Hartke HT12 Handleiding
Pagina's 2 Niet gecategoriseerd
Bekijk de handleiding van Hartke HT12 gratis online of download de PDF. Deze handleiding is 0 keer bekeken. Vraag over dit model? Stel een vraag
Before using the tuner, please familiarize yourself with the various controls and indicators of the HT 12 Tuner as
shown on the other side of this page
Auto Tuning Procedure
1. For electric instruments: Use a standard guitar cable to connect the output jack of an instrument to the input () jack of the tuner. For IN
acoustic instruments: Position the instrument close to the HT 12 tuner facing the built-in microphone ().MIC
2. Press button to turn the Hartke HT 12 tuner on.The LCD will light up. POWER AUTOCHROMA,and a pitch reference of A 440Hz are the
default settings. (Note: the tuner will automatically shut off after 20 minutes with no sound input.)
3. Select the tuning mode you wish to use. Each press of the button will cycle through ,MODE CHROMAGUITARBASSVIOLIN, , and tun-
ing modes. mode will display the name of the note that is being played and how close to correct pitch it is. CHROMAGUITARBASS, , and
VIOLIN modes will display the name of the string (for the selected instrument) and note that is closest to the one the tuner is currently ana-
lyzing.
4. Pick one string on your instrument, creating the sound of a single note.
5. If either of the red LEDs light up and the name of the note/string you desire to tune is displayed on the LCD, slowly tighten or loosen the
string’s tuning key until meter needle reaches center position. If the string’s pitch is out of -50 or +50 cent range for the desired note, adjust
the string’s tuning key until the name of the note/string you desire to tune is displayed on the LCD and one of red LEDs (
or
) is illuminated.
6. When the string is in tune, the meter needle will stop at the center position and the green LED will be lit.
7. Repeat this process for each of the instrument’s strings that you wish to tune.
Manual Tuning Procedure
1. Pressing the button will switch the tuning operation from NOTE AUTO MANLto (manual).
2. In operation the notes/strings are selected in a specified order determined by the instrument selected. Pressing the button will MANL NOTE
skip/advance to the next note/string.
The following lists the order for each in which the notes/strings are tuned in operationMODE MANL
CHROMA - C, C
, D, D
, E, F, F
, G, G
, A, A
, B
GUITAR- 7B, 6E, 5A, 4D, 3G, 2B, 1E (six string guitars skip 7B)
BASS- LB, 4E, 3A, 2D, 1G, HC (four string basses skip LB & HC)
VIOLIN - 4G, 3D, 2A, 1E
3. Tune each note/string as in steps 4 – 6 of the Auto Tuning Procedure (above).
4. Press the button to tune the next note/string and continue the process until the whole instrument is in tune.NOTE
Advanced Tuning Procedures
1. If you require a standard pitch other than A 440Hz (the A above Middle C), select a standard pitch (A 433Hz – A 447Hz) using the but-PITCH
ton.
2. If you would like to tune your instrument down (i.e. for 6 string guitar E, A, D, G, B, E), press the FLAT button once for each half-step (semi-
tone) lower than standard pitch that you require. This will allow you to use the traditional string name (i.e. E, A, D, G, B, E) while utilizing a
lower pitch for those strings (i.e. E, A, D, G, B, E). Each time the FLAT button is pressed a flat mark () will be displayed in the LCD. The pitch
can be lowered up to 4 half-steps (semi-tones), or the equivalent of tuning a 6 string guitar down to C.
Alternatively, if you use Capo on your guitar, you can tune the guitar with the capo attached by using FLATFLAT tuning function. Press but-
ton once for each fret above the nut that the Capo is attached (up to 4 frets).
A flat sign () will appear (up to four ) on the display each time you push the FLAT button. They representing how many half-steps the string
will be tuned down relative to the selected or displayed note/string.
For Accurate Tuning
• When you tune electric instruments, position the volume level around the center “5” position.
• Avoid striking the strings heavily.
• Mute the strings lightly (with your fingers) when you are finished tuning a string before you begin tuning the next string.
Battery Installation
1. Slide the cover on bottom side in the direction of the arrow while pressing the cover.
2. Insert the batteries (AAA x 2, 1.5V) being careful to observe the correct polarity.
3. If the unit does not operate correctly, remove and then reinstall the batteries.
Hartke HT 12 Operation Manual
P. O. Box 9031
575 Underhill Blvd.
Syosset, NY 11791-9031
www.hartke.com
Specifications
Modes: Auto & Manual tuning mode
Tuning Range: A0 (27.50Hz) – C8 (4,186.00Hz)
Tuning Notes:
Chromatic Mode: C, C
, D, D
, E, F, F
, G, G
, A, A
, B
Guitar Mode: 7B, 6E, 5A, 4D, 3G, 2B, 1E
Bass Mode: LB, 4E, 3A, 2D, 1G, HC
Violin Mode: 4G, 3D, 2A, 1E
Accuracy: ±0.5 Cents
Pitch Range: A 433 – 447Hz (1Hz steps)
Indicators: LCD & 3 LEDs
Inputs:
Input Jack for Electric instruments
Condenser Microphone for Acoustic instruments
Power supply: 3V (2 x 1.5V AAA batteries)
Dimensions : (w) 2.6 x (h) 3.7 x (d) 43 in.
(w) 65 x (h) 93.5 x (d) 11 mm
Weight : 2.86 oz. / 81 g (Including Batteries)
Caution
1. To avoid short circuit, electric shock or malfunction:
Do not disassemble for repair.
Avoid excessive vibration.
Do not operate with wet hands.
Avoid high temperatures and humid spaces.
2. To avoid damage:
Do not handle controls with excessive force.
Do not drop the tuner.
3. Cleaning:
Do not use thinner or alcohol for cleaning.
Use only dry, clean cloth.
4. To prevent battery drain:
Turn the power off when the tuner is not in use.
Remove the battery when the tuner will not be used for an
extended period of time.
Limited Warranty
The Hartke HT 12 Tuner is covered by a limited 1 year warranty. If, during the 1 year period that immediately follows the date of the original
purchase your tuner is found, under normal usage, to have a defect in material or workmanship, SAMSON TECHNOLOGIES CORP. will repair or
replace the tuner without charge. To register your tuner via the internet, go to http://warranty.samsontech.com/, or call Samson Customer Service
at 1-800-372-6766. You must be able to provide proof of purchase at the time of any repair or replacement. Visit for warranty.samsontech.com
complete details. This warranty applies only to products sold in the USA, for warranty information on products not purchased in the United States,
please contact the Hartke distributor in the country where the product was purchased.
Hartke HT 12 Tuner Overview
Controls and Displays
A. Flat, In-Tune and Sharp LEDs
B. Liquid Crystal Display (LCD)
C. Tilt Back Stand (Rear of unit)
D. MICInternal Microphone for Acoustic Instruments
E. PITCH button (See Advanced Tuning Procedures)
F. NOTE button to switch strings in manual operation
G. POWER button
H. MODE button
I. FLAT button (See Advanced Tuning Procedures)
J. IN Input Jack for Electric Instruments
LCD Display Overview
1. Reference Pitch Display
2. FLAT Mode Indicator
3. Note/String Display
4. Tuning Meter/Needle
5. Tuning IndicatorMODE
6. AUTOMANUAL/Indicator
Product specificaties
| Merk: | Hartke |
| Categorie: | Niet gecategoriseerd |
| Model: | HT12 |
Heb je hulp nodig?
Als je hulp nodig hebt met Hartke HT12 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden