Honeywell C7189R Handleiding
Honeywell
Thermostaat
C7189R
Bekijk gratis de handleiding van Honeywell C7189R (20 pagina’s), behorend tot de categorie Thermostaat. Deze gids werd als nuttig beoordeeld door 19 mensen en kreeg gemiddeld 4.7 sterren uit 10 reviews. Heb je een vraag over Honeywell C7189R of wil je andere gebruikers van dit product iets vragen? Stel een vraag
Pagina 1/20
Installation
Guide
C7189R
Wireless Indoor Sensor
Capteur d’intérieur sans fil
Sensor inalámbrico para interiores
69-2459EFS-05
Installation Guide
ii
69-2459EFS—05
® U.S. Registered Trademark.
Copyright © 2012 Honeywell International Inc.
All rights reserved.
About your wireless indoor sensor
This sensor monitors temperature and humidity in any indoor location and transmits it
wirelessly to the thermostat.
You can set the system to monitor temperature at the thermostat, or at the sensor location,
or use an average of both to optimize comfort throughout the home. The thermostat can
use up to 6 wireless indoor sensors.
When multiple sensors are installed, the thermostat can monitor temperature and humidity
in separate locations. For example, one sensor can control humidication on the main level,
while another controls dehumidication in a crawl space. For more information, see the
instructions provided with the thermostat.
Note: The wireless indoor sensor is compatible only with RedLINK 2.0 thermostats.
Operating Ambient Temperature: 0 to 120° F (-17.8 to 48.9° C)
For Optimal Battery Life: 35 to 114° F (1.7 to 45.6° C)
Operating Relative Humidity: 5% to 90% (non-condensing)
Physical Dimensions: 2-7/8 x 1-7/8 x 15/16 inches (74 x 48 x 24 mm)
The thermostat will display a warning to replace batteries in the indoor sensor about 2 months
before power is depleted. The sensor status light will begin flashing red about 2–3 weeks before
power is depleted. During normal operation, the status light remains off.
Wireless Indoor Sensor
169-2459EFS—05
MCR32933
MCR32934 MCR32935
Install 2 fresh AAA alkaline batteries.
Status light will briefly flash green. If it
flashes red, batteries are not good.
Install batteries and link sensor to thermostat
1
Install batteries, then enter Wireless Setup mode at the thermostat. Press and
release the CONNECT button to link the wireless sensor to the thermostat.
Press and release CONNECT.
After a short delay, the status light
will glow green for 15 seconds.
If the status light is red, the
sensor did not link with the
thermostat. See Note.
Verify the thermostat is in the Wireless Setup
mode and the indoor sensor is at least 2 feet
away from the EIM or thermostat.
Product specificaties
| Merk: | Honeywell |
| Categorie: | Thermostaat |
| Model: | C7189R |
Heb je hulp nodig?
Als je hulp nodig hebt met Honeywell C7189R stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Thermostaat Honeywell
4 Juli 2025
4 Juli 2025
9 Juni 2025
10 Juni 2024
27 Februari 2024
2 September 2023
9 Juli 2023
7 Juli 2023
7 Juli 2023
6 Juli 2023
Handleiding Thermostaat
- Thermy
- Agpo Ferroli
- Bulex
- Emerson
- Profile
- Johnson Control
- Konyks
- Saunier Duval
- ACV
- Ferguson
- Gira
- Vasco
- Velleman
- Hugo Muller
Nieuwste handleidingen voor Thermostaat
31 Juli 2025
30 Juli 2025
29 Juli 2025
29 Juli 2025
28 Juli 2025
28 Juli 2025
28 Juli 2025
28 Juli 2025
28 Juli 2025
28 Juli 2025