Hikvision DS-2CE56D5T-VFIR Handleiding

Hikvision Bewakingscamera DS-2CE56D5T-VFIR

Lees hieronder de 📖 handleiding in het Nederlandse voor Hikvision DS-2CE56D5T-VFIR (4 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 19 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

TURBO HD

1080P Dome Camera

User Manual

Regulatory Information

FCC Information

FCC compliance: This equipment has been

tested and found to comply with the limits for a

digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated in

a commercial environment. This equipment

generates, uses, and can radiate radio

frequency energy and, if not installed and used

in accordance with the instruction manual, may

cause harmful interference to radio

communications. Operation of this equipment in

a residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his own

expense.

FCC Conditions

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference.

2. This device must accept any interference

received, including interference that may

cause undesired operation.

EU Conformity Statement

upon the purchase of equivalent new equipment,

or dispose of it at designated collection points.

For more information see: www.recyclethis.info.

2006/66/EC (battery directive):

This product contains a battery that

cannot be disposed of as unsorted

municipal waste in the European

Union.

See the product documentation for specific

battery information. The battery is marked with

this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg).

UD.6L0201D1548A01

2012/19/EU (WEEE directive):

Products marked with this symbol

cannot be disposed of as unsorted

municipal waste in the European

Union. For proper recycling, return

this product to your local supplier

This product and - if applicable - the

supplied accessories too are marked

with "CE" and comply therefore with

the applicable harmonized European

standards listed under the Low Voltage Directive

2006/95/EC, the EMC Directive 2004/108/EC,

the RoHS Directive 2011/65/EU.

1.2 Overview

1.2.1 Overview of Type I Dome Camera

1.2.2 Overview of Type Dome Camera

1 Introduction

1.1 Product Features

This camera adopts new generation sensor with

high sensitivity and advanced circuit board design

technology. It possesses the features of high

resolution, low distortion, and low noise, etc. It is

extremely suitable for supervisory system and

image processing system.

The main features are as follows:

l High performance CMOS sensor and high

resolution bring high-quality image;

l Low illumination;

l Support IR cut filter with auto switch;

l OSD menu, parameters are configurable;

l Support auto white balance, auto gain control,

electronic shutter control and internal

synchronization;

l SMART IR mode;

l Unit transmission control;

l Advanced 3-axis design meets different

installation requirements.

l Please make sure that the device in the package

is in good condition and all the assembly parts

are included.

l Make sure that all the related equipment is

power-off during the installation.

l Check the specification of the products for the

installation environment.

l Check whether the power supply is matched

with your power output to avoid damage.

l Please make sure the wall is strong enough to

withstand three times the weight of the camera

and the mounting.

l If the wall is the cement wall, you need to insert

expansion screws before you install the camera.

If the wall is the wooden wall, you can use

self-tapping screw to secure the camera.

l If the product does not function properly,

please contact your dealer or the nearest

service center. Do not disassemble the camera

for repair or maintenance by yourself.

2.1 Ceiling Mounting

Steps:

1.Drill the screw holes and the cable hole on the

ceiling according to the supplied drill template.

Figure 2-1 The Drill Template

2 Loosen the screws on the bubble of type 1

camera /rotate the bubble of type2 camera to

remove the bubble and the black liner.

Figure 2-2 Remove the Bubble

For proper recycling, return the battery to your

supplier or to a designated collection point. For

more information see: www.recyclethis.info.

2 Installation

Before you start:

Thank you for purchasing our product. If there

are any questions, or requests, please do not

hesitate to contact the dealer.

This manual applies to DS-2CE56D5T-(A)VFIR and

DS-2CE56D5T-(A)VPIR3.

This manual may contain several technical

incorrect places or printing errors, and the

content is subject to change without notice.

The updates will be added to the new version of

this manual. We will readily improve or update

the products or procedures described in the

manual.

DISCLAIMER STATEMENT

Underwriters Laboratories Inc. (”UL” has not)

tested the performance or reliability of the

security or signaling aspects of this product.

UL has only tested for fire, shock or casualty

hazards as outlined in Ul’s Standard(s) for Safety,

UL60950-1. UL Certification does not cover the

performance or reliability of the security or

signaling aspects of this product. UL MAKES NO

REPRESENTATIONS, WARRANTIES OR

CERTIFICATIONS WHATSOEVER REGARDING

0100001040603

THE PERFORMANCE OR RELIABILITY OF ANY

SECURITY OR SIGNALING RELATED FUNCTIONS

OF THIS PRODUCT.

Figure 1-1 Overview of Type I Dome Camera

Figure 1-2 Overview of Type Dome CameraII

Type I: Type I :I

Type I :I

Type I:

Auxiliary Video Output

Black Liner

Bubble

Power Cable

HD Video Cable

CVBS Cable

Lens

Base plate

CVBS Cable

Back Box

Lens

Bubble

Black Liner

Power Cable

HD Video Cable

Auxiliary Video Output

Dip Switch

3 Menu Operation

Figure 3-1 Main Menu

SCENE LENS RESET

EXPOSURE WB DAY&NIGHT

BACKLIGHT NR SPECIAL ADJUST

INDOOR

OUTDOOR

INDOOR1

LOW-

LIGHT

MANUAL SHUT T ER

AGC

SENS-UP

BRIGHT NESS

D-WDR

DEFOG

BLC

HSBLC

ATW

AWC-SET

MANUAL

COLOR

B/W

EXT

2D NR

3D NR

CAM

TITLE

D-EFFECT

MOTION

PRIVACY

LAUGUAGE

DEFECT

VERSION

SHARPNESS

MONITOR

LSC

VIDEO.

OUT

EXIT

SETUP

3.1 VIDEO.OUT

PAL or NTSC is selectable .

3.2 LANGUAGE

English, Japanese, CHN1, CHN2, Korean, German,

French, Italian, Spanish, Polish, etc., are selectable.

3.3SETUP

3.3.1 SCENE

You can select indoor, outdoor, indoor 1 and low

-light as the working environments.

3.3.2 LENS

The camera is equipped with a fixed lens.

3.3.3 EXPOSURE

EXPOSURE

1. SHUTTER AUTO

2. AGC OFF

3. SENS-UP ---

4. BRIGHTNESS ---|------ 40

5. DEFOG OFF

6. D-WDR OFF

7. RETURN RET

Figure 3-2 Exposure

SHUTTER: AUTO,1/25, 1/50, FLK, 1/200, 1/400,

1/1k, 1/2k, 1/5k, 1/10k, 1/50k, x2, x4, x6, x8, x10,

and x15 are selectable.

: You can set the AGC value from 0 to 15.AGC

: You can set the SENS-UP to OFF or AUTO.SENS-UP

: You can set the brightness valueBRIGHTNESS

from 1 to 100.

: You can set the defog function as ON toDEFOG

enable the function. Position, size, and the defog

gradation are configurable.

You can set the D-WDR as ON or OFF.D-WDR:

3.3.4 Backlight

Backlight Compensation (BLC):

Set the gain of BLC as High, Middle, or Low.-GAIN:

Press the up/down/left/right button to-AREA:

define the BLC position and size. Select RET or

AGAIN to go back the BLC menu or re-define the

BLC area.

Restore the BLC settings to the default.-Default:

HSBLC: Select an HSBLC area. Set the DISPLAY

status as ON. Press the up/down/left/right button

to define the area position and size. Set the HSBLC

LEVEL from 0 to 100. Select ALL DAY or Night for the

HSBLC mode. Set the BLACK MASK status as ON or

OFF.

HSBLC

1. SELECT AREA 1

2. DISPLAY ON 8

3. LEVEL ---|------ 40

4. MODE ALL DAY

5. BLACK MASK ON

6. DEFAULT 8

7. RETURN RET

Figure 3-3 HSBLC

3.3.5 White Balance (WB)

MANUAL, ATW (Auto-tracking White Balance),

AWC→SET are selectable.

3.3.6 Day & Night

Color, B/W, and EXT are selectable for DAY and

NIGHT switches.

3.3.7 NR

: You can set 2D NR status as ON or OFF.2D NR

: Set the Smart NR status as ON and adjust3D NR

the 3D smart NR sensitivity ranges from 0 to 100.

Set the 3D NR LEVEL ranges from 0 to 100. Set the

2D&3D NR

1. 2DNR OFF

2. 3DNR ON 8

3. RETURN RET

3D NR

1. SMART NR ON8

2. LEVEL ------|--8 0

3. START. AGC -|--------10

4. END. AGC -|--------10

5. RETURN RET

Figure 3-4 NR

Figure 3-5 3D NR

3.3.8 SPECIAL

Edit the camera title on this section.Camera Title:

D-effect:

Set the freeze function as ON or OFF.-FREEZE:

OFF, MIRROR, V-FLIP, and ROTATE are-MIRROR:

selectable for mirror.

Define the zoom area by configuring-D-ZOOM:

the position from PAN & TILT.

The D-Zoom area, sensitivity-SMART D-ZOOM:

and time are configurable.

Set the NEG IMAGE as ON or OFF.-NEG.IMAGE:

SPECIAL

1. CAM TITLE ON 8

2. D-DFFECT 8

3. MOTION OFF

4. PRIVACY OFF

5. LANGUAGE ENG 8

6. DEFECT 8

7. RETURN RET

Figure 3-6 Special

MOTION

1. SELECT AREA 1

2. DISPLAY ON8

3. SENSITIVITY ----|---- 30

4. MOTION VIEW ON

5. DEFAULT 8

6. RETURN RET

Figure 3-7 Motion Detection

Motion: Select a MOTION area. Set the DISPLAY

status as ON or OFF. Press the up/down/left/right

button to define the position and size of the area.

Set the SENSITIVITY from 0 to 60. Set the MOTION

VIEW status as ON or OFF.

Privacy: Select a PRIVACY area. Set the DISPLAY

status as INV, MOSAIC, COLOR or OFF. Press the

up/down/left/right button to define the position

and size of the area.

Defect: LIVE DPC, STATIC DPC and Black DPC are

adjustable in this section.

PRIVACY

1. SELECT AREA 1

2. DISPLAY MOSAIC 8

3. COLOR 10

4. TRANS. 1

5. DEFAULT 8

6. RETURN RET

ADJUST

1. SHARPNESS --------|15

2. MONITOR LCD8

3. LSC OFF

4. RETURN RET

3.3.9 ADJUST

: Adjust the sharpness from 0 to 15.Sharpness

: Monitor CRT, and Monitor LCD areMonitor

selectable.

: Set the LSC status as ON or OFF.LSC

3.3.10 RESET

Reset all the settings to the default.

3.3.11 EXIT

Press OK to exit the menu.

START. AGC level as the threshold to enable AGC,

and set the END. AGC level as the threshold to

disable AGC.

Figure 3-8 Privacy Mask Figure 3-9 Adjust

Steps:

1.Drill the screw holes and the cable hole in the

ceiling according to the supplied drill template.

2.Screw the bolts through the mount by aligning

with the 2 bolt holes. Fit the toggles onto the bolts.

3.Push the two toggle bolts through the two screw

holes on the ceiling. Rotate the bolt till the toggle

holds the ceiling tightly.

2.2 In-ceiling Mounting

Figure 2-5 Install the Mount

Figure 2-6 Fix the Camera to the Mount

Figure 2-8 Fix the Camera to the Gang Box

6. Repeat steps 6-8 of the Ceiling Mounting section

to complete the installation.

4.Route and connect the corresponding cables.

5.Fix the camera to the in-ceiling mount with the

supplied screws.

3.Attach the back box of type 1 camera /base plate

of type2 camera to the ceiling and secure them

with supplied self-tapping screws.

4.Route the cables through the cable hole.

5.Align the camera with the back box/base plate,

and tighten the set screws to secure the camera

with the back box/base plate.

Figure 2-3 Fix the Camera to the Ceiling

6. Connect the corresponding cables.

7. Adjust the camera according to the figure below

to get an optimum angle.

8. Fit the black liner on the camera and tighten the

screws on the bubble of type 1 camera or rotate the

bubble of type 2 camera to complete.

Figure 2-4 Zoom and Focus Adjustment

You need to purchase an in-ceiling mount separately

if you adopt in-celling mounting.

2.3 In-ceiling Mounting with

Gang Box

Only the type 1 camera supports in-ceiling

mounting with gang box.

1.Repeat steps 2-3 of the In-ceiling Mounting

section to secure the in-ceiling mount (supplied)

to the gang box.

Figure 2-7 Install the Mount

2.Route and connect the corresponding cables.

3.Align the camera with the gang box, and tighten

the screws to secure the camera with the gang box..

4. Repeat steps 6-8 of the Ceiling Mounting section

to complete the installation.

Type I: Type I :IType I :IType I :I

0 ~90° °

0 ~355° °

PP Direction

Direction

DirectionDirection

RR Direction

Direction

DirectionDirection

TT Direction

Direction

DirectionDirection

Type I:

0°~355°

0 ~90° °

0 ~340° °

TT Direction

Direction

DirectionDirection

RR Direction

Direction

DirectionDirection

PP Direction

Direction

DirectionDirection

Type I :I

Type I: Type I :I

You can call the menu and adjust the camera

parameters with a coaxial camera controller

(purchase separately). You can also call the menu

with supported TVI DVR.

Product specificaties

Merk:	Hikvision
Categorie:	Bewakingscamera
Model:	DS-2CE56D5T-VFIR
Kleur van het product:	Black, White
Gewicht:	600 g
Hoogte:	101 mm
Soort:	CCTV-bewakingscamera
Bluetooth:	Nee
Vormfactor:	Dome
Ondersteuning voor plaatsing:	Binnen
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Nee
Montagewijze:	Plafond/muur
Ondersteunde video-modi:	1080p
Maximum resolutie:	- Pixels
Totaal aantal megapixels:	2 MP
Diameter:	136 mm
Type stroombron:	DC
Stroomuitvoer (volt):	12
Minimale belichting:	0 Lux
Field of view (FOV) hoek:	103 °
Aantal cameras:	1
Ingebouwde HDD:	Nee
Nachtvisie:	Ja
LED-type:	IR
Video bewegings-detectie:	Ja
Brandpuntbereik:	- mm
Vermogensverbruik (max):	4 W
Formaat analoog signaal:	NTSC, PAL
Omvang optische sensor:	- "
Type beeldsensor:	CMOS
Camera sluitertijd:	1/25(1/30) - 1/50000 s
Witbalans:	ATW, AWC, Indoor, Outdoor
Maximaal 30 frames per seconde:	30 fps
Composiet video-uitgang:	1
Signaal/ruis-verhouding:	62 dB
Ondersteunde talen:	ARA, CHI (SIMPL), CHI (TR), DEU, DUT, ENG, ESP, FRE, HEB, ITA, JPN, KOR, POL, POR, RUS, TUR
Type sterkteregeling:	Auto
Draaihoek:	355 °
Pan bereik:	0 - 355 °
Dag/nacht modus:	Ja
Aantal lenzen:	1
Maximum aperture number:	1.4
Controle camerapanning:	Ja
Kantelfunctie camera:	Ja
Aantal sensoren:	1
Nachtkijker afstand:	30 m
Infrarood (IR)-afsluitingsfilter:	Ja
Achtergrondverlichting compensatie:	Ja
Aantal talen:	16
Wide Dynamic Range (WDR):	Ja
Wifi:	Nee
AC-ingangsspanning:	24 V
Bedrijfstemperatuur (T-T):	-20 - 45 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Bereik kantelhoek:	0 - 75 °
Privézone maskeren:	Ja
Anti-flikkering:	Ja