Hikvision DS-2CE16D5T-VFIT3 Handleiding

Hikvision Bewakingscamera DS-2CE16D5T-VFIT3

Lees hieronder de 📖 handleiding in het Nederlandse voor Hikvision DS-2CE16D5T-VFIT3 (4 pagina's) in de categorie Bewakingscamera. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

TURBO HD

1080P Turret &Bullet Camera

User Manual

Regulatory Information

FCC Information

FCC compliance: This equipment has been

tested and found to comply with the limits for a

digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference when the equipment is operated in

a commercial environment. This equipment

generates, uses, and can radiate radio

frequency energy and, if not installed and used

in accordance with the instruction manual, may

cause harmful interference to radio

communications. Operation of this equipment in

a residential area is likely to cause harmful

interference in which case the user will be

required to correct the interference at his own

expense.

FCC Conditions

This device complies with part 15 of the FCC

Rules. Operation is subject to the following two

conditions:

1. This device may not cause harmful

interference.

2. This device must accept any interference

received, including interference that may

cause undesired operation.

EU Conformity Statement

upon the purchase of equivalent new equipment,

or dispose of it at designated collection points.

For more information see: www.recyclethis.info.

2006/66/EC (battery directive):

This product contains a battery that

cannot be disposed of as unsorted

municipal waste in the European

Union.

See the product documentation for specific

battery information. The battery is marked with

this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg).

UD.6L0201D1551A02

2012/19/EU (WEEE directive):

Products marked with this symbol

cannot be disposed of as unsorted

municipal waste in the European

Union. For proper recycling, return

this product to your local supplier

This product and - if applicable - the

supplied accessories too are marked

with "CE" and comply therefore with

the applicable harmonized European

standards listed under the Low Voltage Directive

2006/95/EC, the EMC Directive 2004/108/EC,

the RoHS Directive 2011/65/EU.

1.2 Overview

1.2.1 Overview of Type I Camera

1.2.2 Overview of Type Camera

HD Video Cable

CVBS Cable

Switch Cable

Enclosure

Zoom & Focus

Lock ButtonLock Button

Mounting Base

Camera

Power Cab le

Power Cable

IR LED

Lens

Main Body

Sun Shield

Mounting Base

Switch Cable

HD Video Cable

CVBS Cable

Zoom

Focus

1 Introduction

1.1 Product Features

This camera adopts new generation sensor with

high sensitivity and advanced circuit board design

technology. It possesses the features of high

resolution, low distortion, and low noise, etc. It is

extremely suitable for supervisory system and

image processing system.

The main features are as follows:

l High performance CMOS sensor and high

resolution bring high-quality image;

l Low illumination;

l Support IR cut filter with auto switch;

l OSD menu, parameters are configurable;

l Support auto white balance, auto gain control,

electronic shutter control and internal

synchronization;

l SMART IR mode;

l Unit transmission control;

l Advanced 3-axis design meets different

installation requirements.

l Please make sure that the device in the package

is in good condition and all the assembly parts

are included.

l Make sure that all the related equipment is

power-off during the installation.

l Check the specification of the products for the

installation environment.

l Check whether the power supply is matched

with your power output to avoid damage.

l Please make sure the wall is strong enough to

withstand three times the weight of the camera

and the mounting.

l If the wall is the cement wall, you need to insert

expansion screws before you install the camera.

If the wall is the wooden wall, you can use

self-tapping screw to secure the camera.

l If the product does not function properly,

please contact your dealer or the nearest

service center. Do not disassemble the camera

for repair or maintenance by yourself.

2.1 Installation of Type CameraI

Steps:

1.Drill the screw holes and the cable hole on the

ceiling according to the supplied drill template.

Figure 2-1 The Drill Template

2 Push the lock button to disassemble the camera

from the mounting base.

3.Fix the mounting base to the ceiling.

Figure 2-2 Release The Lock Screw

PUSH

For proper recycling, return the battery to your

supplier or to a designated collection point. For

more information see: www.recyclethis.info.

2 Installation

Before you start:

Thank you for purchasing our product. If there

are any questions, or requests, please do not

hesitate to contact the dealer.

This manual may contain several technical

incorrect places or printing errors, and the

content is subject to change without notice.

The updates will be added to the new version of

this manual. We will readily improve or update

the products or procedures described in the

manual.

DISCLAIMER STATEMENT

Underwriters Laboratories Inc. (”UL” has not)

tested the performance or reliability of the

security or signaling aspects of this product.

UL has only tested for fire, shock or casualty

hazards as outlined in Ul’s Standard(s) for Safety,

UL60950-1. UL Certification does not cover the

performance or reliability of the security or

signaling aspects of this product. UL MAKES NO

REPRESENTATIONS, WARRANTIES OR

CERTIFICATIONS WHATSOEVER REGARDING

0100001040603

THE PERFORMANCE OR RELIABILITY OF ANY

SECURITY OR SIGNALING RELATED FUNCTIONS

OF THIS PRODUCT.

Figure 1-1 Overview of Type I Camera

Figure 1-2 Overview of Type CameraII

3 Menu Operation

Steps:

1.Drill the screw holes and the cable hole in the

ceiling according to the supplied drill template.

2.Hammer the supplied plastic expansion bolt into

the screw holes.

2.2 Installation of Type IICamera

Figure 2-5 Drill Template

Figure 2-6 Fix the Camera to the Ceiling

Figure 2-7 3-axis Adjustment

5. Adjust the surveillance angle.

1). Loosen No.1 adjusting screw to adjust the pan

position (0 ~ 360 ).° °

2).Tighten No.1 adjusting screw.

3). Loosen No.2 adjusting screw to adjust the

tilting position(0 ~ 90 ).° °

4).Tighten No.2 adjusting screw.

5). Loosen No.3 adjusting screw to adjust the

rotation position 0 ~ 360 .( ° °)

6).Tighten No.3 adjusting screw.

3.Route the cables to the cable hole and connect

the corresponding cables.

4.Fix the camera to the ceiling with the supplied

screws.

4.Route the cables to the cable hole and connect

the corresponding cables.

5.Secure the camera to the mounting base by

tightening the lock screw.

6.Adjust the camera according to the figure below

to get an optimum angle.

Figure 2-3 3-axis Adjustment

7.Use the screwdriver to adjust the ZOOM screw

and the FOCUS screw until you get the optimum

image.

Figure 2-4 Zoom and Focus Adjustment

0 ~360

0 ~75

0~360

Both wall mounting and ceiling mounting are

suitable for type bullet camera. Ceiling mounting

will be taken as an example in the section. And you

can take steps of ceiling mounting as a reference

if wall mounting is adopted.

0~ 360

0~ 90

Figure 3-1 Main Menu

SCENE LENS RESET

EXPOSURE WB DAY&NIGHT

BACKLIGHT NR SPECIAL ADJUST

INDOOR

OUTDOOR

INDOOR1

LOW-

LIGHT

MANUAL SHUT TER

AGC

SENS-UP

BRIGHTNESS

D-WDR

DEFOG

BLC

HSBLC

ATW

AWC-SET

MANUAL

COLOR

B/W

EXT

2D NR

3D NR

CAM

TITLE

D-EFFECT

MOTION

PRIVACY

LAUGUAGE

DEFECT

VERSION

SHARPNESS

MONITOR

LSC

VIDEO.

OUT

EXIT

SETUP

You can call the menu and adjust the camera

parameters with a coaxial camera controller

(purchase separately). You can also call the menu

with supported TVI DVR.

3.1 VIDEO.OUT

PAL or NTSC is selectable .

3.2 LANGUAGE

English, Japanese, CHN1, CHN2, Korean, German,

French, Italian, Spanish, Polish, etc., are selectable.

3.3SETUP

3.3.1 SCENE

You can select indoor, outdoor, indoor 1 and low

-light as the working environments.

3.3.2 LENS

The camera is equipped with a fixed lens.

3.3.3 EXPOSURE

EXPOSURE

1. SHUTTER AUTO

2. AGC OFF

3. SENS-UP ---

4. BRIGHTNESS ---|------ 40

5. DEFOG OFF

6. D-WDR OFF

7. RETURN RET

Figure 3-2 Exposure

SHUTTER: AUTO,1/25, 1/50, FLK, 1/200, 1/400,

1/1k, 1/2k, 1/5k, 1/10k, 1/50k, x2, x4, x6, x8, x10,

and x15 are selectable.

: You can set the AGC value from 0 to 15.AGC

: You can set the SENS-UP to OFF or AUTO.SENS-UP

: You can set the brightness valueBRIGHTNESS

from 1 to 100.

: You can set the defog function as ON toDEFOG

enable the function. Position, size, and the defog

gradation are configurable.

You can set the D-WDR as ON or OFF.D-WDR:

3.3.4 Backlight

Backlight Compensation (BLC):

Set the gain of BLC as High, Middle, or Low.-GAIN:

Press the up/down/left/right button to-AREA:

define the BLC position and size. Select RET or

AGAIN to go back the BLC menu or re-define the

BLC area.

Restore the BLC settings to the default.-Default:

HSBLC: Select an HSBLC area. Set the DISPLAY

status as ON. Press the up/down/left/right button

to define the area position and size. Set the HSBLC

LEVEL from 0 to 100. Select ALL DAY or Night for the

HSBLC mode. Set the BLACK MASK status as ON or

OFF.

HSBLC

1. SELECT AREA 1

2. DISPLAY ON 8

3. LEVEL ---|------ 40

4. MODE ALL DAY

5. BLACK MASK ON

6. DEFAULT 8

7. RETURN RET

Figure 3-3 HSBLC

3.3.5 White Balance (WB)

MANUAL, ATW (Auto-tracking White Balance),

AWC→SET are selectable.

3.3.6 Day & Night

Color, B/W, and EXT are selectable for DAY and

NIGHT switches.

3.3.7 NR

: You can set 2D NR status as ON or OFF.2D NR

: Set the Smart NR status as ON and adjust3D NR

the 3D smart NR sensitivity ranges from 0 to 100.

Set the 3D NR LEVEL ranges from 0 to 100. Set the

2D&3D NR

1. 2DNR OFF

2. 3DNR ON 8

3. RETURN RET

3D NR

1. SMART NR ON8

2. LEVEL ------|--8 0

3. START. AGC -|--------10

4. END. AGC -|--------10

5. RETURN RET

Figure 3-4 NR

Figure 3-5 3D NR

3.3.8 SPECIAL

Edit the camera title on this section.Camera Title:

D-effect:

Set the freeze function as ON or OFF.-FREEZE:

OFF, MIRROR, V-FLIP, and ROTATE are-MIRROR:

selectable for mirror.

Define the zoom area by configuring-D-ZOOM:

the position from PAN & TILT.

The D-Zoom area, sensitivity-SMART D-ZOOM:

and time are configurable.

Set the NEG IMAGE as ON or OFF.-NEG.IMAGE:

SPECIAL

1. CAM TITLE ON 8

2. D-DFFECT 8

3. MOTION OFF

4. PRIVACY OFF

5. LANGUAGE ENG 8

6. DEFECT 8

7. RETURN RET

Figure 3-6 Special

MOTION

1. SELECT AREA 1

2. DISPLAY ON8

3. SENSITIVITY ----|---- 30

4. MOTION VIEW ON

5. DEFAULT 8

6. RETURN RET

Figure 3-7 Motion Detection

Motion: Select a MOTION area. Set the DISPLAY

status as ON or OFF. Press the up/down/left/right

button to define the position and size of the area.

Set the SENSITIVITY from 0 to 60. Set the MOTION

VIEW status as ON or OFF.

Privacy: Select a PRIVACY area. Set the DISPLAY

status as INV, MOSAIC, COLOR or OFF. Press the

up/down/left/right button to define the position

and size of the area.

Defect: LIVE DPC, STATIC DPC and Black DPC are

adjustable in this section.

PRIVACY

1. SELECT AREA 1

2. DISPLAY MOSAIC 8

3. COLOR 10

4. TRANS. 1

5. DEFAULT 8

6. RETURN RET

ADJUST

1. SHARPNESS --------|15

2. MONITOR LCD8

3. LSC OFF

4. RETURN RET

3.3.9 ADJUST

: Adjust the sharpness from 0 to 15.Sharpness

: Monitor CRT, and Monitor LCD areMonitor

selectable.

: Set the LSC status as ON or OFF.LSC

3.3.10 RESET

Reset all the settings to the default.

3.3.11 EXIT

Press OK to exit the menu.

START. AGC level as the threshold to enable AGC,

and set the END. AGC level as the threshold to

disable AGC.

Figure 3-8 Privacy Mask Figure 3-9 Adjust

Product specificaties

Merk:	Hikvision
Categorie:	Bewakingscamera
Model:	DS-2CE16D5T-VFIT3
Kleur van het product:	Black, White
Gewicht:	700 g
Breedte:	100.76 mm
Hoogte:	107.55 mm
Internationale veiligheidscode (IP):	IP66
Vormfactor:	Rond
Ondersteuning voor plaatsing:	Buiten
Connectiviteitstechnologie:	Bedraad
Ethernet LAN:	Nee
Montagewijze:	Plafond/muur
Ondersteunde video-modi:	1080p
Maximum resolutie:	1944 x 1092 Pixels
Totaal aantal megapixels:	2 MP
Stroomuitvoer (volt):	12
Minimale belichting:	0.01 Lux
Nachtvisie:	Ja
LED-type:	IR
Zoomcapaciteit:	Ja
Brandpuntbereik:	- mm
Vermogensverbruik (max):	7 W
Formaat analoog signaal:	NTSC, PAL
Volledige HD:	Ja
Type beeldsensor:	CMOS
Digitale zoom:	62 x
Optische zoom:	- x
Camera sluitertijd:	1/25(1/30) - 1/50000 s
Witbalans:	ATW, AWC, Indoor, Manual, Outdoor
Ruisonderdrukking:	Ja
Lengte:	300.82 mm
Signaal/ruis-verhouding:	62 dB
Ondersteunde talen:	ARA, DEU, DUT, ENG, ESP, FRE, HEB, ITA, JPN, KOR, POL, POR, RUS, TUR
Scherpstellen:	1.4
PTZ control:	Ja
Draaihoek:	360 °
Pan bereik:	0 - 360 °
Dag/nacht modus:	Ja
BNC output ports:	1
Bewegingssensor:	Ja
Weerbestendig:	Ja
Nachtkijker afstand:	50 m
Wide Dynamic Range (WDR):	Ja
Bedrijfstemperatuur (T-T):	-30 - 60 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Bereik kantelhoek:	0 - 90 °
Privézone maskeren:	Ja
Kijkhoek lens, horizontaal:	103 °
Draaien & spiegelen:	Ja
Kijkhoek lens, verticaal:	32.1 °