Hikvision DS-2CE56C0T-VPIR(6MM) Handleiding

Hikvision Bewakingscamera DS-2CE56C0T-VPIR(6MM)

Lees hieronder de 📖 handleiding in het Nederlandse voor Hikvision DS-2CE56C0T-VPIR(6MM) (4 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

TVI Dome Camera

User Manual

Regulatory Information

FCC Information

FCC compliance: This equipment has been

tested and found to comply with the limits for a

digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated in

a commercial environment. This equipment

generates, uses, and can radiate radio

frequency energy and, if not installed and used

in accordance with the instruction manual, may

cause harmful interference to radio

communications. Operation of this equipment in

a residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his own

expense.

FCC Conditions

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference.

2. This device must accept any interference

received, including interference that may

cause undesired operation.

EU Conformity Statement

upon the purchase of equivalent new equipment,

or dispose of it at designated collection points.

For more information see: www.recyclethis.info.

2006/66/EC (battery directive):This

product contains a battery that cannot

be disposed of as unsorted municipal

waste in the European Union.

See the product documentation for specific

battery information. The battery is marked with

this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg).

For proper recycling, return the battery to your

supplier or to a designated collection point. For

more information see: www.recyclethis.info.

UD.6L0201D1931A01

2012/19/EU (WEEE directive):

Products marked with this symbol

cannot be disposed of as unsorted

municipal waste in the European

Union. For proper recycling, return

this product to your local supplier

This product and - if applicable - the

supplied accessories too are marked

with "CE" and comply therefore with

the applicable harmonized European

standards listed under the Low Voltage Directive

2006/95/EC, the EMC Directive 2004/108/EC,

the RoH S Directive 2011/65/EU.

TURBO

TURBOTURBO HD

HDHD

This series of camera adopts new generation

sensor with high sensitivity and advanced circuit

design technology It features high resolution,.

low image distortion and low noise, etc , which.

makes it suitable for surveillance system and

image processing system.

l High performance CMOS sensor and high

resolution bring high-quality image;

l Low illumination;

l OSD menu, parameters are configurable;

l Support auto white balance, auto gain control,

Support image effect adjustment;

Unit transmission control;

l Advanced 3-axis design meets different

installation requirements.

1 Introduction

1.1 Product Features

1.2 Overview

1.2.1 Overview of Type I Camera

1.2.2 Overview of Type Camera

2 Installation

Before you start:

l Please make sure that the device in the package

is in good condition and all the assembly parts

are included.

l Make sure that all the related equipment is

power-off during the installation.

l Check the specification of the products for the

installation environment.

l Check whether the power supply is matched

with your power output to avoid damage.

l Please make sure the wall is strong enough to

withstand three times the weight of the camera

and the mounting.

l If the wall is the cement wall, you need to insert

expansion screws before you install the camera.

If the wall is the wooden wall, you can use

self-tapping screw to secure the camera.

l If the product does not function properly,

please contact your dealer or the nearest

service center. Do not disassemble the camera

for repair or maintenance by yourself.

2.1 Installation of Type CameraI

2.Drill the screw holes and cable hole according to

the drill template.

Figure 2-2 The Drill Template

Screw Hole

Bubble

Video Cable

Power Cable

Adjustment Screw

Camera

Black Liner

Moungting Base

Adjustment Screw

Black Liner

Bubble

IR LED

Lens

Safety Rope

1.Pry the snap joint up to remove the bubble

and the black liner.

Cable Hole

Snap Joint

Figure 2-1 Remove the Bubble

Steps:

Thank you for purchasing our product. If there

are any questions, or requests, please do not

hesitate to contact the dealer.

This manual applies to

This manual may contain several technical

incorrect places or printing errors, and the

content is subject to change without notice.

The updates will be added to the new version of

this manual. We will readily improve or update

the products or procedures described in the

manual.

0100001050409

Please refer to the product specification for

camera parameters and functions.

Privacy Notice

Surveillance laws vary by jurisdiction. Check

all relevant laws in your jurisdiction before using

this product for surveillance purposes to ensure

that your use of this product conforms.

Type

Model

DS-2CE56D1T-IRMM

DS-2CE56D1T-VPI R

2.2 Installation of Type CameraII

3.Align the base plate with the mounting template

and secure it with supplied self-tapping screws.

4. Route the cables through the cable hole.

5. Connect the corresponding cables.

6. Adjust the camera according to the figure below

to get an optimum angle.

8. Push the black liner and bubble toward the

camera and buckle them upon to secure them on

the camera.

Base Plate

Figure 2-3 Fix the Camera to the Ceiling

PP Direction

Direction

DirectionDirection

0 ~350° °

0 ~70° °

TT Direction

Direction

DirectionDirection

Figure 2-4 3-axis Adjustment

Figure 2-5 Complete the Installation

1.Loosen the screws on the bubble to remove the

bubble and the black liner.

Figure 2-6 Remove the Bubble

2.Drill the screw holes and cable hole on the

ceiling according to the supplied drill template.

Drill Template

Hole A: fo r cables rout ed t hro ugh t he c e iling

sc rew hole 1: f o r Mo unt ing Ba se

Figure 2-7 Drill Template

Screw Hole

Cable Hole

3.Align the base plate with the mounting template

and secure it with supplied self-tapping screws.

4. Route the cables through the cable hole.

5. Connect the corresponding cables.

6. Adjust the camera according to the figure below

to get an optimum angle.

Figure 2-8 Fix the Camera to the Ceiling

8. Fit the black liner and bubble on the camera.

RR Direction

Direction

DirectionDirection

-15 ~15° °

0 ~75° °

PP Direction

Direction

DirectionDirection

0 ~360° °

TT Direction

Direction

DirectionDirection

TT Direction

Direction

DirectionDirection

Adjustment

AdjustmentAdjustment

Screw

ScrewScrew

Figure 2-9 3-axis Adjustment

Figure 2-10 Complete the Installation

Rotate the bubble after completing the

Installation may change the postion of the lens.

0 ~350° °

RR Direction

Direction

DirectionDirection

3.2.2 W B

3.2.1 AE

Move the cursor to AE, and you can adjust the

image brightness by the ,BRIG HT N ESS EXPOSURE

MODE AGC, and .

:Brightness

Brightness refers to the brightness of the image.

Exposure Mode:

Move the cursor to , you can selectExposure Mode

the exposure mode between and .Globe BLC

When BL C is selected as the exposure mode, the

level of BLC mode can be adjusted, as shown in the

Figure 3-2.

3.2.4 VIDEO SETTING

Contrast:

Contrast enhances the difference in color and light

between parts of an image.

You can set the value from 1 to .

Sharpness:

Sharpness determines the amount of

detail that an imaging system can reproduce.

You can set the value from 1 to 10.

Saturation:

You can set the saturation level of the image. The

value is from 0 to 10.

DNR:

DNR decreases the noise effect, especially in low

light conditions and delivers more accurate and

sharp image quality. You can set the value from

0 to 7.

:Mirror

You can set the Mirror status as H, V, HV, or OFF.

3 Menu Operation

Figure 3-1 Main Menu

VIDEO

SETTING

DAY/NIGHTWB RESET

BRIGHTNESS MODE

INFRARED

SMART IR

CONTRAST

SHARPNESS

SATURATION

EXITAE

DNR

MIRROR

EXPOSURE MODE

AGC

SAVE/EXIT

With a coaxial camera controller (purchase

separately) or calling the preset No.95 you can

select the menu and adjust the camera parameters.

3.1 FORMAT

You can set the format as PAL/NTSC.

3.2 SE T UP

Move the cursor to , and press menu buttonSET UP

to enter the SET UP sub menu.

EXPOSURE

1.BRIGHTNESS

2.EXPOSURE MODE

LEVEL

3.AGC

4.RETURN

BLC

MIDDLE

Move the cursor to WB, and you can set White

Balance mode as and in this menuAWB MWB .

AWB: white balance is being adjusted

automatically.

: Set the value from 1 to 10.MWB R GAIN/B GAIN

As shown in Figure 3-3.

MODE MWB

R GIAN 1-|--10

B GAIN 1-|--10

RETURN 8

AGC:

AGC optimizes the clarity of image in poor light

scene. AGC level can be set as OFF, LOW, MIDDLE

and HIGH.

Figure 3- 2 EXPOSU RE

Figure 3-3 WB

Figure 3-4 DAY/NIGHT

3.2.3 DAY & NIGHT

Move the cursor to DAY & NIGHT, and select

COLOR B/W SMART, , or as the DAY & NIGHT mode.

COLOR: The image is colored in day mode all the

time.

: The image is black & white all the time, andB/W

the IR LED turns on in the low-light conditions.

: Select to turn on/off the INFRARED_LAMPSMART

and to set the Smart IR level from 1to 16.

As shown in Figure 3-4.

DAY/NIGHT

MODE SMART

INFRARED OFF

SMART IR 0-|--5

RETURN 8

3.2.7 SAVE/EXIT

3.2.5 Reset

Reset all the settings to the default.

3.2.6 EXIT

Exit and Save & exit are selectable.

Move the cursor to , and press OK toSAVE & Exit

save the settings and exit the menu.

Product specificaties

Merk:	Hikvision
Categorie:	Bewakingscamera
Model:	DS-2CE56C0T-VPIR(6MM)
Kleur van het product:	Wit
Gewicht:	550 g
Hoogte:	82.4 mm
Internationale veiligheidscode (IP):	IP66
Vormfactor:	Dome
Connectiviteitstechnologie:	Bedraad
Montagewijze:	Plafond
Ondersteunde video-modi:	720p
Maximum resolutie:	1296 x 732 Pixels
Totaal aantal megapixels:	1 MP
Diameter:	111 mm
Minimale belichting:	0.1 Lux
Field of view (FOV) hoek:	56.7 °
Aantal cameras:	1
Ingebouwde HDD:	Nee
Nachtvisie:	Ja
LED-type:	IR
Formaat analoog signaal:	NTSC, PAL
Volledige HD:	Nee
Type beeldsensor:	CMOS
Camera sluitertijd:	1/50000 - 1/30 s
Veiligheidsfunties:	Vandaalbestendig
Maximaal 30 frames per seconde:	30 fps
Signaal/ruis-verhouding:	62 dB
IK code:	IK10
Draaihoek:	355 °
Pan bereik:	0 - 355 °
Dag/nacht modus:	Ja
Weerbestendig:	Ja
Nachtkijker afstand:	20 m
Wifi:	Nee
Stroomverbruik (typisch):	4 W
Bedrijfstemperatuur (T-T):	-40 - 60 °C
Bereik kantelhoek:	0 - 75 °