Hotpoint-Ariston LFFA plus 8M14 Handleiding

Hotpoint-Ariston Vaatwasser LFFA plus 8M14

Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint-Ariston LFFA plus 8M14 (84 pagina's) in de categorie Vaatwasser. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/84
1
Operating instructions
Contents
Installation, 2-3
Positioning and levelling
Connecting the water and electricity supplies
Advice regarding the first wash cycle
Technical data
Ecodesign Regulation
Description of the appliance, 4
Overall view
Control panel
Loading the racks, 5
Lower rack
Cutlery basket
Upper rack
Start-up and use, 6-7
Starting the dishwasher
Measuring out the detergent
Wash options
Wash cycles, 8
Table of wash cycles
Rinse aid and refined salt, 9
Measuring out the rinse aid
Measuring out the refined salt
Care and maintenance, 10
Shutting off the water and electricity supplies
Cleaning the dishwasher
Preventing unpleasant odours
Cleaning the sprayer arms
Cleaning the water inlet filter
Cleaning the filters
Leaving the machine unused for extended periods
Precautions, advice and Assistance,11
General safety
Disposal
Saving energy and respecting the environment
Assistance
Troubleshooting, 12
English,1
EN
DISHWASHER
LFFA+ 8M14
ES
PT
Español, 49 Português, 61
FR
DE
NL
Français, 13 Deutsch, 25
Nederland,37
Ελληνικά, 73
EL
EN
2
Installation
Keep this instruction manual in a safe place for future
reference. If the appliance is sold, given away or moved, please
ensure the manual is kept with the machine, so that the new
owner may benefit from the advice contained within it.
Please read this instruction manual carefully: it contains
important information regarding the safe installation, use and
maintenance of the appliance.
If the appliance must be moved at any time, keep it in an
upright position; if absolutely necessary, it may be tilted onto its
back.
This appliance is intended to be used in household and
similar applications such as:
- staff kitchen areas in shops, offices and other working
environments;
- farm houses;
- by clients in hotels, motels and other residential type
environments;
- bed and breakfast type environments.
Positioning and levelling
1. Remove the appliance from all packaging and check that it
has not been damaged during transportation.
If it has been damaged, contact the retailer and do not proceed
any further with the installation process.
2. Check the dishwasher by placing it so that its sides or back
panel are in contact with the adjacent cabinets or even with the
wall. This appliance can also be recessed under a single
worktop* (
see the Assembly instruction sheet
).
3. Position the dishwasher on a level and sturdy floor. If the floor
is uneven, the front feet of the appliance may be adjusted until it
reaches a horizontal position. If the appliance is levelled correctly,
it will be more stable and much less likely to move or cause
vibrations and noise while it is operating.
4*. Adjust the height of the rear foot from the front of the appliance
on the central lower part of the dishwasher, turning a hexagonal
spanner (red color) with an opening of 8 mm in a clockwise
direction to increase the height or in an anticlockwise direction to
decrease the height.
Connecting the water and electricity
supplies
Connection to the water and electricity supplies should only
be performed by a qualified technician.
The dishwasher should not stand on top of the water hoses
or the electricity supply cable.
The appliance must be connected to the water supply
network using new hoses.
Do not use old hoses.
The water inlet and outlet hoses and the electricity supply cable
may be positioned towards the right or the left in order to achieve
the best possible installation.
Connecting the water inlet hose
To a suitable cold water connection point: before attaching the
hose, run the water until it is perfectly clear so that any impurities
that may be present in the water do not clog the appliance;
after performing this operation, screw the inlet hose tightly
onto a tap with a ¾ gas threaded connection.
To a suitable hot water connection point: your dishwasher
may be supplied with hot water from the mains supply (if you
have a central heating system with radiators) provided that it
does not exceed a temperature of 60°C.
Screw the hose to the tap as described for connection to a
cold water supply.
If the inlet hose is not long enough, contact a specialist store
or an authorised technician (
see Assistance
).
The water pressure must be within the values indicated in the
Technical data table (
see adjacent information
).
The hose should not be bent or compressed.
Connecting the water outlet hose
Connect the outlet hose (without bending it) to a drain duct
with a minimum diameter of 4 cm.
The outlet hose must be at a height ranging from 40 to 80
cm from the floor / surface where the dishwasher rests (A).
Before connecting the water outlet hose to the sink drain,
remove the plastic plug (B).
Anti-flooding protection
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the water supply
in the event of anomalies or leaks from inside the appliance.
Some models are also equipped with the supplementary safety
device
New Acqua Stop
*, which guarantees anti-flooding
protection even in the event of a supply hose rupture.
WARNING: HAZARDOUS VOLTAGE!
Under no circumstance should the water inlet hose be cut as it
contains live electrical parts.
* Only available in selected models.
EN
3
Electrical connection
Before inserting the plug into the electrical socket, make sure
that:
The socket is earthed and complies with current regulations.
The socket can withstand the maximum load of the appliance,
which is indicated on the data plate located on the inside of the
door (
see chapter entitled Description of the appliance
).
The power supply voltage falls within the values indicated on
the data plate on the inside of the door.
The socket is compatible with the plug of the appliance. If this
is not the case, ask an authorised technician to replace the
plug (
see Assistance
); do not use extension cables or multiple
sockets.
Once the appliance has been installed, the power supply
cable and the electrical socket should be easily accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be replaced
by the manufacturer or its Technical Assistance Service in order to
prevent all potential hazards. (See Assistance)
The Company shall not be held responsible for any incidents
that occur if these regulations are not observed.
Anti-condensation strip*
After installing the dishwasher, open the door and stick the
adhesive transparent strip under the wooden shelf in order to
protect it from any condensation which may form.
Advice regarding the first wash cycle
After the appliance has been installed, immediately before running
the first wash cycle, completely fill the salt dispenser with water
and add only then approximately 1 kg of salt (
see chapter entitled
Rinse aid and refined salt
). The water may overflow: this is normal
and is not a cause for concern. Select the water hardness value
(
see chapter entitled Rinse aid and refined salt
). - After the salt
has been poured into the machine, the LOW SALT indicator
light* switches off.
If the salt container is not filled, the water softener and the
heating element may be damaged as a result.
Technical data
Dimensions
width 60 cm
height 85 cm
depth 60 cm
Capacity 14 standard place-settings
Water supply
pressure
0,05 ÷ 1MPa (0.5 ÷ 10 bar)
7,25 – 145 psi
Power supply
voltage See appliance data plate
Total absorbed
power See appliance data plate
Fuse See appliance data plate
This dishwasher conforms to the
following European Community
Directives:
-2006/95/EC (Low Voltage)
-2004/108/EC (Electromagnetic
Compatibility)
-2005/32/EC (Comm. Reg.
1275/2008) (Ecodesign)
-97/17/EC (Labelling)
-2002/96/EC Waste Electrical
and Electronic Equipment
(WEEE)
ECODESIGN REGULATION
ECO wash cycle is the standard cycle to which the energy label data refers; this cycle can be used to wash crockery with a normal
soil level and is the most efficient in terms of energy and water consumption for this type of crockery. To reduce consumption even
further, only run the dishwasher when it is full.
Standby consumption: Left-on mode consumption: 3 W Off mode consumption: 1,3 W
Consumption data table for the main cycles
* Cycle data refers to the values recorded in a laboratory, in accordance with European standard EN 50242.
** Data is obtained by recording values when the appliance is operational and loaded with user crockery.
Standard conditions* User conditions**
Energy consumption
(kWh/cycle)
Water consumption
(l/cycle)
Duration
(min/cycle)
Energy consumption
(kWh/cycle)
Water consumption
(l/cycle)
Duration
(min/cycle)
INTENSIVE 1,65 16 150 1,45 15 135
NORMAL 1,35 16 120 1,20 15 110


Product specificaties

Merk: Hotpoint-Ariston
Categorie: Vaatwasser
Model: LFFA plus 8M14

Heb je hulp nodig?

Als je hulp nodig hebt met Hotpoint-Ariston LFFA plus 8M14 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Vaatwasser Hotpoint-Ariston

Handleiding Vaatwasser

Nieuwste handleidingen voor Vaatwasser