Hifonics ZEUS ZD-1750.5D Handleiding

Bekijk gratis de handleiding van Hifonics ZEUS ZD-1750.5D (2 pagina’s), behorend tot de categorie Keverőgép. Deze gids werd als nuttig beoordeeld door 37 mensen en kreeg gemiddeld 4.5 sterren uit 8 reviews. Heb je een vraag over Hifonics ZEUS ZD-1750.5D of wil je andere gebruikers van dit product iets vragen? Stel een vraag

Place terminal in a secure

position so that it won’t

accidentally contact the

negative battery post

Power cable size

and fusing

It is critical to use the proper power

and ground cable. Select the size

listed here for your amplier model.

Always use high quality copper

cable. Visit our website for multi amp

system cable recommendations.

Be sure to use the proper fuse size

for each model.

Properly route power,

speaker and RCA cables

through the vehicle.

Choose a mounting location

that will provide adequate air

ventilation. Mount the amplier to

a secure surface. Do not mount

the amplier upside down.

Attach the chassis ground

cable to the amplier

negative terminal. It is

important to make sure this

connection is very tight.

Bare metal

Attach the main power cable

to the amplier +12V. The

cable must run directly to

the battery and be properly

fused and be very tight.

Attach the remote turn on

wire to the amplier remote

output of the source unit.

Connect the RCA cables to the

coordinating RCA input number

that will match the speaker

outputs number.

Connect the power cable to the

positive battery terminal. The

power cable must be fused

within 18 inches of the battery

terminal.

Re-connect the negative

battery terminal making sure it

is securely tightened.

The chassis ground connection

is critical to the performance

of the amplier. Choose a

location that is close to the

amplier. Completely scrape

away the paint and use a nut

and bolt if possible.

DO NOT USE AN EXISTING

FACTORY BOLT!

Disconnect

negative battery

terminal

Run Cables

Mount Amplier

Negative Power

Connection

Positive Power

Connection

Remote Turn-on

Connection

Signal Input

Connection

Positive Battery

Connection

Re-connect

Negative Battery

Terminal

Chassis Ground

Be prepared to disarm your vehicle’s alarm and

to enter your radio / source unit code.

Installation

Before you start

CAUTION

Many new and factory radios require a reset code when

disconnected from battery power. This is an anti-theft

feature. Before unplugging power, you must determine if

your radio/source unit requires a reset code. Check the

operation manual for your vehicle or contact the dealer.

1

2

3

5

7

6

8

11

12

4

POWER

High Level Input

- DC turn on

- Signal Sense turn on

Low Level Input

- REM turn on (Remote wire turn on)

Please check Hifonics.com/product-manuals

for the Auto-Sense Technical Guide.

Turn on Mode

9

Model Fuse Size Cable Size

4ga

2ga

Using spade terminals,connect

the speaker cables to the speaker

output connectors. Follow the

diagram below that best ts your

speaker conguration.

Speaker

Connections

Stereo

Monoblock Monoblock single woofermultiple woofers

Bridged

10

CH1 CH2

SPE AKE RSPE AKE R

REM

ON

DC

ON

SIGNAL

ON

MODE

NOTE - When using low level input and the RCA’s are plugged into the amplier and the TURN ON

MODE is in the DC ON position, the amplier will NOT turn on. Please re-read QR document above

or hire a professional installer.

External 80A

External 35A

External 60A

External 60A

External 100A

External 100A

External 125A

ZD-1350.1D

ZD-1250.2D

ZD-750.4D

ZD-1350.4D

ZD-1750.5D

ZD-1950.1D

ZD-2550.1D

ZD-3350.1DExternal 175A

Product specificaties