Holman EzySpray 5L Handleiding

Bekijk gratis de handleiding van Holman EzySpray 5L (4 pagina’s), behorend tot de categorie Niet gecategoriseerd. Deze gids werd als nuttig beoordeeld door 356 mensen en kreeg gemiddeld 4.4 sterren uit 8 reviews. Heb je een vraag over Holman EzySpray 5L of wil je andere gebruikers van dit product iets vragen? Stel een vraag

2

D

3a

2a



Do not attempt to unscrew

the PRESSURETANK lid–

doing so will break the

pressurised seal and

void your warranty!

COMPONENTS

A. SPRAY HEAD

B. WAND

C. TRIGGER

D. HOSE

E. EzySpray®PRESSURETANK

F. WAND THREAD

G. LOCKING NUT

H. TANK OUTLET

I. PRESSURE GAUGE

J. SCHRADER VALVE

K. 12mm HOSE CONNECTION

L. PRESSURE RELEASE VALVE

M. GRAB HANDLE

N. PLUNGER

O. TANK OPENING

P. INLET VALVE CONNECTOR

INTRODUCTION

The portable and lightweight

HOLMAN EzySpray® is an essential tool

for your garden maintenance. The patented

pre-pressurised air tank requires no

manual pumping–connect your garden

hose, fill the reservoir, and away you go!

A standard garden spray would require

manual pumping roughly 1,250 times

for 50L of spraying; the EzySpray

®

doesn’t need a single pump.

To fill your EzySpray®, simply connect

a garden hose to the tank. The gauge

indicates how full the tank is, and the spray

wand gives all the control you need.

Adding fertiliser, herbicide or other additives to

your EzySpray®is easy. Unhook the handle, and

pour in concentrate before filling with water.

For more info and support, visit

www.holmanindustries.com.au

I

2

SPRAY HOSE CONNECTION

a. Remove the protective end cap from the ()TANKOUTLET H

b. Screw one end of the () onto the HOSEDTANKOUTLET H ()

c. Screw the other end of the onto the threaded HOSE

end of the SPRAYWAND assembly

LFor the easiest assembly, be sure to screw the hose onto

the tank outlet screwing onto the spray wandbefore

1

SPRAY WAND ASSEMBLY

a. Screw the SPRAY HEAD() onto the AWAND THREAD ()F

b. Loosen (do not remove) the () on the ()LOCKING NUTGTRIGGERC

c. Insert the opposite end of the () through WAND B

the locking nut on the TRIGGER

d. Tighten the locking nut on the TRIGGER

e. This completes the assembly of the SPRAY WAND

A

A

B

F

B

B

C

G

C

2c

D

C

1a

1c

1b

D

J

Need help? Visit www.holmanindustries.com.au/5l-ezyspray/for more product information or support.holmanindustries.com.au/ for additional help Scan me with your phone for more resources!



Your EzySpray® is not suitable

for drinking under any

circumstance

3

TANK PRESSURE CHECK

Before filling your EzySpray®, be sure to check the pressure gauge

a. Locate the () on the side of the PRESSUREGAUGEIPRESSURE TANK ()E

b. Check the pressure gauge reads at least 1 BAR

This is required for the pressurised tank to work correctly

c. If pressure is satisfactory, proceed to Steps 4 and 5

d. If the pressure gauge is low, follow the Re‑pressurise

process in Troubleshooting

Before

filling, the

dial should

read roughly

1bar here

When filling,

the dial will

indicate how

much water is

in the tank

KEEP AIR

NEAR

1 BAR!

WATER

MAX

2

3

45L

B

A

R

0

2 4

5

6

3

AIR LOW

1

L

H

M

Made under license from

Pressuresac Pty Ltd,

Kinglake Australia.

PATENTS

Australia: 2007209766

New Zealand: 569888

United Kingdom: GB2449588

Canada: 2,640,600

P

2a

H

Product specificaties