Hikvision DS-2CE56D1T-AVPIR3(2.8-12MM) Handleiding

Hikvision Bewakingscamera DS-2CE56D1T-AVPIR3(2.8-12MM)

Lees hieronder de 📖 handleiding in het Nederlandse voor Hikvision DS-2CE56D1T-AVPIR3(2.8-12MM) (4 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

TURBO HD

1080P Dome Camera

User Manual

UD.6L0201D1939A01

1.2 Overview

1.2.1 Overview of Type I Dome Camera

1.2.2 Overview of Type Dome Camera

1 Introduction

1.1 Product Features

This camera adopts new generation sensor with

high sensitivity and advanced circuit board design

technology. It possesses the features of high

resolution, low distortion, and low noise, etc. It is

extremely suitable for supervisory system and

image processing system.

The main features are as follows:

l High performance CMOS sensor and high

resolution bring high-quality image;

l Low illumination;

l Support IR cut filter with auto switch;

l OSD menu, parameters are configurable;

l Support auto white balance, auto gain control,

electronic shutter control and internal

synchronization;

l SMART IR mode;

l Unit transmission control;

l Advanced 3-axis design meets different

installation requirements.

l Please make sure that the device in the package

is in good condition and all the assembly parts

are included.

l Make sure that all the related equipment is

power-off during the installation.

l Check the specification of the products for the

installation environment.

l Check whether the power supply is matched

with your power output to avoid damage.

l Please make sure the wall is strong enough to

withstand three times the weight of the camera

and the mounting.

l If the wall is the cement wall, you need to insert

expansion screws before you install the camera.

If the wall is the wooden wall, you can use

self-tapping screw to secure the camera.

l If the product does not function properly,

please contact your dealer or the nearest

service center. Do not disassemble the camera

for repair or maintenance by yourself.

2.1 Ceiling Mounting

Steps:

1.Drill the screw holes and the cable hole on the

ceiling according to the supplied drill template.

Figure 2-1 The Drill Template

2 Loosen the screws on the bubble of type 1

camera /rotate the bubble of type2 camera to

remove the bubble and the black liner.

Figure 2-2 Remove the Bubble

2 Installation

Before you start:

Figure 1-1 Overview of Type I Dome Camera

Figure 1-2 Overview of Type Dome CameraII

Type I: Type I :I

Black Liner

Bubble

Power Cable

HD Video Cable

Lens

Base plate

Back Box

Lens

Bubble

Black Liner

Power Cable

HD Video Cable

Type I :IType I:

Regulatory Information

FCC Information

FCC compliance: This equipment has been

tested and found to comply with the limits for a

digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated in

a commercial environment. This equipment

generates, uses, and can radiate radio

frequency energy and, if not installed and used

in accordance with the instruction manual, may

cause harmful interference to radio

communications. Operation of this equipment in

a residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his own

expense.

FCC Conditions

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference.

2. This device must accept any interference

received, including interference that may

cause undesired operation.

EU Conformity Statement

upon the purchase of equivalent new equipment,

or dispose of it at designated collection points.

For more information see: www.recyclethis.info.

2006/66/EC (battery directive):

This product contains a battery that

cannot be disposed of as unsorted

municipal waste in the European

Union.

See the product documentation for specific

battery information. The battery is marked with

this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg).

For proper recycling, return the battery to your

supplier or to a designated collection point. For

more information see: www.recyclethis.info.

2012/19/EU (WEEE directive):

Products marked with this symbol

cannot be disposed of as unsorted

municipal waste in the European

Union. For proper recycling, return

this product to your local supplier

This product and - if applicable - the

supplied accessories too are marked

with "CE" and comply therefore with

the applicable harmonized European

standards listed under the Low Voltage Directive

2006/95/EC, the EMC Directive 2004/108/EC,

the RoHS Directive 2011/65/EU.

Thank you for purchasing our product. If there

are any questions, or requests, please do not

hesitate to contact the dealer.

This manual applies to

This manual may contain several technical

incorrect places or printing errors, and the

content is subject to change without notice.

The updates will be added to the new version of

this manual. We will readily improve or update

the products or procedures described in the

manual.

0100001050409

Please refer to the product specification for

camera parameters and functions.

Type

Model

Privacy Notice

Surveillance laws vary by jurisdiction. Check

all relevant laws in your jurisdiction before using

this product for surveillance purposes to ensure

that your use of this product conforms.

DS-2CE56D1T-AVPIR3/ VPIR3

DS-2CE56D1T-AVFIR/VFIR

Steps:

1.Drill the screw holes and the cable hole in the

ceiling according to the supplied drill template.

2.Screw the bolts through the mount by aligning

with the 2 bolt holes. Fit the toggles onto the bolts.

3.Push the two toggle bolts through the two screw

holes on the ceiling. Rotate the bolt till the toggle

holds the ceiling tightly.

2.2 In-ceiling Mounting

Figure 2-5 Install the Mount

Figure 2-6 Fix the Camera to the Mount

Figure 2-8 Fix the Camera to the Gang Box

6. Repeat steps 6-8 of the Ceiling Mounting section

to complete the installation.

4.Route and connect the corresponding cables.

5.Fix the camera to the in-ceiling mount with the

supplied screws.

3.Attach the back box of type 1 camera /base plate

of type2 camera to the ceiling and secure them

with supplied self-tapping screws.

4.Route the cables through the cable hole.

5.Align the camera with the back box/base plate,

and tighten the set screws to secure the camera

with the back box/base plate.

Figure 2-3 Fix the Camera to the Ceiling

6. Connect the corresponding cables.

7. Adjust the camera according to the figure below

to get an optimum angle.

8. Fit the black liner on the camera and tighten the

screws on the bubble of type 1 camera or rotate the

bubble of type 2 camera to complete.

Figure 2-4 3-axis Adjustment

You need to purchase an in-ceiling mount separately

if you adopt in-celling mounting.

2.3 In-ceiling Mounting

in-ceiling mounting with gang box is supported by

the both types of camera.

1.Repeat steps 2-3 of the In-ceiling Mounting

section to secure the in-ceiling mount (supplied)

to the gang box.

Figure 2-7 Install the Mount

2.Route and connect the corresponding cables.

3.Align the camera with the gang box, and tighten

the screws to secure the camera with the gang box..

5. Repeat steps 6-8 of the Ceiling Mounting section

to complete the installation.

Type I: Type I :I

0 ~75° °

0 ~355° °

PP Direction

Direction

DirectionDirection

RR Direction

Direction

DirectionDirection

TT Direction

Direction

DirectionDirection

Type I:

0°~355°

0 ~75° °

0 ~340° °

TT Direction

Direction

DirectionDirection

RR Direction

Direction

DirectionDirection

PP Direction

Direction

DirectionDirection

Type I :I

Type I: Type I :IType I :IType I :I

3.2.2 W B

3.2.1 AE

Move the cursor to AE, and you can adjust the

image brightness by the ,BRIGHT NESS EXPOSURE

MODE AGC, and .

:Brightness

Brightness refers to the brightness of the image.

Exposure Mode:

Move the cursor to , you can selectExposure Mode

the exposure mode between and .Globe BLC

When BLC is selected as the exposure mode, the

level of BLC mode can be adjusted, as shown in the

Figure 3-2.

3.2.4 VIDEO SETTING

Contrast:

Contrast enhances the difference in color and light

between parts of an image.

You can set the value from 1 to .

Sharpness:

Sharpness determines the amount of

detail that an imaging system can reproduce.

You can set the value from 1 to 10.

Saturation:

You can set the saturation level of the image. The

value is from 0 to 10.

DNR:

DN R decreases the noise effect, especially in low

light conditions and delivers more accurate and

sharp image quality. You can set the value from

0 to 7.

:Mirror

You can set the Mirror status as H, V, H V, or OF F.

3 Menu Operation

Figure 3-1 Main Menu

VIDEO

SETTING

DAY/NIGHTWB RESET

BRIGHTNESS MODE

INFRARED

SMART IR

CONTRAST

SHARPNESS

SATURATION

EXITAE

DNR

MIRROR

EXPOSURE MODE

AGC

SAVE/EXIT

With a coaxial camera controller (purchase

separately) or calling the preset No.95 you can

select the menu and adjust the camera parameters.

3.1 FORMAT

You can set the format as PAL/NTSC.

3.2 SET UP

Move the cursor to , and press menu buttonSET U P

to enter the SET UP sub menu.

EXPOSURE

1.BRIGHTNESS

2.EXPOSURE MODE

LEVEL

3.AGC

4.RETURN

BLC

MIDDLE

Move the cursor to WB, and you can set White

Balance mode as and in this menuAWB MWB .

AWB: white balance is being adjusted

automatically.

: Set the value from 1 to 10.MWB R GAIN/B GAIN

As shown in Figure 3-3.

MODE MWB

R GIAN 1-|--10

B GAIN 1-|--10

RETURN 8

AGC:

AGC optimizes the clarity of image in poor light

scene. AGC level can be set as OFF, LOW, MIDDLE

and HIGH.

Figure 3-2 EXP OSURE

Figure 3-3 WB

Figure 3-4 DAY/NIGHT

3.2.3 DAY & NIGHT

Move the cursor to DAY & NIGHT, and select

COLOR B/W SMART, , or as the DAY & NIGHT mode.

COLOR: The image is colored in day mode all the

time.

: The image is black & white all the time, andB/W

the IR LED turns on in the low-light conditions.

: Select to turn on/off the INFRARED_LAMPSMART

and to set the Smart IR level from 1to 16.

As shown in Figure 3-4.

DAY/NIGHT

MODE SMART

INFRARED OFF

SMART IR 0-|--5

RETURN 8

3.2.7 SAVE/EXIT

3.2.5 Reset

Reset all the settings to the default.

3.2.6 EXIT

Exit and Save & exit are selectable.

Move the cursor to , and press OK toSAVE & Exit

save the settings and exit the menu.

Product specificaties

Merk:	Hikvision
Categorie:	Bewakingscamera
Model:	DS-2CE56D1T-AVPIR3(2.8-12MM)
Kleur van het product:	Wit
Gewicht:	880 g
Soort:	IP-beveiligingscamera
Internationale veiligheidscode (IP):	IP66
Vormfactor:	Dome
Ondersteuning voor plaatsing:	Binnen
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Nee
Montagewijze:	Plafond
Ondersteunde video-modi:	1080p
Maximum resolutie:	1920 x 1080 Pixels
Totaal aantal megapixels:	2 MP
Diameter:	145.2 mm
Stroomuitvoer (volt):	12
Minimale belichting:	0.1 Lux
Field of view (FOV) hoek:	102 °
Nachtvisie:	Ja
Brandpuntbereik:	2.8 - 12 mm
Vermogensverbruik (max):	4 W
Formaat analoog signaal:	NTSC, PAL
Volledige HD:	Ja
Omvang optische sensor:	1/3 "
Type beeldsensor:	CMOS
Optische zoom:	- x
Camera sluitertijd:	0.00002 - 0.33 s
Ingebouwde microfoon:	Ja
Lengte:	124.1 mm
Maximaal 30 frames per seconde:	30 fps
Progressive scan:	Ja
Composiet video-uitgang:	1
Signaal/ruis-verhouding:	52 dB
Scherpstellen:	1.4
PTZ control:	Ja
Draaihoek:	355 °
Pan bereik:	0 - 355 °
Nachtkijker afstand:	40 m
Aanpassing van de afbeeldingskwaliteit:	Brightness, Colour depth
Bedrijfstemperatuur (T-T):	-40 - 60 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Bereik kantelhoek:	0 - 90 °
Draaien & spiegelen:	Ja