Hikvision DS-2CE56D1T-IR3Z Handleiding

Hikvision Bewakingscamera DS-2CE56D1T-IR3Z

Lees hieronder de 📖 handleiding in het Nederlandse voor Hikvision DS-2CE56D1T-IR3Z (3 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3

TURBO HD

1080P Turret &Bullet Camera

User Manual

Regulatory Information

FCC Information

FCC compliance: This equipment has been

tested and found to comply with the limits for a

digital device, pursuant to part 15 of the FC C

Rules. These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated in

a commercial environment. This equipment

generates, uses, and can radiate radio

frequency energy and, if not installed and used

in accordance with the instruction manual, may

cause harmful interference to radio

communications. Operation of this equipment in

a residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his own

expense.

FCC Conditions

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference.

2. This device must accept any interference

received, including interference that may

cause undesired operation.

EU Conformity Statement

upon the purchase of equivalent new equipment,

or dispose of it at designated collection points.

For more information see: www.recyclethis.info.

2006/66/EC (battery directive):

This product contains a battery that

cannot be disposed of as unsorted

municipal waste in the European

Union.

See the product documentation for specific

battery information. The battery is marked with

this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg).

U D.6L0201D1999A02

2012/19/EU (WEEE directive):

Products marked with this symbol

cannot be disposed of as unsorted

municipal waste in the European

Union. For proper recycling, return

this product to your local supplier

This product and - if applicable - the

supplied accessories too are marked

with "C E" and comply therefore with

the applicable harmonized European

standards listed under the Low Voltage Directive

2006/95/EC, the EMC Directive 2004/108/EC,

the RoHS Directive 2011/65/EU.

1.2 Overview

1.2.1 Overview of Type I Camera

1.2.2 Overview of Type Camera

HD Video Cable

Enclosure

Lock Button

Mounting Base

Camera

Power Cable

1 Introduction

1.1 Product Features

This camera adopts new generation sensor with

high sensitivity and advanced circuit board design

technology. It possesses the features of high

resolution, low distortion, and low noise, etc. It is

extremely suitable for supervisory system and

image processing system.

The main features are as follows:

l High performance CMOS sensor and high

resolution bring high-quality image;

l Low illumination;

l Support IR cut filter with auto switch;

l OSD menu, parameters are configurable;

l Support auto white balance, auto gain control,

electronic shutter control and internal

synchronization;

l SMART IR mode;

l 2.8-12mm motorized vari-focal lens;

l Advanced 3-axis design meets different

installation requirements.

l Please make sure that the device in the package

is in good condition and all the assembly parts

are included.

l Make sure that all the related equipment is

power-off during the installation.

l Check the specification of the products for the

installation environment.

l Check whether the power supply is matched

with your power output to avoid damage.

l Please make sure the wall is strong enough to

withstand three times the weight of the camera

and the mounting.

l If the wall is the cement wall, you need to insert

expansion screws before you install the camera.

If the wall is the wooden wall, you can use

self-tapping screw to secure the camera.

l If the product does not function properly,

please contact your dealer or the nearest

service center. Do not disassemble the camera

for repair or maintenance by yourself.

2.1 Installation of Type CameraI

Steps:

1.Drill the screw holes and the cable hole on the

ceiling according to the supplied drill template.

Figure 2-1 The Drill Template

2 Loosen the screws to remove the clip plate and

take out the main body.

3.Fix the mounting base to the ceiling with PA4*25

screws.

Figure 2-2 Remove the Clip Plate

For proper recycling, return the battery to your

supplier or to a designated collection point. For

more information see: www.recyclethis.info.

2 Installation

Before you start:

Thank you for purchasing our product. If there

are any questions, or requests, please do not

hesitate to contact the dealer.

This manual may contain several technical

incorrect places or printing errors, and the

content is subject to change without notice.

The updates will be added to the new version of

this manual. We will readily improve or update

the products or procedures described in the

manual.

0100001050522

Figure 1-1 Overview of Type I Camera

Figure 1-2 Overview of Type CameraII

Privacy Notice

Surveillance laws vary by jurisdiction. Check all

relevant laws in your jurisdiction before using

this product for surveillance purposes to ensure

that your use of this product conforms.

Please refer to the product specification for

camera parameters and functions.

OSD Button

Power Cable

Lens

Main Body

Mounting Base

HD Video Cable

Industry Canada IC ES-003 Compliance

This device meets the CAN ICES-3 (A)/NMB-3(A)

standards requirements.

Screw Hole

120°

Steps:

1.Drill the screw holes and the cable hole in the

ceiling according to the supplied drill template.

2.Hammer the supplied plastic expansion bolt into

the screw holes.

2.2 Installation of Type II Camera

Figure 2-5 Drill Template

3.Route the cables to the cable hole and connect

the corresponding cables.

4.Fix the camera to the ceiling with the supplied

screws.

4.Route the cables to the cable hole and connect

the corresponding cables.

5.Install the main body onto the mounting plate

and insert the clip plate.

6.Tighten the screws with the wrench.

Figure 2-4 3-axis Adjustment

0 ~360°

0 ~75°

0~360°

Both wall mounting and ceiling mounting are

suitable for type bullet camera. Ceiling mounting

will be taken as an example in the section. And you

can take steps of ceiling mounting as a reference

if wall mounting is adopted.

360°

90°

360°

Figure 2-6 Fix the Camera to the Ceiling

5. Adjust the surveillance angle.

1). Loosen No.1 adjusting screw to adjust the pan

position (0 ~ 360 ).° °

2).Tighten No.1 adjusting screw.

3). Loosen No.2 adjusting screw to adjust the

tilting position(0 ~ 90 ).° °

4).Tighten No.2 adjusting screw.

5). Loosen No.3 adjusting screw to adjust the

rotation position 0 ~ 360 .( ° ° )

6).Tighten No.3 adjusting screw.

Figure 2-7 3-axis Adjustment

3.3 DAY/NIGHT

Color, B/W, AUTO and EX T are selectable for DAY/

NI GHT switches. Under the mode of the AUTO and

EXT, you can set the IR LED as Smart and CDS. If the

IR LE D is selected as Smart, you can set the bright-

ness of the I R LED.

3.4 AWB

Figure 3-2 DAY/NIGHT

Figure 3-3 AWB

SPECIAL

1. PRIVACY ZONE

2. MOTION

3. HLC

4. RETURN RET

Figure 3-4 SPECIAL

Motion: Set the Motion status as ON or OFF. Set

the SENSITIVITY from 0 to 255. Set the alarm status

as ICON/TRANCE/OFF. Set the hold time from

0 second to 255 seconds.

HLC: HLC supplements the brightness of the

peripheral area of the image. You can set the mask

value and threshold from 0 to 255.

Privacy zone: Select a PRIVACY area. Set the

MASK PAT as OFF, GRAY, WHIT E or BLACK. Set the

SX/EX/SY/EY value to define the position and size

of the area.

DAY/NIGHT

1. MODE AUTO

2. D TO N 63

3. N TO D 63

4. DELAY TIME 20

5. RETURN RET

AWB

1. MODE AUTO

2. R-G GAIN 255

3. B-G GAIN 151

4. RETURN RET

Auto, User, Push, 8000k, 6000k, 4200k and 3000k

are selectable for AW B. Under the mode of AUTO,

you need to set the R-G/B-G Gain and to select an

indoor/outdoor mode. If the AWB mode is select

as User, You need to set the R/G/B Gain manually.

3.5 AE

You can set the AE mode as HOLD, DC and ESC.

: Brightness refers to the brightnessBrightness

of the image.

: Shutter denotes the speed of the shutter.Shutter

You can set the shutter as AUTO, 1/25, 1/30, 1/50,

1/60, 1/100, 1/120, 1/250, 1/500, 1/1k, 1/3k and

1/10k.

: You can set the flicker status as 50HZ/60HZFlicker

to prevent image flicking.

: BLC bases on the back area to enhance theBLC

brightness of the whole image. You can set the

BLC gain from 0 to 16.

: AGC optimizes the clarity of image in poorAGC

light scene. The value of AGC can be set from 1-5.

: LSC corrects the phenomenon where theLSC

image gets darkened or blurred on the periphery.

3.6 SPECIAL

SYSTEM

1. CAMERA ID 255

2. ID DISP. ON

3. NAME DISP. ON

4. LANGUAGE ENG

5. FACTORY INIT OFF

6. RETURN RET

3.8 SYSTEM

You can set the camera ID from 0 to 255.

Select the ID display and name display status as

ON/OFF.

Chinese and English are selectable for the language

of the menu.

You can restore the camera to the default by

setting the factory initialization status as ON.

3.9 EXIT

Exit and Save & exit are selectable.

EFFECT

1. COLOR GAIN 200

2. COLOR HUE 200

3. SHARPNESS 25

4. CONTRAST 150

5. BRIGHT OFF. 1

6. MIRROR ON

7. FLIP ON

8. RETURN RET

Color Gain: Color gain adjust this feature to change

the saturation of the color. You can set the value

from 0 to 255.

: You can adjust the image HUE fromColor Hue

0 to 71.

: Sharpness determines the amount ofSharpness

detail that an imaging system can reproduce.

You can set the value from 0 to 255.

: Contrast enhances the difference inContrast

color and light between parts of an image.

You can set the value from 0 to 255.

: Bright Off. refers to the brightnessBright Off.

compensation of the image. You can set the bright

compensation value as 0 or 1.

: You can set the Mirror status as ON/OFF.Mirror

: You can set the F LIP status as ON/OFF.Flip

3.7 EFFECT

Figure 3-5 EFFEC T Figure 3-6 SYST EM

Figure 3-1 Main Menu

AWB

DAY&NIGHT SYSTEM

SPECIAL EFFECT

ESC

HOLD

FRAME

RATE

AUTO

USER

HOLD

8000K

6000K

COLOR

B/W

AUTO

CAMERA

ID DISP

PRIVACY

ZONE

MOTION

HLC

LANGUAGE

COLOR

GAIN

COLOR

HUE

SHARPNESS

EXIT

VIDEO. OUT

4200K

3200K

CONTRAST

BRIGHT

MIRROR

FLIP

NAME

DISP

FACTORY

INIT

EXT

PUSH

A coaxial camera controller (purchase separately)

is required to select the menu and adjust the

camera parameters.

3.2 VIDEO.OUT

You can set the frame rate as 25 fps/30fps.

3 Menu Operation

3.1 Smart Focus

Press the menu button to enter the menu interface.

When the menu interface is not displayed, you can

press and hold any direction key of the joystick

for 3s to enter the focusing interface. Move the

joystick to adjust the camera lens by the FOCUS+,

FOC US-, ZOOM+ a nd ZOOM-.

After connecting the camera with back-end device,

you can also control the camera with mouse in PTZ

control mode. The direction keys works as the menu

joystick.

7.Adjust the camera according to the figure below

to get an optimum angle.

Figure 2-3 Install the Turret Camera

Product specificaties

Merk:	Hikvision
Categorie:	Bewakingscamera
Model:	DS-2CE56D1T-IR3Z
Kleur van het product:	Wit
Gewicht:	710 g
Breedte:	130.54 mm
Diepte:	130.54 mm
Hoogte:	102.4 mm
Soort:	CCTV-bewakingscamera
Internationale veiligheidscode (IP):	IP66
Bluetooth:	Nee
Vormfactor:	Dome
Ondersteuning voor plaatsing:	Buiten
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Nee
Montagewijze:	Plafond
Ondersteunde video-modi:	1080p
Maximum resolutie:	1930 x 1088 Pixels
Totaal aantal megapixels:	2 MP
Diameter:	130.54 mm
Type stroombron:	DC
Stroomuitvoer (volt):	12
Minimale belichting:	0.01 Lux
Aantal cameras:	1
Ingebouwde HDD:	Nee
Nachtvisie:	Ja
LED-type:	IR
Video bewegings-detectie:	Ja
Focus:	Gemotoriseerd
Brandpuntbereik:	2.8 - 12 mm
Vermogensverbruik (max):	5 W
Formaat analoog signaal:	NTSC,PAL
Volledige HD:	Ja
Type beeldsensor:	CMOS
Camera sluitertijd:	1/25 - 1/50000 s
Witbalans:	Auto,Push
Ondersteunde grafische resoluties:	1920 x 1080 (HD 1080)
Ruisonderdrukking:	Ja
Lengte:	102.4 mm
Maximaal 30 frames per seconde:	30 fps
Geschikt voor buitengebruik:	Ja
Signaal/ruis-verhouding:	62 dB
Ondersteunde talen:	CHI (TR),ENG
Power over Ethernet (PoE):	Nee
Draaihoek:	360 °
Pan bereik:	0 - 360 °
Dag/nacht modus:	Ja
Maximum aperture number:	1.4
Minimum aperture number:	1.2
Weerbestendig:	Ja
Nachtkijker afstand:	40 m
Infrarood (IR)-afsluitingsfilter:	Ja
Achtergrondverlichting compensatie:	Ja
Op afstand bekijken:	Ja
Aantal talen:	2
Wifi:	Nee
Bedrijfstemperatuur (T-T):	-40 - 60 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Bereik kantelhoek:	0 - 75 °
Privézone maskeren:	Ja
Spiegel:	Ja
Anti-flikkering:	Ja
Smart IR:	Ja