Hikoki CR13VB Handleiding

Hikoki Zaagmachine CR13VB

Lees hieronder de 📖 handleiding in het Nederlandse voor Hikoki CR13VB (12 pagina's) in de categorie Zaagmachine. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/12
NOTE:
Before using this Electric Power Tool, carefully read through these
HANDLING INSTRUCTIONS to ensure efficient, safe operation. It is
recommended that these INSTRUCTIONS be kept readily available
as an important reference when using this power tool.
Reciprocating Saw
Model CR 13VB
Handling instructions
1
f)
Dress properly. Do not wear loose clothing or jewellery.
Keep your hair and clothing away from moving parts.
Loose clothes, jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities, ensure
these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
h)
Do not let familiarity gained from frequent use of tools allow
you to become complacent and ignore tool safety principles.
A careless action can cause severe injury within a
fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and safer
at the rate for which it was designed.
b) Do not use the power tool if the switch does not
turn it on and off .
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d)
Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e)
Maintain power tools and accessories. Check
for misalignment or binding of moving parts,
breakage of parts and any other condition that
may aff ect the power tool s operation. If damaged, ʼ
have the power tool repaired before use.
Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to control.
g)
Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations diff erent from
those intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean
and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe
handling and control of the tool in unexpected situations.
5) Service
a)
Have your power tool serviced by a qualifi ed repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
PRECAUTION
Keep children and infi rm persons away.
When not in use, tools should be stored out of reach of
children and infi rm persons.
RECIPROCATING SAW SAFETY WARNINGS
1.
Hold the power tool by insulated gripping surfaces,
when performing an operation where the cutting
accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a "live" wire may make
exposed metal parts of the power tool "live" and could
give the operator an electric shock.
2. Use clamps or another practical way to secure and
support the workpiece to a stable platform.
Holding the workpiece by hand or against your body
leaves it unstable and may lead to loss of control.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings, instructions, illustrations and
specifi cations provided with this power tool.
Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b)
Do not operate power tools in explosive atmospheres, such
as in the presence of fl ammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a)
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodifi ed plugs and matching outlets will reduce
risk of electric shock.
b)
Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c)
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an
extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the
risk of electric shock.
f)
If operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or under
the infl uence of drugs, alcohol or medication.
A moment of inattention while operating power tools
may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as a dust mask, non-skid
safety shoes, hard hat or hearing protection used for
appropriate conditions will reduce personal injuries.
c)
Prevent unintentional starting. Ensure the switch is
in the off -position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your fi nger on the switch or energising
power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part of
the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
2
SPECIFICATIONS
Voltage (by areas)* (110V, 115V, 120V, 127V, 220V, 230V, 240V)
Power Input 1050 W*
Capacity Mild Steel Pipe: O.D. 130 mm
Vinyl Chloride Pipe: O.D. 130 mm
Wood: Depth 300 mm
Mild Steel Plate: Thickness 19 mm
No-Load Speed 0 – 2800 /min
Stroke 32 mm
Weight (without cord) 4.0 kg
STANDARD ACCESSORIES
(1) Blade (No. 103) .................................................... 1
(2) Case ........................................................................ 1
Standard accessories are subject to change without
notice.
OPTIONAL ACCESSORIES (sold separately)
(1) No. 1 Blade (12) No. 103 Blade
(2) No. 2 Blade (13) No. 104 Blade
(3) No. 3 Blade (14) No. 105 Blade
(4) No. 4 Blade (15) No. 106 Blade
(5) No. 5 Blade (16) No. 107 Blade
(6) No. 8 Blade (17) No. 108 Blade
(7) No. 9 Blade (18) No. 121 Blade
(8) No. 95 Blade (19) No. 131 Blade
(9) No. 96 Blade (20) No. 132 Blade
(10) No. 101 Blade
(11) No. 102 Blade
䡬(1) – (9) : HCS Blades (HCS : Highspeed Carbon Steel)
䡬(10) – (20) : Bl-METAL Blades
Refer to for use of the blades.Table 1, 2 and 3
Optional accessories are subject to change without notice.
APPLICATIONS
䡬Cutting pipe and angle steel.
䡬Cutting various lumbers.
䡬Cutting mild steel plates, aluminum plates, and copper
plates.
䡬Cutting synthetic resins, such as phenol resin and
vinyl chloride.
For details refer to the section entitled “SELECTION OF
BLADES”.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirement specied on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position. If
the plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sucient thickness
and rated capacity. The extension cord should be kept
as short as practicable.
4. Dust produced in operation
The dust produced in normal operation may aect
the operator’s health. To wear a dust mask is
recommended.
5. Mounting the blade
This unit employs a detachable mechanism that
enables mounting and removal of saw blades without
the use of a wrench or other tools.
(1) Turn on and othe switching trigger several times
so that the lever can jump out of the front cover
completely. Thereafter, turn off the switch and unplug
the power cord. (Fig. 1)
CAUTION
Be absolutely sure to keep the switch turned o and
the power cord unplugged to prevent any accident.
Fig. 1
(2) Push the lever in the direction of the arrow mark
shown in marked on the lever.Fig. 2
Fig. 2
* Be sure to check the nameplate on product as it is subject to change by areas.
Lever
Lever Front cover

Product specificaties

Merk: Hikoki
Categorie: Zaagmachine
Model: CR13VB

Heb je hulp nodig?

Als je hulp nodig hebt met Hikoki CR13VB stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Zaagmachine Hikoki

Hikoki

Hikoki C8FSE Handleiding

12 Maart 2024
Hikoki

Hikoki C10FCE2 Handleiding

29 Augustus 2023
Hikoki

Hikoki C10RJ Handleiding

29 Augustus 2023
Hikoki

Hikoki M 12SA2 Handleiding

29 Augustus 2023
Hikoki

Hikoki C1806DB Handleiding

29 Augustus 2023
Hikoki

Hikoki C 3606DPA Handleiding

29 Augustus 2023
Hikoki

Hikoki C 3607DA Handleiding

29 Augustus 2023
Hikoki

Hikoki M 12V2 Handleiding

29 Augustus 2023
Hikoki

Hikoki C3610DRJ Handleiding

29 Augustus 2023
Hikoki

Hikoki C7YA Handleiding

3 Augustus 2023

Handleiding Zaagmachine

Nieuwste handleidingen voor Zaagmachine

Worx

Worx Nitro WX542.9 Handleiding

26 April 2024
Fieldmann

Fieldmann FZP 25410-B Handleiding

15 April 2024
Milwaukee

Milwaukee M18 BJS Handleiding

10 April 2024
Rona

Rona Standard Plus-C Handleiding

10 April 2024
Rona

Rona Profi-C Handleiding

10 April 2024
Milwaukee

Milwaukee SCS 65 Q Handleiding

10 April 2024
Milwaukee

Milwaukee M12 BS Handleiding

10 April 2024
Milwaukee

Milwaukee M18 FMCS66 Handleiding

10 April 2024
Milwaukee

Milwaukee M18 BSX Handleiding

10 April 2024
Bavaria By Einhell

Bavaria By Einhell BFS 800E Handleiding

9 April 2024