
Installation
3
EN
Connecting the water outlet hose
Connect the outlet hose (without bending it) to a drain
duct with a minimum diameter of 4 cm. Alternatively, rest
it over a sink or tub; the free end of the hose should not
remain immersed in water.
The special plastic elbow*
makes it easier to find the
best layout: fix the elbow to
the wall securely in order to
prevent the outlet hose from
moving and spilling the dirty
water.
The part of the hose marked
with the letter A should be
between 40 and 100 cm
above the ground (
see
figure
).
We advise against the use of hose extensions.
Electrical connection
Before inserting the plug into the electrical socket, make
sure that:
the socket is earthed and complies with current
regulations;
the socket can withstand the maximum load of the
appliance, which is indicated on the data plate
located on the inside of the door (
see Description of
the appliance
);
the power supply voltage falls within the values
indicated on the data plate on the inside of the door;
the socket is compatible with the plug of the
appliance. If this is not the case, ask an authorised
technician to replace the plug (
see Assistance
); do
not use extension cables or multiple sockets.
Once the appliance has been installed, the power
supply cable and the electrical socket should be easily
accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be
replaced by the manufacturer or its Technical Assistance
Service in order to prevent all potential hazards. (See
Assistance)
The Company shall not be held responsible for any
incidents that occur if these regulations are not
observed.
Advice regarding the first wash cycle
After the appliance has been installed, immediately
before running the first wash cycle, completely fill the
salt dispenser with water and add approximately 2 kg of
salt (
see Rinse aid and refined salt
). The water may
overflow: this is normal and is not a cause for concern.
It is also normal that the LOW SALT* indicator light
continues to flash for a few cycles after the salt has been
loaded.
* Only available in selected models.
Technical data
A
Dimensions
width 45 cm
height 85 cm
depth 60 cm
Capacity 9 standard place-settings
Water supply
pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
4.3 psi – 145 psi
Power supply
voltage See appliance data plate
Total absorbed
power See appliance data plate
Fuse See appliance data plate
This dishwasher conforms to
the following European
Community Directives:
-73/23/EEC dated 19/02/73
(Low Voltage) and subsequent
modifications
-89/336/EEC dated 03/05/89
(Electromagnetic Compatibility)
and subsequent modifications
-97/17/EC (Labelling)
-2002/96/ CE Waste Electrical
and Electronic Equipment
(WEEE)


Product specificaties

Merk: Hotpoint-Ariston
Categorie: Vaatwassers
Model: LL 40 EU.C/HA

Heb je hulp nodig?

Als je hulp nodig hebt met Hotpoint-Ariston LL 40 EU.C/HA stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Vaatwassers Hotpoint-Ariston

Handleiding Vaatwassers

Nieuwste handleidingen voor Vaatwassers