HiLook TK-4144TH-MH Handleiding

HiLook Bewakingscamera TK-4144TH-MH

Lees hieronder de 📖 handleiding in het Nederlandse voor HiLook TK-4144TH-MH (28 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/28

Quick User Guide

EN — Quick User Guide

Safety Instruction: You must carefully read this safety instructions before using and installing the product.

Warnings & Cautions:

● Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end user.-

● You must be in strict compliance with electrical safety regulations of the nation and region. Firmly connect the plug to the power

socket. Do not connect several devices to one power adapter. Power off the device before connecting and disconnecting

accessories and peripherals.

● Input voltage should meet the SELV (Safety Extra Low Voltage) and the LPS (Limited Power Source) according to the IEC60950 1. -

● If smoke, odor or noise rise from the device, power off at once and unplug the power cable, and then contact the service center.

For Camera:

● Only use accessories recommended by HIKVISION.

● Do not expose the camera directly to high concentrations of X ray, laser or UV radiation. The direct exposure may cause -

permanent damage to the image sensor.

● If the product does NOT work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the

camera yourself.

For DVR/NVR:

● The device is designed for indoor use only. Install it in a well ventilated, dust free environment without liquids.- -

● Properly secure the device to a rack or shelf. Major shocks or jolts may cause damage to the sensitive electronics within the

device.

● Use the device in conjunction with an UPS, and use factory recommended HDD if possible.

Trademarks Acknowledgement

and other Hikvision’s trademarks and logos are the properties of Hikvision in various jurisdictions. Other trademarks and

logos mentioned below are the properties of their respective owners.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND

FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS, AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED,

INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND

NON INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS, EMPLOYEES, OR AGENTS BE LIABLE -

TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR

LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE USE OF

THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. HIKVISION

SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM

CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL PROVIDE

TIMELY TECHNICAL SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS

PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. HIKVISION SHALL NOT BE LI ABLE IN THE EVENT

THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.

PRODUCED BY:

Hangzhou Hikvision Digital Technology Co. Ltd.

Qianmo Road 555, Binjiang District, Hangzhou

310052, China

Made in China

CONTACT INFORMATION IN CHINA:

Hangzhou Hikvision Digital Technology Co. Ltd.

Qianmo Road 555, Binjiang District, Hangzhou

310052, China

Tel: +86 571 8807 5998- - -

Fax: +86 571 8993 5635- - -

EN — Quick User Guide

◆ Get started for the basic usage of analog/network camera, and speed dome.

Step 1. Check the installation environment including cables, tools, and the original packaging.

Step 2. Install the memory card for local storage (if needed).

Step 3. Install the camera/speed dome to the proper place.

Step 4. Connect alarm in/out to the alarm device (if needed)

Step 5. Connect the power supply cables.

Step 6. See the procedures below:

For analog camera: Connect video cable to the VIDEO IN interface in the DVR.

For analog speed dome:

a) Connect video cable to the VIDEO IN interface in the DVR.

b) Connect RS 485 to the DVR. -

c) Set DIP switch for analog speed dome.

For network camera/network speed dome:

a) Connect the network camera to a PC with a network cable.

b) Input the default IP address: 192.168.1.64.

c) Input and confirm your password and Click “ to finish activation.OK”

d) Connect the camera and PC to the same router or the same switch.

e) Login the camera (default IP: 192.168.1.64) via your password.

f) Modify the IP address to the same subnet with connected router/switch.

g) Re- login with the new IP address.

Notes:

⚫ For the network camera which enables the DHCP by default, you need to activate the network camera via SADP software and

search the IP address.

⚫ NVR can also be used to activate and set the network camera.

Step 7. Power on the cameras, DVR/NVR and monitor, then you can view the image on the monitor.

Notes:

⚫ For detailed information, See the Quick Start Guide or User Manual which can be downloaded from www.hikvision.com or

www.hi watch.eu-

⚫ The functions vary depending on the models of network camera.

◆ Get started for the basic usage of digital/network video recorder.

Step 1. Install the HDD.

See detailed installation in the from User Manual www.hikvision.com or

www.hi watch.eu- according to specific model.

Step 2. Connect peripheral devices to the DVR/NVR.

Step 3. Power on the DVR/NVR, and activate it by creating a strong

password and confirming it.

Step 4. Log in to the DVR/NVR, and follow the Setup Wizard to configure

basic parameters.

You can operate and configure the device, including the live view, record

schedule, playback, backup, etc.

Note: For the detailed operation of DVR/NVR, refer to the from User Manual www.hikvision.com www.hi watch.eu or - according

to the specific model.

TECHNICAL SUPPORT

In case of any problem, please immediately contact the local after sales service authorized by Hikvision.-

Analog Camera

Analog Speed Dome

Monitor

Network Speed Dome

Monitor

NVR

DVR

TCP/IP

Network Camera

SYV

Product specificaties

Merk:	HiLook
Categorie:	Bewakingscamera
Model:	TK-4144TH-MH

Heb je hulp nodig?

Als je hulp nodig hebt met HiLook TK-4144TH-MH stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Bewakingscamera HiLook

HiLook TK-4144TH-MH Handleiding

11 Januari 2024

HiLook THC-T129-P Handleiding

18 December 2023

HiLook IPC-T651H-Z Handleiding

18 December 2023

HiLook IPC-T220 Handleiding

18 December 2023

HiLook THC-T140-P Handleiding

18 December 2023

HiLook IPC-D140H-M Handleiding

18 December 2023

HiLook IPC-B200 Handleiding

18 December 2023

HiLook IPC-D650H-V Handleiding

18 December 2023

HiLook IPC-B149H Handleiding

18 December 2023

HiLook IPC-T100-D Handleiding

18 December 2023

Handleiding Bewakingscamera

Nieuwste handleidingen voor Bewakingscamera

Aqara Camera Hub G2H Handleiding

28 April 2024

Iiquu Dummy Dome Camera Handleiding

28 April 2024

Sony SNC-VB640 Handleiding

26 April 2024

Sony SNC-EB642R Handleiding

26 April 2024

Sony SNC-VB642D Handleiding

26 April 2024

Sony SRG-HD1 Handleiding

26 April 2024

Sony SNC-ZM550 Handleiding

26 April 2024

Sony SNC-EM642R Handleiding

26 April 2024

Sony SNC-EM641 Handleiding

26 April 2024

Sony SNC-ZB550 Handleiding

26 April 2024