Honeywell Performance HEW2PER2 Handleiding

Bekijk gratis de handleiding van Honeywell Performance HEW2PER2 (2 pagina’s), behorend tot de categorie Bewakingscamera. Deze gids werd als nuttig beoordeeld door 14 mensen en kreeg gemiddeld 4.9 sterren uit 2 reviews. Heb je een vraag over Honeywell Performance HEW2PER2 of wil je andere gebruikers van dit product iets vragen? Stel een vraag

HEW2PER2 WDR 4 MP IR Bullet Camera

Quick Installation Guide

Thank you for purchasing aHoneywell Performance Series IP

camera. Follow the instructions in this guide to install and log in

to your camera. For instructions on configuring the camera,

refer to the Performance Series IP Cameras User Guideon the

installation CD that came with your camera.

If you require additional assistance, contact Tech Support

(contact info is listed on the back page).

Cautions and Warnings

WARNING

To ensure compliance with electrical safety standards, this product is intended for

use with a Listed Power Adapter marked “Limited Power Source” or “LPS” on the unit,

output rated to 12 VDC, minimum 0.33 A, TMA=60 deg C, or from Power over

Ethernet (PoE) provided by Listed Information Technology Equipment meeting IEEE

802.3af PoE standard.

WARNING

The Ethernet connection is not intended to be connected to exposed (outside plant)

networks. Do not connect two power sources to the camera at the same time.

CAUTION

Invisible LED radiation (850 nm). Avoid exposure to beam.

Important Safeguards

•Read and keep these instructions.

•Do not aim the camera toward a bright light source for extended periods to prevent damage to

the imager. Avoid operating the unit under or close to unstable light sources (may cause

flickering), or close to fluorescent lamps or objects reflecting light.

•Do not touch the camera lens.

•Do not drop the camera or subject it to physical shock.

•Do not use a strong or abrasive detergent when cleaning the camera.

•Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where

the operating temperature is outside the recommended range of -22°F to 140°F (–30°C to

60°C).

Note

Do not apply power to the camera before completing installation.

Confirm the installation surface can support at least three times the weight of the

camera.

Before You Begin

Before you begin, check that you have received all of the parts listed below. If any parts are missing

or damaged, contact your dealer immediately.

•Camera

•Installation CD

•Quick installation guide

•Allen key (L- wrench)

•Self-tapping screws (×4)

•Plastic wall anchors (×4)

•Mounting template

Preparing the Mounting Surface

Inspect the site where you want to install the camera. The mounting

surface must be flat and capable of supporting at least three times

the weight of the camera.

Remove the backing from the mounting template sticker and affix

the sticker to the mounting surface.

NoteIf you are using the side exit for the cable, note the

orientation of the cable exit notch. In outdoor installations the notch

should point downwards to prevent water from entering the camera

housing.

Drill three screw holes at the locations indicated on the mounting

template sticker and insert the three supplied plastic anchors in the

holes.

If you are flush mounting the camera and want to store the cables

inside the wall or ceiling, drill a hole at the cable exit position on the

mounting template and then pull the cables through the hole.

CAUTION

THIS SYMBOL INDICATES THAT

DANGE OUSRVOLTAGE

CONSTITUTING A RISK OF

ELECTRIC SHOCK IS PRESENT

WITHIN THE UNIT.

CA:TUTIONO REDUCETHE RISK OF ELECTRIC

SHOCK, DO NOT REMTHE COVEOVER.

NO USER-SERVICEABLE PAR.TS INSIDE

REFER SERTOQURVICINGALIFIED SEVICE

PERSONNEL.

THIS SYMBOL INDICATESTHAT

IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS

ACCOMPANYT.THIS UNI

RISK OF ELECTRIC

SHOCK

DO NT OPENO

Product specificaties