Honeywell HSF1630B Handleiding

Honeywell Ventilator HSF1630B

Lees hieronder de 📖 handleiding in het Nederlandse voor Honeywell HSF1630B (12 pagina's) in de categorie Ventilator. Deze handleiding was nuttig voor 71 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12
12" OSCILLATING TABLE FAN
Model HTF1220 Series
16" OSCILLATING STAND FAN
Model HSF1630 Series
When using electrical appliances,
basic precautions should always
be followed to reduce the risk of
fire, electric shock, and injury to
persons, including the following:
1. Use this fan only as described in this manual.
Other use not recommended may cause
fire, electric shock or injury to persons.
2. This product is intended for household
use ONLY and not for commercial,
industrial or outdoor use.
3. To protect against electric shock, DO NOT
place fan in window, immerse unit, plug or
cord in water or spray with liquids.
4. This appliance has a polarized plug (one blade
is wider than the other). To reduce the risk of
shock, this plug is intended to fit only one way
in a polarized outlet. If the plug does not fit
fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician.
DO NOT attempt to defeat this safety feature.
5. Close supervision is necessary when any
appliance is used by or near children.
6. OFF Press the button and unplug the fan
from the outlet when not in use, when moving
the fan from one location to another and
before cleaning.
7. To disconnect the fan, first press the
OFF button, grip the plug and pull it from
the wall outlet. pull by the cord.NEVER
8. DO NOT operate the fan in the presence
of explosive and/or flammable fumes.
9. DO NOT place the fan or any parts near an
open flame, cooking or other heating appliance.
10. DO NOT operate the fan with damaged cord or
plug or if the product malfunctions, is dropped
or damaged in any manner (see warranty).
11. Avoid contact with moving fan parts.
12. The use of attachments not recommended
by the manufacturer may be hazardous.
13. Place the fan on a dry, level surface.
14. DO NOT hang or mount fan on a wall or ceiling.
15. DO NOT operate if the fan housing is removed
or damaged.
16. A loose fit between the AC outlet (receptacle)
and plug may cause overheating and a
distortion of the plug. Contact a qualified
electrician to replace loose or worn outlet.
17. DO NOT DO NOT run fan cord under carpeting.
cover cord with throw rugs, runners, or similar
coverings. DO NOT route cord under furniture
or appliances. Arrange cord away from traffic
areas and where it will not be tripped over.
WARNING: To Reduce The Risk of Fire or
Electric Shock, DO NOT Use This Fan With
Any Solid-State Speed Control Device.
IMPORTANT
SAFETY INSTRUCTIONS
READ AND SAVE THESE
SAFETY INSTRUCTIONS
BEFORE USING THIS FAN
2
BASE ASSEMBLY – HTF1220 SERIES
PART GUIDE – HTF1220 SERIES
1. Front Grille
2. Blade
3. Plastic Nut
4. Rear Grille
5. Motor Shaft
6. Oscillation Knob
7. Fan Body
8. Blade Nut
9. Speed Control Buttons
10. Base
11. Grille Locking Clips
12. Fan Head Assembly
13. Prongs
FUSED SAFETY PLUG - FOR US MODELS ONLY
USER SERVICING INSTRUCTIONS
• If your fan loses power and you suspect that the fuse on your fan has
blown, grasp plug and remove from the receptacle or other outlet device.
DO NOT unplug by pulling on cord.
• Slide fuse cover, located on the top of the plug towards the prongs of
the plug. (Fig. 1)
• Carefully remove the blown fuse and snap a new fuse into place. To
Reduce the Risk of Fire, replace fuse only with 2.5 Amp, 125 volt fuse.
Fully close the fuse door by sliding back into place. (Fig. 2) Discard the
blown fuse. The plug should now be ready for normal use.
• To Reduce the Risk of Fire, DO NOT replace attachment plug. Contains
a safety device (fuse) that should not be removed. Discard product if
the attachment plug is damaged.
• If you need further information on how or when to replace the fuse in
the safety plug, please contact Kaz Consumer Relations Department
by visiting our website at www.honeywellpluggedin.com/fans
or calling 1-800-477-0457.
This fan features a fused safety plug which is designed to cut off electric current to the fan if an electrical
fault occurs. Please see below for more information on how to properly use your fan and replace the safety
plug fuse, if needed.
Fig. 1
Fig. 2
7
10
9
2
3
4
5
13
12
1
6
8
11
4
• Place your fan on a level and dry surface.
• Plug the power cord into a polarized 120 Volt AC wall outlet. Please make sure the speed control
is in the off position.
Speed Control Speed is controlled by pressing the Control Pad button to the desired setting
- Off - Low - Med - High
Oscillation Control To make the fan oscillate, push down on the oscillation knob located on the top of the
motor housing. To stop the fan from oscillating, pull up on the oscillation knob when
the fan is in the desired position.
Tilt Control The airflow can be adjusted upward or downward by tilting the fan head as desired.
To change the tilting angle of the fan head assembly, simply move the fan head to
the desired angle.
Turn the pole locking nut to loosen the pole. Adjust the pole to counterclockwise
the desired height and firmly tighten the locking nut in a clockwise directi
on.
OPERATION
CLEANING AND STORAGE
CLEANING AND STORAGE (CONTINUED)
• UNPLUG the fan before cleaning.
• Use only a soft, damp cloth to gently wipe the fan clean.
• DO NOT immerse the fan in water and allow water to drip into the motor housing. NEVER
• DO NOT use gasoline, paint thinner or other chemicals to clean the fan.
Height Adjustment
(HSF1630 series only)
BASE ASSEMBLY – HSF1630 SERIES
1. Create an X with the 2 cross base pieces.
2. Place the main pole onto the cross base, align with the four holes. Use the four screws provided to
secure and tighten the pole to the cross base.
3. Remove the pole locking nut and slide the base sheath over the main pole and onto the cross base,
replace the pole locking nut.
4. Loosen the pole extension locking nut around the top of the main pole and raise the chrome extension
pole to its desired height. Tighten the pole extension locking nut.
5. Position the fan head assembly onto the extension pole and tighten the locking screw.
ASSEMBLY OF THE BLADE AND GRILLES – HSF1630 SERIES
1. Unscrew the blade nut clockwise and the plastic nut counterclockwise and set aside.
2. Position the rear grille onto the fan head assembly making sure the two alignment holes are aligned
with the two prongs.
3. Screw on plastic nut tightly clockwise to attach rear grille.
4. Install the blade onto the shaft until the retaining pin fits into the notch on the blade.
5. Screw blade nut to the motor shaft counterclockwise (tighten by turning to the left).
6. Mount the front grille and secure using the locking clips.

Product specificaties

Merk: Honeywell
Categorie: Ventilator
Model: HSF1630B

Heb je hulp nodig?

Als je hulp nodig hebt met Honeywell HSF1630B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Ventilator Honeywell

Honeywell

Honeywell CL40 Handleiding

20 Februari 2024
Honeywell

Honeywell Sunset Key 10288 Handleiding

18 December 2023
Honeywell

Honeywell Wicker Park 10268 Handleiding

18 December 2023
Honeywell

Honeywell Elston 10290 Handleiding

18 December 2023
Honeywell

Honeywell Eastover 10214 Handleiding

18 December 2023
Honeywell

Honeywell Tech Force HT-9700 Handleiding

18 December 2023
Honeywell

Honeywell Glen Alden 50183 Handleiding

18 December 2023
Honeywell

Honeywell Glen Alden 50182 Handleiding

18 December 2023
Honeywell

Honeywell Glen Alden 50180 Handleiding

18 December 2023
Honeywell

Honeywell Blufton 10283 Handleiding

18 December 2023

Handleiding Ventilator

Nieuwste handleidingen voor Ventilator

LC-Power

LC-Power LC-CFC-2 Handleiding

25 April 2024
Bimar

Bimar VB50 Handleiding

25 April 2024
Bimar

Bimar VPC100 Handleiding

25 April 2024
Bimar

Bimar VI94 Handleiding

22 April 2024
Livoo

Livoo DOM488 Handleiding

20 April 2024
GoldAir

GoldAir GAS10 Handleiding

17 April 2024
Heller

Heller HHDF23S Handleiding

17 April 2024
GoldAir

GoldAir GCTF530 Handleiding

16 April 2024
Gamdias

Gamdias Aeolus M2-1201 Handleiding

16 April 2024
Gamdias

Gamdias Aeolus M3-1204R Handleiding

16 April 2024