Hotpoint-Ariston CISPF 640 E IX/HA Handleiding

Hotpoint-Ariston Fornuis CISPF 640 E IX/HA

Lees hieronder de 📖 handleiding in het Nederlandse voor Hotpoint-Ariston CISPF 640 E IX/HA (24 pagina's) in de categorie Fornuis. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/24
HOB
CISPF 640 E IX/HA
Contents
Installation, 2-5
Positioning
Electrical connection
Gas connection
Data plate
Burner and nozzle specifications
Description of the appliance, 6
Overall view
Start-up and use, 7
Practical advice on using the burners
Practical advice on using the electric hotplates
Precautions and tips, 8
General safety
Disposal
Maintenance and care, 9
Switching the appliance off
Cleaning the appliance
Gas tap maintenance
Troubleshooting, 10
Operating Instructions
GB
English, 1
GB RS
Ðóññêèé,11
GB
2
Before operating your new appliance please read this
instruction booklet carefully. It contains important information
for safe use, installation and care of the appliance.
Please keep these operating instructions for future
reference. Pass them on to possible new owners of the
appliance.
Positioning
Keep packaging material out of the reach of children. It
can become a choking or suffocation hazard (see
Precautions and tips).
The appliance must be installed by a qualified professional
according to the instructions provided. Incorrect installation
may cause harm to people and animals or may damage
property.
This unit may be installed and used only in permanently
ventilated rooms in accordance with British Standard Codes
Of Practice: B.S. 6172 / B.S. 5440, Par. 2 and B.S. 6891
Current Editions. The following requirements must be
observed:
The room must be equipped with an air extraction system
that expels any combustion fumes. This may consist of a
hood or an electric fan that automatically starts each time
the appliance is switched on.
The room must also allow proper air circulation, as air is
needed for combustion to occur normally. The flow of air
must not be less than 2 m3/h per kW of installed power.
The air circulation system may
take air directly from the outside
by means of a pipe with an inner
cross section of at least 100 cm2;
the opening must not be
vulnerable to any type of
blockages.
The system can also provide the
air needed for combustion
indirectly, i.e. from adjacent rooms
fitted with air circulation tubes as
described above. However, these
rooms must not be communal
rooms, bedrooms or rooms that
may present a fire hazard.
Liquid petroleum gas sinks to the floor as it is heavier
than air. Therefore, rooms containing LPG cylinders must
also be equipped with vents to allow gas to escape in the
event of a leak. As a result LPG cylinders, whether
partially or completely full, must not be installed or stored
in rooms or storage areas that are below ground level
(cellars, etc.). It is advisable to keep only the cylinder
being used in the room, positioned so that it is not
subject to heat produced by external sources (ovens,
fireplaces, stoves, etc. ) which could raise the
temperature of the cylinder above 50°C.
Fitting the appliance
Gas and mixed hobs are manufactured with type X
degree protection against overheating. The following
precautions must be taken when installing the hob:
Kitchen cabinets adjacent to the appliance and taller
than the top of the hob must be at least 600 mm from the
edge of the hob.
Hoods must be installed according to their relative
installation instruction manuals and at a minimum
distance of 650 mm from the hob.
Place the wall cabinets adjacent to the hood at a
minimum height of 420 mm from the hob (see figure).
If the hob is installed beneath a
wall cabinet, the latter must be
situated at a minimum of 700 mm
above the hob (see figure).
The installation cavity should have the dimensions
indicated in the figure.
Fastening hooks are provided, allowing you to fasten the
hob to tops that are between 20 and 40 mm thick. To
ensure the hob is securely fastened to the top, we
recommend you use all the hooks provided.
555
mm
475
mm
55
mm
Hook fastening diagram
Hooking position Hooking position
for top H=20 mm for top H=30 mm
Installation
Enlarging the ventilation slot
between window and floor.
Adjacent
Room
Room to be
Vented
A
Examples of ventilation holes
for comburant air.
In a chimney stack or branched flue.
(exclusively for cooking appliances)
Directly to
the Outside
600mm min.
540mm min.
700mm min.
GB
3
Front
Hooking position Back
for top H=40 mm
Use the hooks contained in theaccessory pack
Where the hob is not installed over a built-in oven, a
wooden panel must be installed as insulation. This must
be placed at a minimum distance of 20 mm from the
lower part of the hob.
Ventilation
To ensure adequate ventilation, the back panel of the
cabinet must be removed. It is advisable to install the oven
so that it rests on two strips of wood, or on a completely flat
surface with an opening of at least 45 x 560 mm (see
diagrams).
Where a hob is installed above an oven without a forced
ventilation cooling system, adequate ventilation must be
provided inside the cabinet by means of air holes through
which air can pass (see figure).
Electrical connection
Hobs equipped with a three-pole power supply cable are
designed to operate with alternating current at the voltage
and frequency indicated on the data plate (this is located on
the lower part of the appliance). The earth wire in the cable
has a green and yellow cover. If the appliance is to be
installed above a built-in electric oven, the electrical
connection of the hob and the oven must be carried out
separately, both for electrical safety purposes and to make
extracting the oven easier.
Connecting the supply cable to the mains
Install a standardised plug corresponding to the load
indicated on the data plate.
The appliance must be directly connected to the mains using
an omnipolar circuit-breaker with a minimum contact opening
of 3 mm installed between the appliance and the mains. The
circuit-breaker must be suitable for the charge indicated and
must comply with current electrical regulations (the earthing
wire must not be interrupted by the circuit-breaker). The
supply cable must not come into contact with surfaces with
temperatures higher than 50°C.
The installer must ensure that the correct electrical
connection has been made and that it is compliant with
safety regulations.
Before connecting to the power supply, make sure that:
The appliance is earthed and the plug is compliant with
the law.
The socket can withstand the maximum power of the
appliance, which is indicated on the data plate.
The voltage is in the range between the values indicated
on the data plate.
The socket is compatible with the plug of the appliance. If
the socket is incompatible with the plug, ask an
authorised technician to replace it. Do not use extension
cords or multiple sockets.
Once the appliance has been installed, the power supply
cable and the electrical socket must be easily accessible.
The cable must not be bent or compressed.
The cable must be checked regularly and replaced by
authorised technicians only (see Assistance).
The manufacturer declines any liability should these safety
measures not be observed.
Gas connection
The appliance should be connected to the main gas supply
or to a gas cylinder in compliance with current national
regulations. Before carrying out the connection, make sure
the cooker is compatible with the gas supply you wish to
use. If this is not the case, follow the instructions indicated in
the paragraph Adapting to different types of gas.
When using liquid gas from a cylinder, install a pressure
regulator which complies with current national regulations.
Check that the pressure of the gas supply is consistent
with the values indicated in Table 1 (Burner and nozzle
specifications). This will ensure the safe operation and
longevity of your appliance while maintaining efficient
energy consumption.
Connection with a rigid pipe (copper or steel)
Connection to the gas system must be carried out in
such a way as not to place any strain of any kind on the
appliance.
560 mm.
45 mm.

Product specificaties

Merk: Hotpoint-Ariston
Categorie: Fornuis
Model: CISPF 640 E IX/HA

Heb je hulp nodig?

Als je hulp nodig hebt met Hotpoint-Ariston CISPF 640 E IX/HA stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Fornuis Hotpoint-Ariston

Hotpoint-Ariston

Hotpoint-Ariston PH 640MST (OG)/HA Handleiding

4 Juni 2023
Hotpoint-Ariston

Hotpoint-Ariston PF 640 ES (AX)/HA Handleiding

1 Juni 2023
Hotpoint-Ariston

Hotpoint-Ariston PZ 750 R GH Handleiding

31 Mei 2023
Hotpoint-Ariston

Hotpoint-Ariston PCN 752 T/EX/HA Handleiding

28 Mei 2023
Hotpoint-Ariston

Hotpoint-Ariston PCN 751 T/IX/HA Handleiding

27 Mei 2023
Hotpoint-Ariston

Hotpoint-Ariston PK 750 TL GH /HA Handleiding

26 Mei 2023
Hotpoint-Ariston

Hotpoint-Ariston TQ 751 S (ICE) IX/HA Handleiding

24 Mei 2023
Hotpoint-Ariston

Hotpoint-Ariston CX65SP1 (W) I /HA Handleiding

24 Mei 2023
Hotpoint-Ariston

Hotpoint-Ariston PC 640 (WH)/HA Handleiding

22 Mei 2023
Hotpoint-Ariston

Hotpoint-Ariston PCN 641 T/IX/HA Handleiding

19 Mei 2023

Handleiding Fornuis

Nieuwste handleidingen voor Fornuis

AEG

AEG NCP84C01AZ Handleiding

28 April 2024
AEG

AEG TI64IB30IZ Handleiding

28 April 2024
Midea

Midea MC-HV848 Handleiding

28 April 2024
IKEA

IKEA TILLREDA 005.558.96 Handleiding

27 April 2024
IKEA

IKEA MATMÄSSIG 905.136.04 Handleiding

27 April 2024
IKEA

IKEA VASASTAN 405.236.05 Handleiding

27 April 2024
Bertazzoni

Bertazzoni PRO1005GGVLXE Handleiding

25 April 2024
Bertazzoni

Bertazzoni P905CAPROX Handleiding

25 April 2024
Mestic

Mestic MIC-120 Handleiding

25 April 2024
LG

LG LCE3010SBE Handleiding

18 April 2024