Hikvision DS-2CE56D1T-VFIR3 Handleiding

Hikvision Bewakingscamera DS-2CE56D1T-VFIR3

Lees hieronder de 📖 handleiding in het Nederlandse voor Hikvision DS-2CE56D1T-VFIR3 (4 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 21 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

TVI Turret & Bullet Camera

User Manual

Regulatory Information

FCC Information

FCC compliance: This equipment has been

tested and found to comply with the limits for a

digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated in

a commercial environment. This equipment

generates, uses, and can radiate radio

frequency energy and, if not installed and used

in accordance with the instruction manual, may

cause harmful interference to radio

communications. Operation of this equipment in

a residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his own

expense.

FCC Conditions

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference.

2. This device must accept any interference

received, including interference that may

cause undesired operation.

EU Conformity Statement

upon the purchase of equivalent new equipment,

or dispose of it at designated collection points.

For more information see: www.recyclethis.info.

2006/66/EC (battery directive):

This product contains a battery that

cannot be disposed of as unsorted

municipal waste in the European

Union.

See the product documentation for specific

battery information. The battery is marked with

this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg).

For proper recycling, return the battery to your

supplier or to a designated collection point. For

more information see: www.recyclethis.info.

UD.6L0201D1937A01

2012/19/EU (WEEE directive):

Products marked with this symbol

cannot be disposed of as unsorted

municipal waste in the European

Union. For proper recycling, return

this product to your local supplier

This product and - if applicable - the

supplied accessories too are marked

with "CE" and comply therefore with

the applicable harmonized European

standards listed under the Low Voltage Directive

2006/95/EC, the EMC Directive 2004/108/EC,

the RoHS Directive 2011/65/EU.

TURBO HD

This series of camera adopts new generation

sensor with high sensitivity and advanced circuit

design technology It features high resolution,.

low image distortion and low noise, etc , which.

makes it suitable for surveillance system and

image processing system.

l High performance CMOS sensor and high

resolution bring high-quality image;

l Low illumination;

l OSD menu, parameters are configurable;

Support auto white balance, auto gain control,

electronic shutter control;

Support image effect adjustment;

Unit transmission control;

l Advanced 3-axis design meets different

installation requirements.

1 Introduction

1.1 Product Features

2 Installation

l Check the specification of the products for the

installation environment.

l Check whether the power supply is matched

with your power output to avoid damage.

l Please make sure the wall is strong enough to

withstand three times the weight of the camera

and the mounting.

l If the wall is the cement wall, you need to insert

expansion screws before you install the camera.

If the wall is the wooden wall, you can use

self-tapping screw to secure the camera.

l If the product does not function properly,

please contact your dealer or the nearest

service center. Do not disassemble the camera

for repair or maintenance by yourself.

1.2 Overview

1.2.1 Overview of Type I Camera

1.2.2 Overview of Type Camera

Figure 1-1 Overview of Type I Camera

Figure 1-2 Overview of Type CameraII

2.1 Installation of Type CameraI

Steps:

1.Drill the screw holes and the cable hole on the

ceiling according to the supplied drill template.

Figure 2-1 The Drill Template

2 Push the lock button to disassemble the camera

from the mounting base.

Figure 2-2 Release The Lock Screw

l Please make sure that the device in the package

is in good condition and all the assembly parts

are included.

l Make sure that all the related equipment is

power-off during the installation.

3.Fix the mounting base to the ceiling.

Before you start:

Cameras in some models do not support OSD

menu. For actual operation, please refer to the

specification of each model.

4.Route the cables to the cable hole and connect

the corresponding cables.

5.Secure the camera to the mounting base by

supplied screws. Keep the word UP on the camera

being upright during the installation to make the

image showing normally.

Thank you for purchasing our product. If there

are any questions, or requests, please do not

hesitate to contact the dealer.

This manual applies to

This manual may contain several technical

incorrect places or printing errors, and the

content is subject to change without notice.

The updates will be added to the new version of

this manual. We will readily improve or update

the products or procedures described in the

manual.

0100001050330

Please refer to the product specification for

camera parameters and functions.

Type

Model

Privacy Notice

Surveillance laws vary by jurisdiction. Check

all relevant laws in your jurisdiction before using

this product for surveillance purposes to ensure

that your use of this product conforms.

DS-2CE56D1T-VFIR3

DS-2CE56D1T-AVFIR3

DS-2CE16D1T-VFIR3

Figure 2-4 Universal Adjustment

6.Adjust the camera according to the figure below

to get an optimum angle.

Figure 2-3 Secure the Camera

7.Use the screwdriver to adjust the ZOOM screw

and the FOCUS screw until you get the optimum

image.

Figure 2-5 Zoom and Focus Adjustment

2.2 Installation of Type II Camera

Both wall mounting and ceiling mounting are

suitable for type bullet camera. Ceiling mountingII

will be taken as an example in the section. And you

can take steps of ceiling mounting as a reference

if wall mounting is adopted.

Steps:

1.Drill the screw holes and the cable hole in the

ceiling according to the supplied drill template.

2.Hammer the supplied plastic expansion bolt into

the screw holes.

Figure 2-6 Drill Template

3.Route the cables to the cable hole and connect

the corresponding cables.

4.Fix the camera to the ceiling with the supplied

screws.

Figure 2-7 Fix the Camera to the Ceiling

Figure 2-8 3-axis Adjustment

5. Adjust the surveillance angle.

1). Loosen No.1 adjusting screw to adjust the pan

position (0 ~ 360 ).° °

2).Tighten No.1 adjusting screw.

3). Loosen No.2 adjusting screw to adjust the

tilting position(0 ~ 90 ).° °

4).Tighten No.2 adjusting screw.

5). Loosen No.3 adjusting screw to adjust the

rotation position 0 ~ 360 .( ° ° )

6).Tighten No.3 adjusting screw.

0~360

0~90

3.2.2 WB

3.2.1 AE

Move the cursor to AE, and you can adjust the

image brightness by the ,BRIG HTN ESS EXPOSURE

MODE AG C, and .

:Brightness

Brightness refers to the brightness of the image.

Exposure Mode:

Move the cursor to , you can selectExposure Mode

the exposure mode between and .Globe BLC

When BLC is selected as the exposure mode, the

level of B LC mode can be adjusted, as shown in the

Figure 3-2.

3.2.4 VIDEO SET T ING

Contrast:

Contrast enhances the difference in color and light

between parts of an image.

You can set the value from 1 to .

Sharpness:

Sharpness determines the amount of

detail that an imaging system can reproduce.

You can set the value from 1 to 10.

Saturation:

You can set the saturation level of the image. The

value is from 0 to 10.

DNR:

DNR decreases the noise effect, especially in low

light conditions and delivers more accurate and

sharp image quality. You can set the value from

0 to 7.

:Mirror

You can set the Mirror status as H, V, HV, or O FF.

3 Menu Operation

Figure 3-1 Main Menu

VIDEO

SETTING

DAY/NIGHTWB RESET

BRIGHTNESS MODE

INFRARED

SMART IR

CONTRAST

SHARPNESS

SATURATION

EXITAE

DNR

MIRROR

EXPOSURE MODE

AGC

SAVE/EXIT

With a coaxial camera controller (purchase

separately) or calling the preset No.95 you can

select the menu and adjust the camera parameters.

3.1 FORMAT

You can set the format as PAL/NTSC.

6.Push the focus &zoom adjustment cover upward

to move it aside.

7.Use the cover as a screwdriver to adjust the ZOOM

screw and the FOCUS screw until you get the

optimum image.

Cover

CoverCover

Focu

FocuFocus

Zoom

ZoomZoom

0~360

Cover

CoverCover

Figure 2-9 Zoom and Focus Adjustment

3.2 SET UP

Move the cursor to , and press menu buttonSET UP

to enter the SET UP sub menu.

EXPOSURE

1.BRIGHTNESS

2.EXPOSURE MODE

LEVEL

3.AGC

4.RETURN

BLC

MIDDLE

Move the cursor to WB, and you can set White

Balance mode as and in this menuAWB MWB .

AWB: white balance is being adjusted

automatically.

: Set the value from 1 to 10.MWB R GAIN/B GAIN

As shown in Figure 3-3.

MODE MWB

R GIAN 1-|--10

B GAIN 1-|--10

RETURN 8

AGC:

AGC optimizes the clarity of image in poor light

scene. AGC level can be set as OFF, LOW, MIDDLE

and HIGH.

Fi gure 3-2 EXPOSU RE

Figure 3-3 WB

Figure 3-4 DAY/NIGHT

3.2.3 DAY & NIGHT

Move the cursor to DAY & NIGHT, and select

COLOR B/W SMART, , or as the DAY & NIGHT mode.

COLOR: The image is colored in day mode all the

time.

: The image is black & white all the time, andB/W

the IR LED turns on in the low-light conditions.

: Select to turn on/off the INFRARED_LAMPSMART

and to set the Smart IR level from 1to 16.

As shown in Figure 3-4.

DAY/NIGHT

MODE SMART

INFRARED OFF

SMART IR 0-|--5

RETURN 8

3.2.7 SAVE/EXIT

3.2.5 Reset

Reset all the settings to the default.

3.2.6 EXIT

Exit and Save & exit are selectable.

Move the cursor to , and press OK toSAVE & Exit

save the settings and exit the menu.

Product specificaties

Merk:	Hikvision
Categorie:	Bewakingscamera
Model:	DS-2CE56D1T-VFIR3
Kleur van het product:	Wit
Gewicht:	600 g
Breedte:	130.54 mm
Diepte:	102.4 mm
Soort:	IP-beveiligingscamera
Internationale veiligheidscode (IP):	IP66
Bluetooth:	Nee
Vormfactor:	Dome
Ondersteuning voor plaatsing:	Buiten
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Nee
Montagewijze:	Plafond
Ondersteunde video-modi:	1080p
Maximum resolutie:	1930 x 1088 Pixels
Totaal aantal megapixels:	2 MP
Diameter:	112.4 mm
Type stroombron:	AC
Stroomuitvoer (volt):	12
Minimale belichting:	0.01 Lux
Field of view (FOV) hoek:	114.5 °
Aantal cameras:	1
Ingebouwde HDD:	Nee
Nachtvisie:	Ja
LED-type:	IR
Brandpuntbereik:	- mm
Vermogensverbruik (max):	4.5 W
Formaat analoog signaal:	NTSC, PAL
Type beeldsensor:	CMOS
Camera sluitertijd:	1/25 - 1/50000 s
Witbalans:	Auto
Ondersteunde grafische resoluties:	1920 x 1080 (HD 1080)
Signaal/ruis-verhouding:	62 dB
Ondersteunde talen:	CHI (SIMPL), ENG
Power over Ethernet (PoE):	Nee
Draaihoek:	360 °
Pan bereik:	0 - 360 °
Dag/nacht modus:	Ja
Maximum aperture number:	1.4
Weerbestendig:	Ja
Nachtkijker afstand:	20 m
Aantal talen:	2
Wifi:	Nee
Bedrijfstemperatuur (T-T):	-40 - 60 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Bereik kantelhoek:	0 - 75 °
Draaien & spiegelen:	Ja
Lens mount interface:	M12